Question about 1995 Chrysler Cirrus

1 Answer

Need to change out a/c pressure switch on a 95 chrysler cirrus .is it hard to do? 2.5 engine

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Guru:

    An expert who has written 7 tips or uploaded 3 video tips

  • Master
  • 630 Answers

It is not hard to do just be certain you have the proper socket wrench for removal and installation, proper way to do it is to have the system evacuated with a vacumn pump but if you want it done quick and cheap, be sure the engine is off as well as the a/c...just loosen the switch, wear protective clothes and googles so freon doesn't blind you or give you a spot of frost bite on your fingers when removing the switch. Make sure the new switch has thread sealant on the threads before installing to be certain the threads on the new switch wont allow any freon gas to leak out when the system is running.
IF YOU LOST A LOT OF FREON GET A FREON INSTALL FITTING KIT WITH AT LEAST TWO CANS OF FREON 134A AND INSTALL THROUGH THE LOW FILL PORT WHICH IS THE SMALLER FITTING THAT IS EMBEDDED INTO THE LARGER DIAMETER A/C LINE, (sorry for the caps) .............. make sure you have the a/c system on high blow full a/c and the engine idling while filling the system, if the freon wont gho in due to the a/c compressor clutch not engaging jump the new low pressure a/c switch connector out with a jumper wire accross the two wire terminals until you are done charging the system.
Hope this helps.
Happy Motoring!!

Posted on Jul 15, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the low pressure port for the air conditioning on my 95 cirrus lxi?


Just look around for it - it's obviously going to be on one of the A/C lines - possible under the engine cover. They can be tricky to locate but just keep an eye open - they usually have a black cap on them. There's 2 ports, high and low - the smaller one is the low side.

May 07, 2011 | Chrysler Cirrus Cars & Trucks

2 Answers

Where is the oil pressure sending unit located on a 1999 chrrsler cirrus


There are three engines that come with this car, there are two engines 2.0 and2.4 with the oil pressure switch located on the right front of the engine block, and then if it has the 2.5 engine then the oil pressure switch is located on the leftside of the engine block above the oil filter, good luck,.

Jan 01, 2011 | 1999 Chrysler 300M

3 Answers

My cirrus dies after driving about 5 miles and then dies. If I wait 5-15 minutes I can restart it and go a short distance 1- 2 miles and then repeats Thanks Jim repair center replaced crank sensor and no...


change the fuel filter.The engine is running out of fuel & possibly the fuel line is experiencing vapor lock due to insufficent gas.Hope this helps you & good luck!

Aug 19, 2010 | 2000 Chrysler Cirrus

1 Answer

How to replace fuel pump on 95 chrysler cirrus.Need detailed instructions on how to remove and replace fuel pump module on 1995 Chrysler cirrus.


to detailed to explain here. buy a hanynes repair manual at local auto store, 17$ it'll explain step by step.

Jul 01, 2009 | 1995 Chrysler Cirrus

1 Answer

Check engine light


Code 12.................Problem with the battery connection. Direct battery input to PCM disconnected within the last 50 ignition key-on cycles.

either a loose connection or the battery dead or removed within 50 last times you turned on the car, check battery terminals for corrosion or loose connector, and check the earth wire for corrosion, the code will dissapear by itself if the power is not removed again

Apr 11, 2009 | 1995 Chrysler Cirrus

1 Answer

Check engine light comes on


Code 12 means That the Crankshaft position sensor may need replacement.It is located near the crankshaft maybe under the timing cover.

Apr 07, 2009 | 1995 Chrysler Cirrus

1 Answer

96 chrysler cirrus 2.4 pouring out oil


going to be hard to see but the sensor for oil pressure is located in the rear somewhere close to the oil filter area. find that sensor bad alot. try that

Apr 06, 2009 | 1996 Chrysler Cirrus

1 Answer

Coolig system


The drain is a plastic fitting at the bottom of the radiator, sometimes it is hard to see, you will need to jack the car up in most cases and crawl under it to located the drain ****.

Oct 19, 2008 | 1995 Chrysler Cirrus

2 Answers

Coolant sensor


refill and bleed the cooling system.  The water from your overflowing radiator may be the cause of you engine problems....dry of the motor.

Oct 16, 2008 | 1996 Chrysler Cirrus

Not finding what you are looking for?
1995 Chrysler Cirrus Logo

288 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...