Question about 2005 Jeep Liberty

1 Answer

How to change brake pads on a 2005 jeep liberty

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 27 Answers

Remove wheel useing 3/4 or 19mm soc 13mm rachet wrench or soc will remove the calipher use a small bunge or a piece of wire to hang calipher up do not let calipher hang by hose.you can now change pads, if you want to change rotor also you need a 21mm soc to remove bracket that holds pads. reverse procedure and you are done.

Posted on Aug 31, 2010

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

michigan man
  • 3533 Answers

SOURCE: how to replace rear brake pads on 2005 jeep liberty

put the back of car on jack stands and secure the front tires so it does not roll and then remove the bolts off the back of the caliper there is normally two one at top and one at bottom and spray it with some kind of oil for rust and make sure you have the right size socket before you try to loosen them and once caliper is off and the old pads removed take one of the old pads and squeeze the piston on the caliper back in by using a "C" clamp and also remove some of the brake fluid from the master cylinder before you do this put the new ones back on and check the brake fluid and make sure it is full and then pump the brakes to make sure you have a good pedal also put some "No Squeak" brake stop on the back of the pads so they don't squeak they will have that where you buy the pads from

Posted on Mar 01, 2009

  • 249 Answers

SOURCE: 2005 jeep liberty brake lights will not work. I

brake pedal switch, get a wire, unplug plug, bridge circuit and check lights.
plug and switch is high up on the brake pedal not normally easy to get to.

Posted on Aug 15, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace front rotors 2005 jeep liberty


Hi Wayne, I'm glad to help!

You'll need to support the vehicle on safety stands. Then take off the front wheels, Then take off the calipers that hold your brake pads. Then take off the bracket that the caliper is bolted too. Then remove the rotor. I suggest replacing the pads as well and be sure to clean the rust from where the pads rest on and make sure they slide easy back and forth, this will help in a longer life for the pads. Hope this helps and have an awesome day Wayne.

Oct 29, 2012 | 2005 Jeep Liberty

2 Answers

Abs light stays on in a 2005 jeep liberty


check brake fluid level ,worn pads, this can cause light to come on disconnect negative battery cable whait 2min and reconnect battery this will reset abs controller.

Aug 17, 2010 | 2005 Jeep Liberty

1 Answer

Changed rear brake pads have drag on brakes. Old pads were 10months old and were 80% worn fronts were ok


possible sticking calipers or binding parking brake cables or bad rear brake hoses

Feb 21, 2010 | 2005 Jeep Liberty

1 Answer

I drive a jeep liberty renegade 2005 model break and tail lights


check brake switch under brake pedal... if not working change it..

Dec 30, 2009 | 2005 Jeep Liberty

1 Answer

2005 jeep liberty brake lights will not work. I


brake pedal switch, get a wire, unplug plug, bridge circuit and check lights.
plug and switch is high up on the brake pedal not normally easy to get to.

Aug 15, 2009 | 2005 Jeep Liberty

1 Answer

How to test if bearings need replaced 2005 jeep liberty


Was the Rotors turned on the last front brake Service?....Sounds like uneven rotors in front

Jun 09, 2009 | 2005 Jeep Liberty

1 Answer

How to replace rear brake pads on 2005 Jeep Liberty


put the back of car on jack stands and secure the front tires so it does not roll and then remove the bolts off the back of the caliper there is normally two one at top and one at bottom and spray it with some kind of oil for rust and make sure you have the right size socket before you try to loosen them and once caliper is off and the old pads removed take one of the old pads and squeeze the piston on the caliper back in by using a "C" clamp and also remove some of the brake fluid from the master cylinder before you do this put the new ones back on and check the brake fluid and make sure it is full and then pump the brakes to make sure you have a good pedal also put some "No Squeak" brake stop on the back of the pads so they don't squeak they will have that where you buy the pads from

Mar 01, 2009 | 2005 Jeep Liberty

1 Answer

Troubled brakes


TAKE IT TO THE DEALER, SINCE VEHICLE HAS ABS SYSTEM . THE BRAKES MAY NEED TO BE BLEED WITH DRB/SCANNER. OR YOU MAY HAVE LINES CLOGGED.

Dec 30, 2008 | 2005 Jeep Liberty

Not finding what you are looking for?
2005 Jeep Liberty Logo

Related Topics:

455 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...