Question about 2005 Jeep Wrangler

Open Question

How do to replace a 2005 Rubicon automatic Shifter & Cable?

How do you replace an automatic shifter and transmission shift cable on 2005 rubicon?

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 321 Answers

SOURCE: 2005 dodge magnum gear shifter

If the shifter is stuck in Park,most likely the shift interlock is malfunctioning.The interlock solenoid,or actuator,is mounted on the shifter,and locks or unlocks the shifter in Park postion based on whether your foot is depressing the brake pedal.The problem could be the brake pedal switch,the interlock solenoid,or the wiring between the two.Also check all your taillight bulbs,third brake light bulbs,or any bulbs involved in the brake lights circuit.I have seen a brake light bulb that was burned out,cause the same symptoms as yours,but it was a different make vehicle.

Posted on Jul 13, 2008

Ad
  • 1 Answer

SOURCE: Cruise control does not work

On my 05 Wrangler Unlt'd Ruby - The vacuum hose on the drivers side of engine had come off, which disengaged my Cruise and the actuator which determines whether my heater points to the vent, Defrost or feet. Put it back on and secure with a cable tie.

If it is like mine, you will then have idling problems, especially when coming to a stop. You will need to clean the throttle body because the engine has picked up **** through the open port while it was off. Directions for that exist on this site elsewhere.

All of these are easy - i hadn't worked on a car in >25 years and it took me 30 min.

Posted on Sep 16, 2008

pal03246
  • 726 Answers

SOURCE: Automatic Gear Shifter Light Burned Out

You shifter indicator bulb (194 bulb number) has burned out. Pretty easy and cheap fix. The top of the indicator has to be removed/lifted up and teh bulb needs to be replaced.

Posted on Oct 27, 2008

  • 6982 Answers

SOURCE: 1993 JEEP GRAND CHEROKEE AUTOMATIC TRANSMISSION

Likely you have a shift control module malfunction. Module is probably on the right side fender in the engine compartment. Check to see if you have one (some do and some dont... go figure...I've got a 91 & 95... I have about five different diagrams and NONE apply to my vehicles)

Posted on Dec 16, 2008

godtech
  • 51 Answers

SOURCE: shifter cable change out

YES IT WILL AND ITS EASY YOU CAN DO IT.

Posted on Jan 17, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1988 Dodge Ram 50 Automatic shifts into park reverse and neutral. But physically won't go into drive gears.


Disconnect shift cable from transmission linkage and try to manually put transmission in drive gear ( make sure wheels chocked/park brake on ). If transmission goes into drive gear, suspect a shift cable or shifter assembly problem. If you can't manually shift into drive gear by hand with cable disconnected, suspect internal transmission/shift linkage issue

Mar 10, 2016 | Dodge Cars & Trucks

1 Answer

How do i get a automatic transmission shifter unstuck from neutral between the two gates on a 2005 hyundai tucson gl


it looks like you have a problem with the shifting cable. release the cable from the transmission side and check functionality. replace or adjust .

Nov 29, 2015 | 2005 Hyundai Tucson

1 Answer

How do I REPLACE SHIFT CABLE


rtm? no symptoms so i must guess, ill say , cant shift. and is not park lock out causing that.
want to read the manual or me to you.'?
ill guess you.

http://www.jeep4x4center.com/knowledge-base/index.htm?utm_source=cj#service

click 1996 to 2001
it replaces like all cables do
detach both ends and remove it. if clamps seen those too.
what matters is adjustment is needed.

some have 2 cables, one to gear box and one to ignition switch.
Chapter 21, page 150 states
REMOVAL
(1) Shift transmission into Park.
(2) Remove shift lever bezel and necessary console
parts for access to shift lever assembly.
(3) Disconnect cable at shift lever and feed cable
through dash panel opening to underside of vehicle.
(4) Raise vehicle.
(5) Disengage cable eyelet at transmission shift
lever and pull cable adjuster out of mounting
bracket. Then remove old cable from vehicle.
INSTALLATION
(1) Route cable through hole in dash panel. Fully
seat cable grommet into dash panel.
(2) Place the auto transmission manual shift control
lever in "Park" detent (rearmost) position and
rotate prop shaft to ensure transmission is in park.
(3) Connect shift cable to shifter mechanism by
snapping cable retaining ears into shifter bracket
and press cable end fitting onto lever ball stud.
(4) Place the floor shifter lever in park position.
Ensure that the pawl is seated within the confines of
the adjustment gauge clip.
(5) Snap the cable into the transmission bracket so
the retaining ears are engaged and connect cable end
fitting onto the manual control lever ball stud.
(6) Lock shift cable into position by pushing
upward on the adjusting lock button.
(7) Remove and discard the shift cable adjustment
gauge clip from the park gate of the shifter.

easy?

Aug 25, 2015 | 1996 Jeep Cherokee

3 Answers

Why won't my transmission shift out of park and shifter moves freely ?


you will need to replace the shift cable from selector to transmission

Sep 30, 2014 | 2005 Chevrolet TrailBlazer

1 Answer

How do replace the shift cable for my 1993 caravan, where the cable connects to the lever by the transmission?


it coneaks to the shifter on the steering wheel and goes down to the trans. if u can tape together new one to old one and disconect by shifter and pull old one out as the new one follows behind. conect to shifter and trans adjust as needed and u should b done.

Sep 22, 2012 | 1993 Dodge Caravan

2 Answers

1991 Honda Civic DX Why am I able to push the car with automatic transmission while it's in park? The car won't start and run, either.


If the car rolls with the shifter in the park position and the starter will not engage the engine than the transmission is not in park. This could be caused by a bad shift cable. In order to confirm this you will need to find the area where the shift cable attaches to the transmission. While a helper runs the shifter through the gears check the linkage at the transmission to see if it is moving. If the linkage is not moving that there is a problem with the shift cable or the shifter. Some disassembly of the center council may be necessary to gain access to the area where the shift cable attaches to the shifter to see if it is still attached to the shifter. If it is and the shifter is moving the cable than the cable will need to be replaced. If the cable is moving the linkage at the trans than there is probably something wrong internally inside of the transmission. If you have any questions or need further help I will be happy to do what I can!

I’m happy to assist further over the phone at https://www.6ya.com/expert/jeremy_d728a59f986299fa

Sep 06, 2011 | 1991 Honda Civic

2 Answers

Car was put in park and would not shift into any other gear, the shifter just slides very loosely into the other gears. It's as if there is no resistence to the shifter when you are trying to shift. I...


sounds more like a gear selector cable.
kick down cable would normally be connected to the throttle somewhere and would not affect the shift lever

Feb 20, 2011 | 2005 Ford Taurus

3 Answers

Automatic gear shift in 94 toyota tercel stuck


what is stuck?

the linkage or the cable from the shifter to the trans.?

block the tires so the car can not roll away...
open the hood and remove the cable from the shifter on the transmission.
see if you can manualy move the shifter on the trans.
if that moves... you may need to replace the cable (shift linkage)

Feb 19, 2011 | 1994 Toyota Tercel

1 Answer

Reverse is not where it belongs, it is between reverse and neutral


you may have a bent shifter rod under your car. can you pull the rubber boot up on shifter and see if it has not came loose from the shifter inside? you will need to remove the screws that hold the cover on. on the floorboard. if the problems not there,it's on the shifter linkage rod. the bushings in the shifter rods may have gone bad or have been jammed by erratic shifting,or just every day useage.that was solution for manual shift transmission.[this is solution for automatic transmission] your shifter cable may only out of adjustment,or your shifter cable may have stretched due to cold weather or just worn. open your hood, this will take 2 people to work together.one to see the transmission shift on top of transmission,the other to shift the transmission. apply the emergency brake,engine off, shift the gears back and forwards from drive to park. does it look like the cable or linkage has play or slop in it? if it does you can adjust it by putting the car in park and then tighten the bolt on top of the cable,on the top of the transmission. hope this helps and thank you for choosing fixya.com

Jan 20, 2011 | Suzuki Reno Cars & Trucks

Not finding what you are looking for?
2005 Jeep Wrangler Logo

Related Topics:

124 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

Marvin
Marvin

Level 3 Expert

82331 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22382 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...