Question about 1989 Chevrolet S-10 Blazer

2 Answers

Where is the ignition switch in an 1989 chevy S-10

Posted by on

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 3,092 Answers

Remove lower dash panel, under steering wheel, there will be a bracket that holds steering wheel, remove both 15mm nut's that point up, not the 13mm bolt's the screw into the colum , steering wheel will come down enough where you will see the ignition switch on the top side of the colum, the switch will be screw to the colum with the head light dimer switch.

Posted on Jul 15, 2010

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Chevrolet Master
  • 75,822 Answers

It is mounted on the tube of the steering column near the bottom on top of tube, it is driven by a rod from the ignition lock cylinder.

Posted on Jul 15, 2010

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 275 Answers

SOURCE: 1989 Chevy Pick up Ignition switch broken

use a test light the wire from the battery should be hot all the time the wire that goes to the solenoid should be hot when the key is turned over to start and the wire going to the coil should be hot when the key is in run.

Posted on Nov 12, 2008

emissionwiz
  • 75822 Answers

SOURCE: how to replace an ignition switch on a 1989 chevy

go to link the year is diff but the procedure is the same. scroll to bottom of page

http://www.2carpros.com/forum/1994-chevy-s-10--ignition-lock-cylinder-vt197051.html

Posted on Sep 09, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replace Ignition Switch Support 89 chevy


I am unaware of what you are refering to with "ignition switch support".
The ignition switch is attached to the steering column near the bottom (close to the firewall). Its held on by two screws (the dimmer switch is also attached to a screw and the ignition switch). The bracket on the ignition switch is part of the switch.

Oct 08, 2011 | 1989 Chevrolet C/K 2500

1 Answer

1989 Suburban runs but sometimes will not turn over until it sits


You may have a bad connection going to ignition switch or too the fuse relay box in engine compartment, check the power cable going to reay box in engine compartment.also you may have a bad ignition switch, not the cylinder lock but the eletrical switch itself.

Jun 26, 2010 | 1989 Chevrolet Suburban

1 Answer

Wiring problem from the fuel pump relay on the firewall of my 1989 3/4 ton 4x4 gmc pickup - to the ignition switch - could it be an open circuit or the ignition switch itself?


The ignition switch could be the culprit. It's located on the lower half of the column, on top of it. Remove the plug, the two screws that hold it on, and lift it off the actuator rod that runs up to the key cylinder. It's about $30.00 new and takes about 10 minutes.

Or you could bypass the problem.

Feb 27, 2010 | 1989 GMC Sierra

1 Answer

No power to wiper motor, 1990 chevy s-10 blazer. No power to fuse block (just the wiper fuse)


It would have to be in the ignition switch,this ,when turned on,sends power to the fuse.

Feb 25, 2010 | 1989 Chevrolet S-10 Blazer

1 Answer

I have a 89 chevy blaser with an electral problem


how to replace a tailgate switch for a 1989 chevy silverado blazer

Oct 27, 2009 | 1989 Chevrolet S-10 Blazer

1 Answer

1989 Chevy Silverado C 1500 Truck


The ignition switch is mounted on the top of the steering collumn, and is connected to the switcth with a rod. Top of column down by the pedals.. Remove and test switch.

Jun 03, 2009 | 1989 Chevrolet C1500

1 Answer

Club car golf cart won't start.


i have a 1989 club car 10 amp fuse is under seat in a box under air box should have one screw in center of lid

Mar 29, 2009 | 2002 Chevrolet Avalanche

1 Answer

1989 Chevy Camaro Security system


Just take every cord connected to the positive side of the battery off for 10 seconds to allow the alarm to reset, then flip the little switch under the dash so the alarm won't activate again.

Jan 02, 2009 | 1989 Chevrolet Camaro

1 Answer

1989 Chevy Pick up Ignition switch broken


use a test light the wire from the battery should be hot all the time the wire that goes to the solenoid should be hot when the key is turned over to start and the wire going to the coil should be hot when the key is in run.

Nov 08, 2008 | 1989 Chevrolet K1500

Not finding what you are looking for?
Cars & Trucks Logo

317 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8210 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...