Question about 1999 Ford Taurus

1 Answer

REPLACING THE OIL PUMP

DO I NEED TO REMOVE THE ENGINE TO PUT IN A NEW OIL PUMP FOR A 1999 FORD TAURUS

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that gotĀ 5 achievements.

    Vice President:

    An expert whose answer gotĀ voted for 100 times.

    Champion:

    An expert who has answered 200 questions.

  • Contributor
  • 245 Answers

No you can jack the motor high enough to get a 2x4 between the engine mount and frame and drop the pan,,,,,,,,,,,,,,,,, take the 2 right side engine mount bolts off from the frame ,,, raise the engine high enough to get the 2x4 between the frame and engine mounts...then drop the pan out of it

Posted on Jul 15, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Where Is The Oil Pump Located>? And How Do I Replace The Oil Pump


Here you go. BIG Job!

http://www.ehow.com/how_4506339_replace-oil-pump-ford-taurus.html

The oil pump is an essential piece of equipment that keeps your Ford Taurus running. It lubricates the engine by keeping the oil circulating. Without this lubrication, the engine wouldn't run. An oil pump is usually located in the oil pan. If you want to change the oil pump and replace it with a new one, roll up your sleeves and get ready for some dirty work.

How to Check if an Oil Pump Is Bad

Things You'll Need




  • Wrench



  • New oil pump



  • New A/C bolts

Remove Old Oil Pump


  1. Drive your Ford Taurus up onto ramps or lifts so you have room to work as you pull out the oil pump. You could also use a jack, but make sure you brace the front wheels so they don't roll. In addition, set the emergency break firmly into position so the car doesn't roll.


  2. Take the engine out and put it on an engine stand then remove the upper intake manifold. Take off the valve covers then the accessory drive belt.


  3. Remove the power steering pump and the alternator. The water pump is the next component to remove, followed by the A/C compressor and bracket.


  4. Rotate the pulley shaft clockwise to remove the crankshaft pulley. It has left-handed threads.

  5. Pull out the oil pan and the oil pump screen and tube. Take off the front cover and the timing chains and remove the crankshaft timing gears. Finally, remove the oil pump, taking note of the bolts you removed and in which order you remove them.

Insert New Oil Pump


  1. Install the new oil pump and put the bolts back on in the same manner you removed them. Tighten these bolts to 71 to 106 in-lb.


  2. Reinsert the crankshaft timing gears, timing chains and front cover. Put the oil pump screen and tube back on, torquing the bolts to 71 to 106 in-lb, and torque the nut to 15 to 22 ft-lb.

  3. Put the oil pan back in, then the crankshaft pulley. Install the A/C compressor and bracket using new bolts for the A/C. Add the water pump, alternator, power steering pump, the accessory drive belt, valve covers and upper intake manifold.


  4. Replace the engine back into your Ford Taurus and fill the crankcase. Start your engine and look for leaks in the area you were working.

Read more : http://www.ehow.com/how_4506339_replace-oil-pump-ford-taurus.html

Aug 06, 2015 | 2004 Ford Taurus

1 Answer

How to remove the water pump drive belt on a 1999 ford taurus dohc 6cyl


here is a video for the sohc motor is it about the same way

Jan 27, 2013 | 1999 Ford Taurus

1 Answer

My 1999 Ford Taurus has the check engine light and oil light on. The lifters are rattling. I removed the oil pump and put a drill on the shaft and it pumps oil. Do you know what else it could be?


Just because the oil pump is turning doesn't mean it pumping enough oil. I think the first thing you should do is get a mechanical oil pressure guage hooked into the system and read the oil pressure you actually have. This will determine what to do next.

If you have a high mileage engine then perhaps a thicker oil may fix the noisy lifters. Go to 10W40 or maybe even 20W50. This should stop the lifters from rattling and boost your oil pressure if it's low. A compression test would help to confirm the wear from high mileage.

It could also be that the oil passages are partially clogged and while you have enough oil pressure, it's not getting where it needs to be in sufficient volume. If this is the case, I would try using an oil additive to help clean it up. Just be sure to increase the frequency of your oil changes to keep the crud out of the oil system.

It's also possible that your engine has enough wear and tear from mileage that it will need to be overhauled or replaced. Generally a good used engine is cheaper than a rebuild. Be sure to check out the warranty from the scrap yard first. Hope this helps.

Nov 15, 2011 | 1999 Ford Taurus

2 Answers

I hav 2001 ford taurus 3.0 single head cam engine makes noise , mechanic said that oil pressure is low n need change oil pump. but oil light not comes on always, it becames on only driving, when I...


That sounds like a pump... the oil pump is inside of the engine. You need to drop the oil pan to gain access - however, you will need to pull the motor to do that.

Jan 25, 2011 | 2001 Ford Taurus

1 Answer

My radiator continues to boil over, I have to continuously put water in radiator. I have put new water pump on, themostat been changed. Continues to lose water,


have you checked your engine oil for any signs of water in it? It looks like a head gasket problem if there are any signs in oil, otherwise the system has an airlock and needs to be bled properly.

Aug 31, 2010 | 1999 Ford Taurus

1 Answer

Do i need to replace the oil pump strainer when i replace the oil pump for 1999 ford taurus or repale any other gaskets besides the oil pan gasket


The strainer would need to be completely clean and undamaged or bent, Then okay. Ususally the pan does not come right out, and you have to release motor mounts, and raise the engine.

Jul 15, 2010 | 1999 Ford Taurus

1 Answer

Where is the oil pump located on a 1999 ford taurus and whats items do i need replace a long with the oil pump


Remove oil pan oil pump and pick up tube & screen will be bolted on.
You should get oil pump lube, carb. cleaner, new pump oil,
oil pan gasket, silicon, oil & filter, loc-tight, gasket remover & tools metric, 1/4 drive socket set, scraper / putty knife, 2 jack stands, a jack or ramps,
& blocks for rear wheels.
Lets get started.

(1)Get your car up on stands or ramps block rear tires.

(2)Drain oil & remove oil filter remove battery cable NEG (-)

(3)remove pan

(4)remove old pump

(5)remove pick up tube from oil pump

(6)Now clean tube & screen with carb. cleaner place on news paper to dry.

(7) clean all old gasket off from engine & pan also clean bolts

(8)place silicon on pan place gasket on pan put bolts in from gasket side to Aline holes put a side to dry

(9) Attach tube to pump with a little loc-tight fill pump with oil pump lube

(10)attach pump to engine block make sure rod goes in proper & bolt are tight.

(11)Bolt pan back on engine using a 1/4 in drive ratchet don't over tighten bolts get all bolts in now slow run each bolt in starting at 1 end then jump to the other then go to bolt at other end a cross from 1st bolt. Do this till all bolts are ran in. Now tighten bolts look for gasket on side of pan.If it starts to push out stop go to next bolt.

(12)Instill new filter & drain plug,& pour in oil

(13)Replace Neg - cable

I hope this works for you it's a basic oil pump change for most cars.
Some take more steps.

Jul 14, 2010 | 1999 Ford Taurus

1 Answer

Need to remove external oil pump on a 95 ford tauras 3.8 v6.what all is involved doing this??


Oil Pump

Removal


  1. If necessary, remove oil bypass filter (oil filter).
  2. Remove oil pump and filter body to engine front cover retaining bolts and remove oil pump and filter body from engine front cover.
  3. Inspect oil pump body seal (6C639), oil pump and filter body and engine front cover for distortion and wear. Replace components as necessary.
Installation

  1. Position oil pump and filter body on engine front cover and install retaining bolts.
  2. Tighten the small engine front cover retaining bolts to 8-11 Nm (71-97 lb-in) . Tighten the large retaining bolts to 23-32 Nm (17-23 lb-in) .
  3. If removed, reinstall oil bypass filter (oil filter).

Dec 04, 2009 | 1995 Ford Taurus

1 Answer

1999 ford taurus isn't getting fuel


Oil pressure sensor is part of the fuel circuit. You changed engines, did the new one have the same sensor?

Aug 30, 2009 | 1999 Ford Taurus

1 Answer

Oil Pump Replacement


Yes the oil pump is inside the engine oil pan, you will have to remove the exhaust to get the pan off.

Jul 31, 2008 | 1999 Ford Taurus

Not finding what you are looking for?
1999 Ford Taurus Logo

168 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...