Question about 1998 Dodge Ram 1500 4WD

1 Answer

How to get to top screws on dashboard to remove dash without taking out windsheild

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Master
  • 4,793 Answers

You need to modify a screwdriver(buy the tool).
L shape or use an allen key ground to a semi point.

Posted on Jul 15, 2010


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Where is the blower resister on the 2011 sorento? I found the blower behind the glove box but don't know which one is the resister?

If you are referring to the "heater" blower motor resister?
It is under the top section of the dashboard where the shelf detent pad is. First remove the screws on top of the pad area, next start lifting up the right side of the dashboard section towards the center and over towards the left over the instrument cluster and lift out the complete top of the dash. Next remove the defroster duct by removing the screws. Unclip from the lower section and the duct will lift out. The resister is located there under the dash area and will unbolt allowing removal. "Good Luck."

Apr 11, 2017 | Cars & Trucks

3 Answers

Padded Dashboard

I think your manual can help you in this matter .

I am not car expert but whenever i have problem in my car i used to go by manual for assembly and disassembly purpose .

If i have problem then i will go with experts .

Sep 18, 2008 | 2000 Daewoo Leganza

3 Answers

How do you remove the glove box on a 2002 Sebring to take off dashboard?

Can you be more specicic please... a removed my dashboard many times... you must remove decor. strips around, there are no screws, just patents and uder them are screws, which holds plastic cover and when the cocer is taken down, you find screws, which holds dashboard...

PS: Sorry for English I am not from eng. speak country...

Mar 21, 2015 | 2002 Chrysler Sebring

1 Answer

Need a digram of taking a dashboard out of a 2005 impala

  • Turn the engine of the Impala off and open its hood. Use a socket wrench to remove the negative cable from the battery.
  • Remove the four screws securing the driver's side kick panel, using a Phillips screwdriver. Use a slotted screwdriver to pry out the kick panel. Remove the passenger's side kick panel the same way.

  • Remove the metal plate from the driver's side of the vehicle under the Steering wheel by detaching its two securing bolts with a socket wrench. Pull the plate off to reveal three electrical connections. Unplug the three connections.
Glove Compartment
  • 4 Open the glove compartment and empty its contents.
  • 5 Remove the two screws at the back of the glove compartment.
  • 6 Pull the glove compartment off of the dashboard.
Center Dash Panel
  • 7 Remove the two screws securing the radio and the two screws securing the A/C unit with a Phillips screwdriver.
  • 8 Remove the four corner screws of the center dash panel faceplate with a Phillips screwdriver. Pull the faceplate off.
  • 9 Use a slotted screwdriver to pull the radio and A/C unit toward you.
  • 10 Reach behind the two devices and disconnect their connections. Pull them out of the vehicle.
  • 11 Remove the two screws underneath the steering wheel, using a Phillips screwdriver.
  • 12 Remove the two screws on the lower right side of the dashboard, using a Phillips screwdriver.
  • 13 Remove the 10 mm bolt from both side panels with a socket wrench.
  • 14 Remove the defroster grille by pulling it out. Remove the four screws along the top of the dash near the windshield.
  • 15 Pull the dashboard off the Impala and detach the two electrical connections. Lift up the dashboard and remove it from the vehicle.

Sep 22, 2012 | 2000 Buick LeSabre

1 Answer

How do i take apart dash of 2001 Sante Fe to replace radio

1. Remove the NEGATIVE battery cable (to avoid accidently causing vehicle damage due to shorting out electrical circuits)

2. Remove the ash tray

3. Remove the screws securing the center facia panel

4. Remove the center facia panel by gently prying rearward to release clips

5. Remove screws securing audio unit

6. Remove audio unit from the mounting bracket.

7. Installation is the reverse of removal.

Jun 02, 2012 | 2001 Hyundai Santa Fe

1 Answer

How do you take of the dash paneling to install a new aftermarket cd player?

  • Disconnect the negative battery cable from the Jeep Cherokee battery with the 10 mm wrench.
  • 2 Remove the five screws on the top edge of the dash panel with a Phillips-head screwdriver.
  • 3 Pry the trim panels surrounding the climate control knobs away from the dashboard with the trim panel removal tool.
  • 4 Remove the trim panel that surrounds the headlamp switches (located to the left of the steering column) with a trim panel removal tool.
  • 5 Remove the two screws behind the trim panel that surrounds the headlamp controls with a Phillips-head screwdriver.
  • 6 Pull the dash panel that surrounds the stereo and covers the instrument panel of the Cherokee, away from the dashboard by hand.
  • 7 Remove the two screws from the stereo mounting bracket. One screw is on the bottom left corner, the other screw is on the top right corner. Each screw can be removed with the 10 mm socket and drive.
  • 8 Pull the factory stereo from the stereo mounting dock.
  • 9 Disconnect the stereo wiring from the back of the factory unit.
  • 10 Connect the Jeep Cherokee factory stereo wiring to a wiring harness adapter. Connect the wiring harness adapter leads to an aftermarket stereo. Slide the aftermarket stereo into the stereo mounting bracket and replaced two screws at the opposite corners with the 10 mm socket and drive.
  • 11 Replace dash panel that stretches across the top of the steering column.
  • 12 Replace the two screws at the top of the headlamp control switch. Replace the trim panel around the headlamp switch.
  • 13 Replace the trim panel that surrounds the climate control knobs.
  • 14 Replace the five screws on the top edge of the dashboard with a Phillips-head screwdriver.
  • 15 Replace the negative battery cable over the negative battery terminal and tighten the cable to the negative lead post with the 10 mm wrench

  • Dec 24, 2010 | 2006 Jeep Grand Cherokee

    1 Answer

    How do I remove dashboard to get to instrument panel to replace bulbs?

    You will need a cross point screw driver

  • 1 Remove the two screws on the underside of the top of the trim panel surrounding the dash and instrument panel.
  • 2 Pull the trim piece off the dash.
  • 3 Remove the four screws that hold the instrument panel in the dashboard using a cross point screwdriver.
  • 4 Slide the dashboard instrument panel forward and disconnect the electrical connector from the back of the dashboard.
  • 5 Turn the instrument panel over.
  • 6 Turn the base of the dashboard light bulb counterclockwise to unlock it from the instrument panel and pull it out of the panel to remove it.
  • 7 Insert a new light bulb into the back of the panel, and turn the bulb clockwise to lock it into the panel.
  • 8 Plug the electrical connector back into the instrument panel and slide the panel back into the dashboard.
  • 9 Secure the panel with the factory mounting screws and replace the trim and trim-mounting screws using a screwdriver.
  • Nov 23, 2010 | 1999 Toyota Sienna

    1 Answer

    How do you remove the dash on a 2002 impala so I cn get to the radio?


    Thanks for contacting

    Open both front doors, remove the fuse panel/relay cover panel at top by pulling straight off. There is a screw at the top which holds part of the dash panel, remove screw, do the same on the other side. Remove two screws at the center of drivers side of dash at top which screws in to the top of the dashboard. Remove small lower dash panel around steering column, it has two screws.You will have to unplug four electrical connectors, Two are on lower panel for floor light and trunk release. Two are on main dash panel, one for Traction control and one for hazard light. Start to pry from drivers side, the dash panel, it has snap clips and work across to pass. side. sash panel will lift off. This will leave acsess to radio.

    Let us know if you have something more to know else please accept the suggestion.
    Thank You.

    Jun 01, 2010 | 2002 Chevrolet Impala

    1 Answer

    Cracked fascia of dashboard

    Clarification of the would be greatly appreciated. However the entire dash is held on with about 10-15 screws.
    Open both doors and pop off the platic covers normally hiden when the doors are closed. Remove the screws from both sides here.
    Then open the glove box. There are 2 screws that hold on a metal bracket, remove them.
    On the top-middle of the dash there is a vent to defrost your windshield.One screw holds it on, remove it (phillips I believe).Then remove the screws under the vent so that the dash can be completly removed.
    The top part of the dash a 5" strip closest the to windshield will have to be removed frist. By simply pulling it up from the sides.
    The entire dash can then be removed fairly easy by pulling it apart from the housing for the odometer and across the entire dash.
    The housing that is around your odometer can then be removed by simply removing a few screws across the top and under the radio. You will have to disconnect the wireing harness for the light adjuster left of the blinker on the dash. to remove this part. (I had a little trouble getting this out so I had to take apart the plastic housing for the ignition. 3 bolts slightly bigger then the ones on the dash under neath.)

    Jan 10, 2010 | 2005 Chevrolet Cavalier

    1 Answer


    Remove the moulding around the dashboard display, remove the screws that hold the display in. The display will pull straight out then you need to reach behind and disconnect the multi plugs. Tilt the display to clear the steering wheel and dash board top. You can replace the circuit board on the back by simply removing the small screws that hold it together.

    Apr 06, 2009 | 2004 BMW 5 Series

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    41 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Dodge Experts


    Level 3 Expert

    83772 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22413 Answers

    Ronny Bennett Sr.
    Ronny Bennett Sr.

    Level 3 Expert

    6927 Answers

    Are you a Dodge Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides