Question about 1988 Chevrolet S-10

1 Answer

How do u remove wiper arm from truck1988 chevy s 10

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 2,468 Answers

Its on a spline and after years you will need to put a block between the windshield and the arm and spray with penetrating oil then use some uplift force while wiggling,and possibly some leverage between the windshield and the arm to help loosen the arm from the spline

Posted on Jul 16, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I change wiper blades 2001 Chevy blazer


Open the cap at the end of the windshield wiper arm at the cowl of the Blazer. This will reveal the bolt that secures the wiper arm to the wiper linkage.
Unbolt the wiper arm using a 3/8-inch ratchet and socket. Place the bolt to the side, as you will reuse it later.
Pull the wiper arm up at the blade so that the blade of the wiper is pointing into the air. Then pull at the base of the arm, wiggling it slightly. It's a keyed gear, so it may take a little bit of workunderlined.png?1 to break it free, but with the right amount of wiggling, it will disengage.

Read more: How to Remove Chevy Blazer Windshield Wipers ' eHow.com http://www.ehow.com/how_6177302_remove-chevy-blazer-windshield-wipers.html#ixzz1B4pQJ39h
  • 3 Pull the wiper arm up at the blade so that the blade of the wiper is pointing into the air. Then pull at the base of the arm, wiggling it slightly. It's a keyed gear, so it may take a little bit of workunderlined.png?1 to break it free, but with the right amount of wiggling, it will disengage.

  • Read more: How to Remove Chevy Blazer Windshield Wipers ' eHow.com http://www.ehow.com/how_6177302_remove-chevy-blazer-windshield-wipers.html#ixzz1B4pJlPaV
  • 2 Unbolt the wiper arm using a 3/8-inch ratchet and socket. Place the bolt to the side, as you will reuse it later.
  • 3 Pull the wiper arm up at the blade so that the blade of the wiper is pointing into the air. Then pull at the base of the arm, wiggling it slightly. It's a keyed gear, so it may take a little bit of workunderlined.png?1 to break it free, but with the right amount of wiggling, it will disengage.

  • Read more: How to Remove Chevy Blazer Windshield Wipers ' eHow.com http://www.ehow.com/how_6177302_remove-chevy-blazer-windshield-wipers.html#ixzz1B4p1UYyB

  • 2 Unbolt the wiper arm using a 3/8-inch ratchet and socket. Place the bolt to the side, as you will reuse it later.
  • 3 Pull the wiper arm up at the blade so that the blade of the wiper is pointing into the air. Then pull at the base of the arm, wiggling it slightly. It's a keyed gear, so it may take a little bit of workunderlined.png?1 to break it free, but with the right amount of wiggling, it will disengage.

  • Read more: How to Remove Chevy Blazer Windshield Wipers ' eHow.com http://www.ehow.com/how_6177302_remove-chevy-blazer-windshield-wipers.html#ixzz1B4p1UYyB

    Jan 15, 2011 | 2001 Chevrolet Blazer

    1 Answer

    I have a 92 chevy S10 truck, how do you remove the wiper blades and arms?


    GM S10/S15/Sonoma Pick-Ups 1982-1993 Repair Manual Blade and Arm - REMOVAL & INSTALLATION
    (see Figures 1, 2 and 3)
    1. Matchmark the base of the wiper arm to the linkage. This will assure the arm is installed in the proper position. If the arm is being replaced, transfer the matchmark from the old component to the new one before installation. This can be done by placing the new arm on top of the old one and copying the mark.
    1bb2352.jpg

    Fig. 1: Removing the wiper arm using J-8966

    0234572.jpg

    Fig. 2: If no wiper arm tool is available, use a small prytool to depress the spring

    5227e24.jpg

    Fig. 3: With the spring released, pull the wiper arm from the linkage
    1. Most wiper arms are retained by a spring clip. Some are equipped with a release tab at the center which should be depressed to release the arm. If no tab is provided, use a small prybar or a wiper arm removal tool such as J-8966 to depress the spring and release the arm. Remove the arm from the vehicle.
    2. Some late model vehicles (all 1993 and some earlier models) are equipped with a wiper arm that utilizes a small release hole at the base of the wiper arm. If equipped, insert a 1 / 8 in. drift pin into the tool access hole to release the locking device and allow the arm to be easily pulled from the transmission. If necessary, use a gentle rocking motion to remove the arm.
    To install:
    1. Except for late model vehicles equipped with the tool access hole, align the matchmarks and gently press the blade over the linkage and snap into position.
    2. For 1993 vehicles (and earlier models equipped with the access hole on the arm) straighten the arm assembly and insert the pin. Align the arm with the linkage mark made earlier, then press down on the arm's head casting until it seats and locks onto the wiper pin. Remove the drift pin.
    3. Operate the wipers and verify proper alignment.

    Hope helps (remember rated this).

    Jul 08, 2010 | 1992 Chevrolet S-10

    1 Answer

    1988 Pickup: 1988 toyota pickup wiper arm removal????...


    Remove the cover located at windshield base with flatblade screw driver or other prying device. Remove retaining bolt, then while prying under wiper arm where it is attached to wiper motor shaft, wiggle wiper arm side to side and up & down. Don't be scared.

    May 18, 2010 | 1988 Toyota Pickup

    1 Answer

    1988 Taurus: how to change a 1988 ford Taurus wiper arm...


    USE A SMALL SCREW DRIVER TO PRY OUT THE WIPER ARM RELEASE LEVER WHILE LIFTING THE ARM UP TO DISENGAGE THE ASSEMBLY FROM SPINDLE.

    May 18, 2010 | 1988 Ford Taurus

    1 Answer

    I need to know how to remove a 1987 chevy s10's windshield wiper, not the arm but just the wiper. cant find a release switch and am thinking i need to force it off


    Use a small screwdriverslide it between the plastic of the wiper blade and the top of the wiper arm. There is a tab that holds the blade in place, you should be able to gently pull the wiper back off the arm.

    May 03, 2010 | 1987 Chevrolet S-10 Pickup

    1 Answer

    How do you remove the windshield wiper arms


    The wiper arms have a push in tab at the very bottom at the fitting that is pressed into the wiper linkage below the screen. Use a flat headed screwdriver to pry out the tab. Once out the arm can be pulled right off. Now you can remove the cowling screen

    Apr 07, 2010 | 1987 Chevrolet S-10 Pickup

    1 Answer

    What is the 94 Chevy Caprice Classic wiper arm


    heres a wiper linkage asm diagram, the wiper washers are on the hood or on the cover to deck,then the hose runs through the wiper arm to a nozzle, if you remove the arms you can lift cover enough to look at the hose to washer connection,also check hose to arm they often break there good luck.2d8c418.gif

    Mar 30, 2010 | 1994 Chevrolet Caprice Classic

    1 Answer

    How to replace the wiper motor on a 1988 Ford F-150


    1-remove wiper arms 2-remove cowl 3-undo linkage drive from wiper motor 4-remove elect.connection from wiper motor,remove mounting bolts,remove wiper motor.

    Apr 17, 2009 | 1988 Ford F 150

    1 Answer

    1984 chevy S10 windshild wipers


    at the arm remove the cap on end and their is a nut remove it 10 mm / Please rate my response thank you very much

    Jan 28, 2009 | 1984 Chevrolet S-10

    1 Answer

    Wipers seized- motor works. cant move blades more tham1=2 inches.


    you have to remove the whole wiper arm both sides...under hood remove 5 -5/16 screw from vent panel .. remove panel .. under panel on drivers side you will see where arm attach to wiper motor ..remove nut... then remove 3 bolts that hold wiper motor to firewall .

    Nov 29, 2008 | 1988 Chevrolet S-10

    Not finding what you are looking for?
    Cars & Trucks Logo

    187 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Chevrolet Experts

    Marvin
    Marvin

    Level 3 Expert

    81400 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22359 Answers

    Ronny Bennett Sr.
    Ronny Bennett Sr.

    Level 3 Expert

    6927 Answers

    Are you a Chevrolet Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...