Question about 2000 Daewoo Nubira

1 Answer

I need to remove the ignition barrel to replace it how is this done

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 1,596 Answers



IGNITION LOCK CYLINDER AND SWITCH

Removal Procedure

  1. Disconnect the negative battery cable
  2. Remove the lower steering column cover panel by removing the screws.
  3. Disconnect the electrical connector for the immobilizer detection coil, if equipped.
  4. With the key in the ignition turned to the position designated ACC, remove the lock cylinder by pressing down the detent spring with a 2.5 mm alien wrench or other suitable tool, and pulling the lock cylinder out of the switch cylinder housing. 5. Install the lower steering column cover panel with the screws. Tighten the lower steering column cover panel screws to 3 Nm (27 inch lbs.).
  5. Connect the negative battery cable

Posted on Jul 16, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Key wont go into ignition


could some thing have been inserted into the ign switch ?if not there is a metal tab that is part of the cylinder lock mechanism which after time and use can break away and stop key going into the barrel,the ign lock barrel will need replacing , will need to be done at a repair shop as need key inserted to remove, so will need a strip down ,a specific technique to remove when key won't go into lock is needed to remove/fit new lock

May 10, 2014 | 1999 Mitsubishi Mirage

1 Answer

Key broken in ignition barrel


Any parts store will have torx bits, this will remove the bolts.

Jan 12, 2014 | Ford Festiva Cars & Trucks

1 Answer

Replace ignition barrel with a snapped metal intrument in it


you can try to remove said instrument with plyers, easiest way for me to fix a car like that is to replace the whole dang steering column. To replace the keyswitch only, check out this video, it applys to your car too! http://www.youtuberepeater.com/watch?v=oFsQhk-QQS8&name=toyota+corolla+ignition+lock+cylinder+and+key+switch+replacement

Dec 16, 2013 | 1996 Toyota 4Runner

1 Answer

How do i remove the entire iognition switch assemble in mitusbishi gallant 1991


Hi Bruntwood, Disconnect the battery, and then unscrew the screws fitted underneath which hold the plastic cowling surrounding the steering column and then remove the two halves. Disconnect the electrical socket from the plug and then identify the four blind bolts holding the saddle of the ignition barrel and switch. There are a few ways of removing those bolts, but the easiest is to tap them out with the correct sized cold chisel. Once removed the ignition barrel and switch can then be removed and replaced. Assembly is the reverse procedure. Regards and have a happy new ignition barrel and switch and new year. John

Dec 31, 2012 | Mitsubishi Cars & Trucks

1 Answer

How to remove barrel,demonstration


remove the steering lock barrel can only be done with the original key and the ignition in the acc position .this can be done in situ but some motors like VW you have to drill the hole to push the pin in so you need to know where it goes and to get to it you have to remove the steering column

Oct 13, 2012 | 1998 Holden VT Commodore

1 Answer

Hello again - thank-you for your advice on my key/ignition problem- advising replacing the lock set- however its sunday, I am stuck on a road in spain with the window open and badly parked - is there


y but you will require tools and a knowledge of the vehicle. You will need to remove the plastic surround of the steering column and the covers under the dash. When you can see the back of the ignition assembly you will see round dome shaped bolts holding on a clamp which secures the assembly in place. These will need to be removed using a cold chisel or something which can cut into the domes so th the domed bolts can be unscrewed and the ignition barrel removed. Once that has been done, unscrew the ignition swith from the end of the barrel and operate it with a screw driver. You will be able to turn on the ignition and drive the car. Best regards John.

Jun 17, 2012 | 2003 Land Rover Freelander

1 Answer

KEY STUCK IN THE IGNITION


just a guess on this one , some ignition barrels have a button underneath the key barrel , and to remove key you must push this in and turn key back one more klick away from start direction .

i am hoping that original key is in ignition , you can get ignition barrel replaced with new keys , but some steerng parts need dissasembling .
and some are pains to remove .
hope it was this simple !

Nov 10, 2010 | 2002 Isuzu Axiom

1 Answer

The starter (ignition) switch does not return automatically to the "on" position after starting. Does this mean I have to replace the switch or can it be repaired?


it is the barrel at the rear of the ignition switch, you do not need to replace the whole of the ignition switch just the part on the back if you remove the stearing cowling and look behind the ignition barrel you will see either a white or black ( might be any colour though) item with wires going into it, all that is needed is that part to be replace, just unplug the wireing part and remove the ignition box from the back of the barrel and replace, hope i explained that correctly for you

Feb 02, 2010 | 1994 Saab 900

1 Answer

I HAVE A MERCEDEZ 190 AND THE KEYS ARE NOT TURNING IN IGNITION BARREL NOW THE STEERING IS LOCKED ALSO I HAVE TAKEN OUT IGNITION BARREL WITH STEERING COLOUM. i WOULD LIKE TO DISINGAGE THE IGNITION BARREL...


it is better to buy a new ignition barrel.it takes a special socket to get the screws out, once the screws are out they do not need to be replaced.buy new barrel,disconnect negative battery cable,disconnect wires from barrel assembly, remove barrel from colum. first take vin# to dealership parts department to get correct barrel assembly, the keys with new assembly will fit doors and trunk

May 19, 2009 | 1993 Mercedes-Benz 190

1 Answer

Key's snapped off inside ignition


Hi I would suggest you ring the Automobile association, and see whether one of their mobile mechanics can solve your problem. extracting a car key from the barrel may be more difficult than it appears. He, the mobile man may have done it before and have the right tools for the problem.

May 30, 2017 | 1995 Volkswagen Passat

Not finding what you are looking for?
2000 Daewoo Nubira Logo

786 people viewed this question

Ask a Question

Usually answered in minutes!

Top Daewoo Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

yadayada
yadayada

Level 3 Expert

78267 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8836 Answers

Are you a Daewoo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...