Question about 1998 Chrysler Concorde

1 Answer

My 98 concorde will turn off sometimes when reaching a stop or slowing down. It starts back on but I dont know the problem and how to fix it. I was told it could be a sensor.

Posted by Anonymous on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 10,865 Answers

Begin by doing these two things. change the fuel filter and treat your fuel with a product called seafoam, available at most auto parts stores. J.

Posted on Jul 16, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

When I first start driving the transmission work fine ,then when I slow down it shifts into 2nd. and won't shift up again. So i stop the car , start it again and then it shifts fine again until I slow down...


I was told by a Chrysler tech that it's the shift solenoid located in the trans. pan. There are 4 of them and you have to have it checked to see which one. You don't want to replace all 4. About $80.00 at a dealer! Mine does the same thing. 2004 Concorde lxi.

Nov 21, 2010 | 2000 Chrysler Concorde

1 Answer

My 1997 Chrysler Concord idles at 2500 to 3000 rpm when first started and when it warms a little it idles at 2000 rpm and stays there. When I start it right after I turn it off, it starts at 2500 rpm then...


Maybe a short to the TPS or something shorting it out. There's also the IAC that really controls the idle but usually it will cause the RPM's to go up and down a little erratic if bad. The MAF sensor can cause major problems as well but since you already swapped the TPS and it helped and then stopped I would focus on that sensor and especially it's wiring to and from the ECM. Be careful with the sensor signal wire to the ECM can blow it if more than 5v passes or spikes.

Sep 03, 2010 | 1997 Chrysler Concorde

1 Answer

2001 Chrysler Concorde lxi randomly stalling while slowly dow to stop or turn. Will usually crank back. This car will sit and idle for ever but when you drive it for 10-15 minutes and slow down to stop or...


Check the fuel filter on car for a restriction. Check the air filter for a restriction(dirty). also check the IAC valve (idle/air/control) located on the side of the throttle body. To check the iac valve, start the engine and disconnect the electrical plug from the iac. Listen for a change in the idle of the engine. then reconnect the plug to the iac valve and turn on the a/c and listen for the engine idle speed to change. If not then replace the iac valve. Hope this will help you.

May 12, 2010 | Cars & Trucks

1 Answer

1996 Toyota Camry Stalls when slowing down/stopped


Your carb may need cleaning. I had the same problem with my Astra. If not then there is too much air getting into the engine.

Jun 05, 2009 | 1996 Toyota Camry

1 Answer

Transmission automatically shifts to low at idle


after my 2003 chrysler concorde is warm I slow down from the hwy and right before I stop my car shifts to LOW gear and stays there until I turn my car off and start it.

May 05, 2009 | 2003 Chrysler Concorde

1 Answer

98 chrysler concorde wont start, and when it does, it bogs down


on the throttle is a valve/sensor with a carbon track in it and i think it needs changing .not a cheap thing

Dec 30, 2008 | 1998 Chrysler Concorde

1 Answer

My gauges and heat dont work on my car and the check engine light comes on


This may be related to a loose battery cable or alternator concern, low voltage can cause these concerns as well as an alternator problem, also this could be related to the body control module, Go to a Kragen, Auto Zone and have the battery and alternator tested, it's free, let me know the results.

Nov 17, 2008 | 1996 Chrysler Concorde

1 Answer

I have a problem with my chrysler concorde 04


hi susan its pierre come back with the code i look foward to hearing from you pierre

Jun 27, 2008 | 2004 Chrysler Concorde

Not finding what you are looking for?
1998 Chrysler Concorde Logo

Related Topics:

87 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

Marvin
Marvin

Level 3 Expert

83096 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22382 Answers

chargerhp
chargerhp

Level 3 Expert

814 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...