Question about 1998 Dodge Ram 1500 4WD

1 Answer

Torque spec. on bearing cap bolts on front diff on 98 dodge ram 1500

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 68 Answers

80 ft lbs.

Posted on Jul 16, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is the tighteing sequence on a 97 5.2 dodge ram 1500 connecting rods


First thing to do is use plasti guage in the inside of each bearing cup, tighten to spec and then remove it, measure the expansion of the plasti gauge to see if the clearance is within specs. Apply assembly grease and reassemble if ok. Two bolts on a bearing cap don't have a sequence to speak of. You finger tighten them both to the same point. Get a torque wrench and set it to half of the final value, tighten one, tighten the other, reset the wrench to final value, tighten one, tighten the other.

Jan 27, 2017 | Dodge Cars & Trucks

1 Answer

How much torque for each head bolt in a 2004 Dodge ram 1500 3.7 liter


Install the cylinder heads. Use new gaskets and tighten the bolts, in sequence, as follows:
  1. Step 1: Bolts 1-8 to 20 ft. lbs. (27 Nm)
  2. Step 2: Bolts 1-10 verify torque without loosening
  3. Step 3: Bolts 9-12 to 10 ft. lbs. (14 Nm)
  4. Step 4: Bolts 1-8 plus 1 / 4 (90 degree) turn
  5. Step 5: Bolts 9-12 to 19 ft. lbs. (26 Nm)


26002143-2qxw3km0vcnqu3setvnduoab-2-1.gif

Dec 10, 2015 | Dodge Cars & Trucks

1 Answer

What are torque specs on 1965 ford 7 and 1/4 inch rear


I have a '68 Motor's manual (goes back to'58) the only rear end specs I can find are for the pinion nut (140 ft. lbs.)
pinion preload: 17-27 in. lbs. w/integral carrier or 22-32 in.lbs. w/ removable carrier. Tightening the carrier bearings isn't so much a torque setting but more or a tightening procedure. Theses specs are done during the rebuild so I wonder if you're asking about the bearing caps or bolts that hold the diff. to the axle housing? I could not find a spec. for bolt torque. Since the bolts that hold it in (if that is what you asking about) are not a bearing adjustment, you can go with a generic torque based on bolt size. Again, I'm not sure what component, or bolts it is you are asking for torque specs on.

Sep 17, 2014 | Cars & Trucks

1 Answer

Need torque specs for front wheel bearing on 2004 dodge 3500 dually


The hub bearing retaining bolts are 150 ft. lbs the center axle nut primary torque 135 ft.lbs rotate 5-10 times increasing torque by 50 ft.lbs until final torque of 265 ft.lbs is reached

Mar 23, 2014 | 2004 Dodge Ram 3500 Truck

1 Answer

Front and back berring dissassembly of differential 2001 dodge 1500


For the rear diff., remove the driveshaft, brake drums, diff. cover, remove pinion flange nut, move diff carrier to access side gear retainer bolt and remove bolt, slide side gear pin out and push axles in to remove axle retainers and remove axels. Mark carrier bearing retainers, spin bearing retainers to loosen carrier for removal. Remove carrier, remove pinion out of diff case, then r&r bearings. Any shims should be replaced in their original location for depth and pinion to ring contact.

Feb 05, 2011 | 2001 Dodge Ram 2500 Truck

2 Answers

Front Hub Bearing Torque specs to complete replacement


THE LUG NUT TORQUE SPEC - 140FT/LBS\
CALIPER MOUNT - 80FT/LBS
CALIPER BRACKET 129FT/LBS
AXLE NUT 177FT/LBS

Apr 24, 2009 | 2003 Chevrolet Silverado 1500

2 Answers

99 dodge intrepid specs


Inner main bearing cap bolts:
Torque to 15 ft-lbs, then rotate an additional 1/4 turn

Outer main (windage tray) bearing cap bolts:
Torque to 20 ft-lbs, then rotate an additional 1/4 turn

Main bearing cap cross bolts:
Torque to 250 in-lbs or 20.83 ft-lbs

Connecting road bearing cap nuts:
Torque to 20 ft-lbs, then rotate an additional 1/4 turn

Apr 21, 2009 | 1999 Dodge Intrepid

2 Answers

98 dodge ram 1500 4x4 wheel bearing replacement


Yes those are bolts. You remove those from the back side. This takes a while sometimes. If you can't get them by reverse alone, try hitting them with impact in forward for a hit or two to brake it loose a little. If the new hub comes with new bolts, don't be afarid to brake them. PS, after those bolts are removed, don't forget to remove the nut on the axle shaft. You may also need to use an air hammer to help remove old hub after bolts are removed.

Sep 04, 2008 | 1998 Dodge Ram 1500 4WD

Not finding what you are looking for?
Cars & Trucks Logo

334 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6918 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...