Question about 2005 Pontiac Montana

2 Answers

2003 remote control for 2005 van?

Hello,
I have a 2005 Pontiac Montana. It didn't come with a remote control (since it's a used van). The company that we bought it from gave us a 2003 remote control to try. It doesn't seem to work. Is there any way, I can use a Universal Remote? Say from Wal-Mart, Best Buy etc? If so, what make is the DVD player? Thank you so much for all your help!!

Posted by on

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Pontiac Master
  • 6,826 Answers

Transmitter Programming
If you lose a transmitter, program the old and new transmitter(s) into the remote control door lock receiver's memory. Up to 4 transmitters may be programmed.


Important
Once the remote control door lock receiver enters the programming/diagnostic mode, the programming of the first transmitter erases all previous transmitter programming information, requiring the programming of all transmitters.

Program only 1 vehicle remote control door lock receiver at a time. If more than 1 receiver is being programmed at the same time, it is possible that the same transmitter could be programmed to more than 1 remote control door lock receiver.


Perform the following steps in order to program the transmitter:

Remove the ignition key from the ignition lock cylinder.
Remove the BCM PRGRM fuse from the fuse panel. Refer to Fuse Block in Wiring Systems.
Close all of the doors.
Close the liftgate.
Turn the ignition lock cylinder to ACC.
Turn the ignition lock cylinder to OFF, and then back to ACC within 1 second.
Open and close any vehicle door. A chime will be heard when the system enters the BCM programming/diagnostic mode.

Important
After 7 seconds, a chime may be heard confirming successful synchronization. It is necessary to wait approximately 14 seconds for a second chime that will confirm successful programming.


Press and hold the transmitter LOCK and UNLOCK buttons simultaneously for 14 seconds.
Repeat the previous step on each additional transmitter to be programmed.
Remove the ignition key from the ignition lock cylinder.
Install the BCM PRGRM fuse back into the fuse panel. Refer to Fuse Block in Wiring Systems. IF THIS WAS HELPFUL,PLEASE RATE,THANK YOU

Posted on Jul 15, 2010

  • 2 more comments 
  • readerproduc Jul 15, 2010

    It's for a DVD player...does the same thing apply?

  • Ronny Bennett Sr.
    Ronny Bennett Sr. Jul 15, 2010

    No ,if it is a factory dvd,that came in the van,go to the dealer,if it is a store bought,you will have to get in touch with the manufacture.

  • readerproduc Jul 15, 2010

    Thank you so much!

  • Ronny Bennett Sr.
    Ronny Bennett Sr. Jul 15, 2010

    Thank you,please rate,thank you.

×

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

    Sergeant:

    An expert that has over 500 points.

  • Master
  • 383 Answers

Try the pontiac dealership, screw the company

Posted on Jul 15, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Door lock will not unlock from switch on 2003 pontiac montana


How do you know the replacement switches were good? These actuators work in a series...One could be defective, causing the others (including drivers door) to not work...Also try cleaning all contact points with PB Blaster, and wipe dry...Hope this helps.

Apr 02, 2012 | 2003 Pontiac Montana

1 Answer

Gas gauge always reads full.


Hello John.
The Montana/Venture vans have a problem with the fuel gauge sending units in the early 2000's.
The only cure is to drop the fuel tank, remove the sending unit and replace it.
The fuel gauge sending unit is available separately from the fuel pump.
Thank you for using FixYa.
KL

Dec 19, 2010 | 2003 Pontiac Montana

1 Answer

My van pontiac montana 2003, and I took it to a shop, and said that It needs the all-motor mounts replaced. my question is: How do you replace the motor mounts specially the one on the transmission?


hello there I have a 2003 montana since it hit 200,000 k's its making this weird sound from the front end, like a humming when you speed up , or driving normal not sure what is going on , can you help me out ...

Jun 02, 2010 | 2003 Pontiac Montana

1 Answer

Where is the computor placed in my van pontiac montana 2003


Hello Burger.

The engine control module is mounted on the left front under the hood to the left of the air filter.
It is under a plastic cover.
Hope your repair goes well for you.

KL

Mar 02, 2010 | 2003 Pontiac Montana

1 Answer

My 2000 Pontiac Montana van needs the two front control arms replaced. I was quoted $637. Is this a fair estimate?


Thats a very fair estimate.

Tha job requires 1.8 hours per side and a front end alignment.

Aug 27, 2009 | 2005 Pontiac Montana SV6

1 Answer

Replace seats in 2003 Montana with seats from 2000 Montana


I would disconnect the battery minus - cable first, ensure the airbag connectors are the same ! otherwise I do not think you have a problem !!

Aug 11, 2009 | 2003 Pontiac Montana

1 Answer

Remote garage door


drive away from your house and find a place to park. Take your garage door opener and hold it up by the openers on you van . Press the button that you want to operate you garage door and the original opener at the same time it should flash 2 or three times . Now you should be able to use the one that came with the car. (note: it will depend on the age of you garage door opener)

Mar 22, 2009 | 2005 Pontiac Montana SV6

1 Answer

2005 Pontiac SV6 Montana key fob unlocks doors but will not lock


For the sliding doors you need to clean the contacts, there are 6 or 8 on both sides, just wipe them clean as they are probably covered in oil/grease/grime.

Feb 12, 2009 | 2006 Pontiac Montana SV6

2 Answers

2005 PONTIAC mONTANA-NO HEAT


your radiator may have frozen the thermostat

Jan 05, 2009 | 2005 Pontiac Montana

Not finding what you are looking for?
2005 Pontiac Montana Logo

306 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8202 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...