Question about 2001 Oldsmobile Aurora

1 Answer

Low oil preasure light binking on and off then going out on 2003 olds alero 3.4 oil is full

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    New Friend:

    An expert that has 1 follower.

  • Expert
  • 120 Answers

Probably the sending unit but it is safer to have the oil pressure checked at the rpm and temperature that this occurs

Posted on Jul 16, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Oil pump been replaced, knock senser and oil sending unit. oil light comes on and load ticking ,when its cold started on my 98 nissan altima


Go back to where you got the work done if you can.If not then i would get the oil preasure checked as the low light tells me the preasure is below 8 psi and the ticking is from the lash adjustors at the tappets verifys low preasure too.

Nov 27, 2012 | 1998 Nissan Altima

2 Answers

How do i reset the oil change light in a 2003 olds alero


turn key on (dont start engine) floor gas pedal 3 times 1,2,3. turn key off, now start engine it should go off, if not try it again.

Aug 03, 2011 | 2003 Oldsmobile Alero

1 Answer

How do you reset the change oil light on a 2003 Olds Alero


2 ways turn key on till the acc position remove plastic cover edge of the dash past air vent on drivers side theres a red reset buton hold it till resets n it also resets lower tir pressure monitor light if that comes on .... n u can turn key to all accessories comes n soon u turen the key press gas pedal to the floor n release 3 times

Jul 18, 2011 | 2003 Oldsmobile Alero

1 Answer

I have a 97 Pontiac Sunfire GT 2.4 DOHC that I just completed the head gaskets on due to major external leakage, now that is done though I have an low oil pressure light on! I can't for the life of me...


when doing headgaskets on thses it is very important that no debri falls into oil hole when cleaning or dissamebleming,also the headgaskets were installed correctly!!. check the preasure with the gauge and go from there,if it does have low preasure then something may have gotten into oil system, also you did change the oil after head job. if oil preasure is low and theres no knocking from engine then put a oil pump in in, most of the time its a bad oil preasure switch.good luck

Feb 27, 2010 | 1997 Pontiac Sunfire

2 Answers

Oil light on


first make sure oil level is up, then check or just replace oil preasure switch, if light still comes on, have your oil preasure tested, could be low oil preasure or electrical problem start there. good luck.

Oct 29, 2009 | 1998 Dodge Intrepid

2 Answers

Oil light flashing occasionally


It could be a faulty oil sending unit, but it would be advisable to have the oil preasure checked with a mechanical guage to determine if it is a sending unit or low oil preasure. Oil preasure low enough to allow the light to come on is low enough to possibly cause major engine damage.

Jul 06, 2009 | 1995 Toyota Previa

1 Answer

No oil preasure


First check the oil level. Do this on a level surface. Make sure it's close to the full mark, or in the operating range on the dipstick.
Next check to see how old the oil is. Is the vehicle well past it's scheduled oil change?
If the above checks out, then I suggest the oil pump is bad. Oil light being on, and noisy hydraulic lifter noise is directly related to low oil pressure. The oil light should come on at 3 lbs of pressure.

Rule of thumb is 10 lbs. of pressure for every 1000 Rpm.

Vehicles have a by-pass valve in the oil system. This comes into play when the filter is clogged up. The oil flow goes past the filter.

This by-pass valve is usually located in the engine block, where the filter attaches. It's up in the block itself. Depends on the vehicle, as to whether this statement hold true. There are many designs for an oil system.

Apr 09, 2009 | 1998 Ford Escort

2 Answers

2003 alero dash light won't shut off


Sounds like either a bad ignition switch or a back feeding circuit. Try unplugging the ignition switch to see if the lights go out. If they do, replace the switch. If they don't, post to tell me.

Mar 06, 2009 | 2003 Oldsmobile Alero

1 Answer

Resetting oil change dash light


Turn ignition key to the on position (with engine off). Depress accelerator pedal 3 times. Oil change light should blink and you should here a beep, light will go out. Turn ignition key off.

Nov 30, 2008 | 2004 Oldsmobile Alero

Not finding what you are looking for?
2001 Oldsmobile Aurora Logo

170 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

76051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8265 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...