Question about Hyundai Motor 2003 Elantra

2 Answers

How do I remove front rotors from a 2003 hyundai elantra

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

You have to put two screws in the holes on the rotors and drive the rotor off

Posted on Jul 27, 2010

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Teacher:

    An expert who has written 2 tips or uploaded 1 video tip.

  • Expert
  • 123 Answers

First jack the front end up. Then remove the wheels. Then remove the calipers. Then the rotors should fall right off the car into your hands. They are not pressed on or hubs

Posted on Jul 16, 2010

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 840 Answers

SOURCE: Adjusting the low beam headlight

its all the same the headlight is a complete unit you adjust both/ look for screws behind the headlight one each side one is for horizontal annd the other is for vertical Please rate my response thank you very much

Posted on Jan 31, 2009

  • 105 Answers

SOURCE: 2003 hyundai elantra brake rotor removal

if there are screws holding rotor on remove them.you can drill the heads of if you need to they realy dont do any thing remove caliper bracket if its in the way some rotors have drilled and taped holes in them if yoursn do thread bolts into them and tighten down this will put pressure on the rotor to pushit of hub if not use large hammer and hit the face of rotor between studs to loosen it up also dont be afraid to use lots of wd40 of so sort of penatrating oil on them to help loosen them up let me know how you make out

Posted on May 31, 2009

GARYca
  • 672 Answers

SOURCE: 2003 Hyundai Elantra

NO. These models do not have warnings on the transmission failure. There is warnings only when the transmission encounters electrical component failure, overheating(some cars), low fluid. Usually the warning is the O/D flashing light, or a seperate transmission light. Hopefully this helps

Posted on Jul 21, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replace left front fender


Replace left front fender - Fixya

www.fixya.com/cars/t26028082-replace_left_front_fender
Dec 29, 2015 - replace left front fender - Hyundai Motor 2003 Elantra question. ...Question about Hyundai Motor 2003 Elantra. Open Question ... How do i remove left front fender clip on a Lincoln ls 2002? Jan 04, 2015 ' 2002 Lincoln LS.

Replace 2003 hyundai elantra front passenger outside door ...

www.fixya.com/cars/t17348691-replace_2003_hyundai_elantra_front
Mar 26, 2013 - Question about Hyundai Motor 2003 Elantra. Open Question.Replace 2003 hyundai elantra front passenger outside door handle. Need to replacebroken exterior door handle on front passenger .... replace left front fender.

Dec 29, 2015 | Hyundai Motor 2003 Elantra

1 Answer

How to replace struts on front of 2003 hyundai elantra


Are you replacing the complete strut assembly with the coil spring and strut mount already attached? Because if not, you'll need a coil spring compressor.

Dec 30, 2010 | Hyundai Motor 2003 Elantra

1 Answer

I need to know about changing the front rotors on a 1998 elantra? Icannot get the rotor off to replace it.


Sometimes the rotors can get rusted on there really good. You'll need penetrating oil and a big hammer to get them off if they are stubborn.

Sep 25, 2010 | 1998 Hyundai Elantra

1 Answer

I want to change the front rotors on a 2003 elantra and what do I need?


mcdevito75 here, You"ll need a sturdy jack to lift the car, you"ll need the tools to lift the brake calipers off the rotor, in short let your local shop change the rotors. If you try and get stuck some how now you have to tow the car and have the rotors replaced.

Jun 17, 2010 | Hyundai Motor 2003 Elantra

1 Answer

2003 hyundai elantra brake rotor removal


if there are screws holding rotor on remove them.you can drill the heads of if you need to they realy dont do any thing remove caliper bracket if its in the way some rotors have drilled and taped holes in them if yoursn do thread bolts into them and tighten down this will put pressure on the rotor to pushit of hub if not use large hammer and hit the face of rotor between studs to loosen it up also dont be afraid to use lots of wd40 of so sort of penatrating oil on them to help loosen them up let me know how you make out

May 31, 2009 | Hyundai Motor 2003 Elantra

1 Answer

2005 elantra need answer on removing rotors


REMOVAL:
Loosen the wheel nuts slightly. Raise the front of the vehicle, and make sure it is securely supported.
Remove the front wheel and tire from front hub.
Remove the split pin, then remove castle nut and washer from the front hub while applying the brake.
Remove the caliper mounting bolts, and hang the caliper assembly to one side. To prevent damage to the caliper assembly or brake hose, use a short piece of wire to hang the caliper from the undercarriage.
Remove the wheel speed sensor from the knuckle.
Disconnect the tie rod end ball joint from the knuckle using the special tool (09568-34000).
Remove the split pin.
Remove the castle nut.
Disconnect the ball joint from knuckle using the special tool (09568-34000).
Remove the lower arm ball joint mounting bolts
Remove the strut lower arm mounting bolts
Remove the hub and the knuckle assembly


INSTALLATION:
Reverse the order of the removal procedure.

May 23, 2009 | 2005 Hyundai Elantra

2 Answers

Need power window diagram for 2000 hyundai elantra


is this what your looking for??
Front Door Glass:
36c72f3.jpg

Apr 25, 2009 | 2003 Hyundai Tiburon

1 Answer

Replacing studs


sometimes they just get stuck, which a big soft blunt hammer will cure with a good hit , or maybe you missed these assembly line screws ? there may be 2 of them on each rotor .

cd37a74.jpg

if there just stuck , try some penetrating oil / spray , and spray around the inside circle where the rotor meets the hub , let it penetrate ,give it a good smack with a hammer and a piece of wood so you don't damage the rotor .

Jan 10, 2009 | 2004 Hyundai Elantra

1 Answer

How do you get rotor off 2003 hyundia elantra


hi from uk not sure if same as uk hyundai's but here goes ? if you remove wheel do you see two countersunk posi screws between studs that appear to hold rotor ?? if so then you will have to first remove the brake caliper assy by unbolting from the rear of caliper two 13 mm spanner/socket ? then you remove the two bolts that secure the carrier that the caliper bolts to 17 mm spanner/socket now you can remove the two contersunk screws then you may have to tap the rotor off the hub from rearuse a wire brush to clean up/away all rust/dust from caliper and carrier assys b4 refitting (take precautions from breathing dust) i assume you are fitting new pads ?? reassemble carrier then b4 fitting pads smear a light coating of copper grease on the rear of pad (metal side ) this prevents squealing on brakes then fully reassemble then b4 fitting wheel? bleed the brakee caliper a couple of pumps should expel dirty fluid then fit wheel carry out same proceedure on other brake assy as above fully then b4 you move car pump brake to ensure pedal is firm you will find that bleeding brakes will make pedal firmer as the old fluid becomes compressable due to heat/moisture absorbsion over time and heat from brakes is transferred to fluid via caliper piston understand?? that is why alway policy to bleed/flush brake fluid at least two yr interval this reduces spongy brake pedal hope this is all clear 4 you to follow best wishes for new year and hope you update on how you go on??

Jan 10, 2009 | 2004 Hyundai Elantra

1 Answer

Front breaks 2001 hyundai elantra


Make sure the backing plate is not bent and contacting the rotor.

Jun 30, 2008 | 2001 Hyundai Elantra

Not finding what you are looking for?
Hyundai Motor 2003 Elantra Logo

Related Topics:

341 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7688 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...