Question about Mazda B-Series Truck

1 Answer

94 MAZDA TRUCK B SERIES, HAVE TO KEEP PUTTING BRAKE FLUID IN THE MASTER CYCINDER. HAS BEEN CHECKED THEY CANNOT FIND A LEAK NO WHERE. HELP?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Mazda Master
  • 22,095 Answers

Master cylinder as its being sucked into the brake servo ,from the rear seal

Posted on Jul 15, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 94 toyote camry 4 cylinder, I have to refill the brake fluid almost everyday but I have not noticed any leaks what is wrong?


have the system checked for leaks then check the rear of the master cylinder for leaking out of the master. if these leak you may not see it unless you move it away from the power booster to visually inspect. to keep adding fluid there is a leak you just have not found it.

Jan 08, 2015 | 1994 Toyota Camry

2 Answers

Why is Clutch pedal is going straight to the floor?


you have a leak on your clutch master you need to replace probably the leak started small and now its worst

Jun 09, 2014 | 1994 Mazda 323

1 Answer

1991 Mazda B2200 Series Brake light and Anti-lock light on? Brake pedal pushed to the floor and truck won't stop. Is it the master cylinder and wheel bearing?


The master cylinder and the wheel bearings are completely un realated parts. The first thing to check is the brake fluid level. If it's full and you have zero braking and zero pedal then you may well have a dead m/c. If you find an empty reservior, fill it and then figure out where it went. A leak anywhere will have the same result, no fluid, no brakes. The ABS issue may or may not be related but you need to solve the no pedal problem first.

Nov 05, 2013 | 1991 Mazda B-Series

1 Answer

How to bleed brakes on 94 firebird after putting brake fluid in


3 ways to bleed.
1) Gravity bleed. Start at the rear wheel brake farthest from the master cylinder. Open the bleeder screw about two full turns, and after a while, the brake fluid which is on top of the air will push the air out. When the brake fluid runs out, close the bleed screw. This can take 1/2 hour sometimes. You must keep checking that wheel so you can close the screw BEFORE you drain your master cylinder!
Continue this with all four wheels. P.S. Sometimes it will not work.Then you have to go to -
2) Bleed with a helper.
Helper gets in the car, and you ask them to push the brake pedal. You open the bleeder screw slowly and carefully, knowing the brake fluid may shoot out violently. Gently open it until bubbles come out. Close the screw, and ask the helper inside to pump up the pedal (about 5 times), and then hold it down medium hard. Continue to open the screw gently until only brake fluid comes out. Close that screw, and move to the next wheel. Repeat on each wheel. Check master cylinder ever few bleeds to keep it full.
or
3) take it somewhere and have it professionally bled with a machine.

Jan 06, 2013 | 1994 Pontiac Firebird

2 Answers

94 buick century brake pedal goes to floor and I have no brakes


ck the brake fluid level. if its out, then fill it up, pump the pedal and find the leak.

Sep 07, 2011 | Buick Century Cars & Trucks

1 Answer

I can start my 1998 mazda b2500 pickup truck but it will not shift into gear


The truck must be a standard trans? If you can shift it with the motor not running, but not with it running, then most likely the clutch master cyl must be low on brake fluid. It must have a leak. Sometimes you can add brake fluid, then pump the clutch pedal slowly and you might be ok. But you will need to get it repaired.

Dec 15, 2010 | Mazda B-Series Truck Cars & Trucks

3 Answers

1996 Suburban. Does the brake pedal gradually go all the way to the floor if the problem was worn brake pads ????


no worn pads do not cause a sinking pedal, you have a defective brake master cylinder, the seals inside the master cylinder are leaking

Sep 22, 2010 | 1996 Chevrolet Suburban

5 Answers

Stuck clutch pedal on a Mazda B series truck


Replace both clutch slave and master cylinders, and bleed well. I've also had this happen.

Jul 11, 2009 | 1988 Mazda B2200

3 Answers

Brake peddle goes to the floor intermitantly.


The problem may be that the master cylinder needs to be bench bled,there is most likely air trapped in the piston of the master cylinder.The problem comes from the piston not being fully actuated when connected to the pedal assembly.A vacuum bleeder will generally pull it out.

May 25, 2009 | 2004 Dodge Ram 2500

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

52 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7710 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...