Question about 1988 Ford F 150

1 Answer

I CHANGED THE CLUTCH IN MY TRUCK AND NOW IT WONT BLEED WHY WOULD THAT HAPPEN

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Ford Master
  • 959 Answers

Try this...
fill the reservoir (clutch master cylinder) and open the slave until fluid runs out of the slave... tighten the slave bleeder and you should have pedal.

Posted on Jul 16, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Shifting gear problem


Hi Lillean,first go check your clutch master cylinder,it's located at firewall on driver side in corner,if low or empty,then your clutch slave cylinder is bad and leaking,it's located on side of transmission with hose connected to it,2 bolts hold it on,fluid may be visible if leaking.You can fill reservoir and bleed to get home,I have a 85 Nissan truck,happen to me before.To bleed,have some one pump pedal a few times,get line wrench and open valve at slave cylinder,do untill air is gone and pedal is firm,make sure you keep reservoir full while doing this or air will get in there.Here's a link on it.Join the az site like me then you have a free repair guide.

Dec 07, 2013 | 1991 Nissan Pickup

1 Answer

Chevy truck transmission


You have air in the hydraulic clutch system.

Nov 06, 2013 | Cars & Trucks

1 Answer

I need help changing out the master cylinder in my '94 toyota 4x4 pickup truck. It is a 5speed, i have already changed out the slave cylinder and installed the master cylinder but i still can not get the...


did you bleed the system?? you must bleed the system from the clutch slave. if this has been done, I need more info!! How does the clutch pedal feel, is the clutch slave engaging at all??

Sep 27, 2010 | 1994 Toyota Pickup

1 Answer

New clutch not working properly really could use some help


My best guess on this, assuming that the clutch master is working and it has no air remaining in the system is that you either have the wrong throwout bearing in there or that it is installed incorrectly. Also, rare but can happen is that if the pressure plate assembly is a rebuilt one, the face has been cut too far and clearances are off.
Obviously, check everything external before taking it apart again, but that's where I think you will need to go.

Nov 18, 2009 | 1991 Toyota Pickup

5 Answers

Stuck clutch pedal on a Mazda B series truck


Replace both clutch slave and master cylinders, and bleed well. I've also had this happen.

Jul 11, 2009 | 1988 Mazda B2200

1 Answer

Clutch wont let gears go in..


Was the clutch replaced?
Have you verified release travel?
open slave cylyder andv remove clutch fluid master cykider cover. permit gravity bleed untill fluid constantly drips, then close and refill. No pedal pump needed. let gravity bleed.

May 18, 2009 | 1999 Ford Ranger SuperCab

1 Answer

Dodge dakota 87


Hi, Just a thought, is the clutch drive plate in the right way round?
Press the Blue Button please if sorted!
Paul 'W' U.K.

Feb 08, 2009 | 1995 Dodge Dakota

1 Answer

I put a new clutch in it and every thang went good but went to ingag the clutch and it wont go in to gear in lees the truck is not streted when u put the truck in gear then step on the cluch it trys to go...


HI there... You might be right. If you can't put the truck into gear then you might have air in the slave. Try beeding it and see if that helps.

Jan 28, 2009 | 1995 Dodge Dakota

2 Answers

1999 Dodge Ram 3500 Pickup - Clutch


use a hand vacumn and cover over the reservoir, apply light vacumn and the air will come to the reservoir, usually take 2 or 3 time and the air will work back out to the top,

Jun 05, 2008 | 2001 Dodge Ram 3500 Truck

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

107 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5470 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...