Question about 1998 Acura Integra Type R

1 Answer

Had a broken lug on a 96 teggy went to replace

Had a broken lug on a 96 teggy went to replace and theres no spot on the hub for the stud to move out, i tryed to remove hub with puller but it wont budge...please hepl

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 2,309 Answers

On that cat the hub is pressed into the bearing , you will have to remove the assembly and take it to a machine shop, most times the bearing seal will be damaged in the process so replace it as well

Posted on Jul 16, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace broken stud of honda crv 2001 front wheel


remove wheel, brake assembly & rotor. rotate to where the broken stud is in the opening where the brake assembly was. drive the broken stud out of the hub flange. then install the new stud by stacking washers on the new stud and tighten the lug till it pulls the new studs flange tight against the back side of the hub. remove lug and washers , reassemble .

May 25, 2011 | Honda CR-V Cars & Trucks

3 Answers

Need to get a wheel lug stud out of the wheel hub. there not enought room to pound it out from the another side it seems to me you have to remove the whole hub? yes or no.?


Dont remove the hub! Usually you can rotate the hub and find a spot that the stud will come out.Other option is to saw off and inch or so of the stud before you remove it.Then knock it out.Good luck!

Apr 20, 2011 | 1998 Chevrolet Monte Carlo

1 Answer

How to replace lug studs


You will need a special tool to press the lug studs in and out of the flange, or you can follow these directions;

First you will have to pound the broken lug stud(s) out of the wheel hub/flange, use a punch or a drift that is a little smaller in diameter than the lug stud, and be sure that you do not pound on the flange itself, then you will need a lug nut and about a half an inch thick of flat washers.

1. Insert the new lug stud through the wheel hub from behind so that the threaded end is facing out towards you and then put some grease on the threads.

2. Then slip the flat washers onto the lug stud followed by the lug nut, and run the lug nut down backwards with the flat end of the lug nut towards the flat washers to take up the slack and use plenty of grease on the threads.

3. Then using a breaker bar tighten the lug nut until it pulls the lug stud through the wheel hub and it is flush with the wheel hub.

Be sure that the amount of flat washers used will make up for any non-threaded part of the lug stud that might stick out past the wheel hub preventing the lug nut from pulling the lug stud all the way through the wheel hub, and basically you do not want the lug nut to run out of threads before it can pull the lug stud flush with the wheel hub.

Let me know if you require any further assistance.

Jul 31, 2010 | 1994 Honda Civic

1 Answer

I am wanting to replace the rear wheel studs that are broken. The wheel hub flange won't come off. Is there a special puller for this, do I need to apply more force or is there another method for removal?


You do not remove the wheel hub flange, just follow the procedure that I replied to earlier, and this is the procedure if you do not want to obtain a special tool for pressing the lug studs;

First you will have to pound the broken lug studs out of the wheel hub, then you will need a lug nut and about a half an inch thick of flat washers.

1. Insert the new lug stud through the wheel hub from behind so that the threaded end is facing out towards you and then put some grease on the threads.

2. Then slip the flat washers onto the lug stud followed by the lug nut, and run the lug nut down to take up the slack.

3. Then using a breaker bar tighten the lug nut until it pulls the lug stud through the wheel hub and it is flush with the wheel hub.

Be sure that the amount of flat washers used will make up for any non-threaded part of the lug stud that might stick out past the wheel hub preventing the lug nut from pulling the lug stud all the way through the wheel hub, and basically you do not want the lug nut to run out of threads before it can pull the lug stud flush with the wheel hub.

Jun 13, 2010 | 2003 Chrysler Town & Country

2 Answers

Studs for rear wheel mounting broken off. How are they repleced?


First you will have to pound the broken lug studs out of the wheel hub, then you will need a lug nut and about a half an inch thick of flat washers.

1. Insert the new lug stud through the wheel hub from behind so that the threaded end is facing out towards you and then put some grease on the threads.

2. Then slip the flat washers onto the lug stud followed by the lug nut, and run the lug nut down to take up the slack.

3. Then using a breaker bar tighten the lug nut until it pulls the lug stud through the wheel hub and it is flush with the wheel hub.

Be sure that the amount of flat washers used will make up for any non-threaded part of the lug stud that might stick out past the wheel hub preventing the lug nut from pulling the lug stud all the way through the wheel hub, and basically you do not want the lug nut to run out of threads before it can pull the lug stud flush with the wheel hub.

Jun 13, 2010 | 2003 Chrysler Town & Country

2 Answers

Broken lug nut how to replace lug nut studs


take off tire. remove old stud by hammering it out with a punch. put a socket behind axle plate so as not to break the plate. when replacing, just start stud from back by hand, then use a lug nut to pull it in tight. when tight replace tire!

Apr 14, 2010 | 1999 Oldsmobile Intrigue

1 Answer

How to remove a broken lug stud from a 98 Ford Escort?


Most studs are pressed in. Big hammer and punch and knock it out. If it doesn't move, get a bigger hammer.

May 19, 2009 | 2002 Nissan Sentra

1 Answer

Lug bolt on front drivers side wheel is broken & needs replaced. I'm doing the job.


Safely jack and support the vehicle,remove wheel and tire assembly,with a punch and ball peen hammer (and safety glasses) or just a hammer,carefully knock broken stud out of the hub,it will fall out the back.Now take new stud and spin the hub until you find a spot where it will insert into the hole from the backside.Start the stud through the hole from the backside of the hub.Now at this point,you are going to PULL the stud into the hub,but the threads must be protected from galling.I use Anti Seize compound and some flat washers.Liberally coat the threads of the new stud with anti seize compound to protect the threads,stack some flat washers on the stud,install the lug nut,and tighten by hand.The stud will pull into the hub some.Remove lug nut,and stack more washers on the stud,and repeat the tightening process.Repeat process until stud is fully seated.Now remove anti seize compound with brake cleaner or equivalent solvent.Reinstall wheel and tire,and call this job completed.Remember to rate this solution.Good luck.

Sep 01, 2008 | 2001 Honda Civic

Not finding what you are looking for?
1998 Acura Integra Type R Logo

Related Topics:

63 people viewed this question

Ask a Question

Usually answered in minutes!

Top Acura Experts

yadayada
yadayada

Level 3 Expert

77514 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you an Acura Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...