Question about 1997 Chevrolet S-10 Pickup

2 Answers

Do i have to pull the motor out of a 1997 chevy s-10 to remove the transmission?

Posted by on

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 82 Answers

That is called an ENGINE NOT A MOTOR...Not as long as it is situated front to rear and not fender to fender (sideways Engine) it is a lot easier to do it with the engine removed, but UNLESS I was going to do some work. on the engine it would be redundant..

Posted on Jul 16, 2010

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 6,826 Answers

Removal & Installation To Remove:
Transmission mounting on 2.2L engines do i have to pull the motor out of a 1997 chevy - 88457g33.gif

Transmission mounting on 4.3L engines 88457g34.gif

  1. Disconnect the negative battery cable.
  2. Raise and support the vehicle safely using jackstands.
  3. Drain the transmission fluid.
  4. Remove the driveshaft from the transmission (2WD) and transfer case, if equipped (4WD or AWD).
  5. Support the transmission with a suitable transmission jack.
  6. Remove the shift cable from the transmission control lever and bracket.
  7. Remove the nut and washer securing the transmission mount to the crossmember.
  8. Remove the bolts and washers securing the mount to the transmission.
  9. Disconnect the exhaust pipe from the exhaust manifold(s).
  10. If equipped, remove the bolts securing the converter pan cover to the transmission.
  11. Remove the 3 bolts securing the torque converter to the flywheel.
  12. Remove the bolt, clip, and strap securing the three fuel lines and transmission vent hose to the transmission case.
  13. Remove the bolts and nut securing the transmission to the engine.
  14. Remove the oil filler tube and seal from the transmission.
  15. Disconnect the transmission cooler lines from the transmission. Plug the lines and the ports in the transmission.
  16. Unplug the wiring harness connectors from the transmission.
  17. Inspect for any other wiring, brackets etc. which may interfere with the removal of the transmission.
  18. Since the transmission acts as a rear engine mount, properly support the rear of the engine with an underbody support of other suitable support before attempting to remove the transmission. Otherwise the rear of the engine may pitch downward and components on the rear of the engine and on the firewall may be damaged.
  19. Remove the transmission from the engine by pulling the transmission rearward to disengage it from the locator dowel pins on the back of the block. Carefully lower the transmission from the vehicle. Use care that the torque converter does not fall out of the front of the transmission

Posted on Jul 16, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you pull out a 2005 Envoy GMC automatic transmission


I'm linking a YouTube video of a transmission/transfer case removal from a GM rwd/awd/4wd vehicle. The exact steps may not be the same for your Envoy, but you will get a general idea of what is involved. If you want step by step instructions, get a repair manual (Haynes, Chilton, Motor, etc) from your local auto parts store. How To Remove Transmission Transfer Case From GMC Sonoma Chevy 10 Blazer...

Mar 17, 2017 | 2005 GMC Envoy

1 Answer

What do I need to install a 2007 LS Chevy 5.3 L in a 1997 Chevy 1/2 ton pickup


You need the bolt hole alignment from the transmission to see if it will work. Certain transmissions only align with certain motors. Next is you'll probably need to transfer all the electronics, a 2007 engine control computer is most likely highly advanced compared to the 1997 computer. Then there's the questions of will the transmission shift correctly to match the engine RPMs.

Jul 26, 2016 | Cars & Trucks

1 Answer

How many quarts of transmission fluid does it take when you have a transmission flush done to a 1997 chevy lumina


7 quarts when pan drop 10 for an over haul page 6-64 of owners manual https://www.manualowl.com/am/Chevrolet/1997-Lumina/Manual/295 1997 Chevrolet Lumina Owner Manual

Aug 26, 2015 | Cars & Trucks

1 Answer

Im having trouble with my 1997 Chevy S10 transmission, the engine light is staying on, the transmission is shifting hard, I checked with my part store & they gave me a code within the transmission, the...


Google the code
OBD P1870
You got slipping I think your going to
be pulling it out & rebuilding it unless you
only drove ten miles with it doing so.
Lots on Google & You Tube Video including
seeing the code,the problem & the rebuild to resolve

Aug 08, 2013 | 1997 Chevrolet S-10 Pickup

1 Answer

Pulling the engine on a 1997 chevy z71


Transfer Case --first
Trans-second
Motor -third

Apr 01, 2013 | 1997 Chevrolet K1500

1 Answer

Do i have to pull engine to change oil pump on 1997 chevy s10 4.3L


if you can get oil pan off ,no you may have to unbolt motor mounts and lift engine up to get clearance.

Oct 03, 2012 | 1997 Chevrolet S-10 Pickup

1 Answer

Can a engine be removed from the top on a 1997 chevy venture


yes but you need to remove the transmission first and keep it on a harness to a lift as you remove the motor mounts.

Feb 04, 2011 | 1997 Chevrolet Venture

1 Answer

Removal procedure of oil pan for a 1997 chevy


To remove the engine oil pan either the engine has to be lifted all the way off of the motor mounts and the oil pan should just clear the flex-plate and transmission, or the front axle dropped down out of the way, or the transmission and flex-plate will have to be removed.

Usually if the engine can be lifted enough to fit a piece of 2x4 wood between the motor mounts and the frame then the oil pan will usually just have enough clearance to be removed from the rear and the oil pan should just clear the transmission and the flex-plate. Also, be sure to check that the fan blade does not damage the fan shroud when lifting the engine.

Let me know if you require any further assistance.

Jul 26, 2010 | 1997 Chevrolet Tahoe

1 Answer

Flex plate or terk converter on a 1997 Chevy Blazer for sell


Fly wheel or torque converter,either way your pulling out the transmission,very costly!

Nov 25, 2009 | 1997 Chevrolet Blazer

Not finding what you are looking for?
1997 Chevrolet S-10 Pickup Logo

509 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7772 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...