Question about 2000 Chevrolet Tracker

1 Answer

Belt routing diagram 20000 chvy tracker - 2000 Chevrolet Tracker

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.


    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 66 Answers

Hi You can go to and sign up for my zone (my zone is free).thay have repair guides with belt routings.hope this helps.Thank You for using fixya iluv2fish......Ray......

Posted on Jul 15, 2010


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How to change the power steering/ac belt

It should have a 1/2 inch hole on the tensioner to put in a 1/2 inch breaker bar. Relieve the tension and remove the belt. Be careful, its heavy spring loaded. Make sure you know your belt routing for installing the new one. There should be a sticker with a belt routing diagram by the top of the radiator. This is for a serpentine belt. If for some reason you have a V-belt, you have to loosen brackets.

Feb 26, 2016 | 2001 Chevrolet Tracker

2 Answers

Need belt routing diagram gmc 2500 6.6 duramax

I need a belt routing diagram for an o 06 Duramax with air ps etc

Jun 29, 2011 | 2006 GMC Sierra 2500HD 2WD

1 Answer

How to replace timing belt on a 2003 chevy tracker

Open the hood and locate the accessory belt routing diagram that is stamped to the top flat surface of the radiator shroud. Use the routing diagram to properly route the new belt around each accessory pulley.
Look on the front of the engine between the alternator and the power steering pump and locate the automatic belt tensioner. Use the pulley that is attached to the end of the tensioner to loosen the tension from the belt.
Position a breaker bar and a 14 mm socket onto the bolt head in the middle of the tensioner pulley. Turn the breaker bar clockwise to loosen the tension from the belt. Slide the belt off of the tensioner pulley and slowly release the breaker bar.
Slide the belt out from around all of the engine accessory pulleys. Pull the belt around each of the fan blades and up out of the engine compartment.
Slide the new belt around each of the fan blades and around each of the accessory pulleys as directed by the belt routing diagram.
Turn the tensioner clockwise with the breaker bar and the 14 mm socket again. Slide the belt around the tensioner pulley and slowly release the breaker bar. Pull the breaker bar and socket off of the tensioner and out of the engine compartment.
Crank the engine for ten to fifteen seconds to finish seating the ribs on the inside of the belt to the grooves of each accessory pulley. Turn the engine off.

Feb 20, 2011 | 2003 Chevrolet Tracker

1 Answer

I need an Idler pulley or the pulley that runs air conditioner belt as well as the belt for the power steering

If your idler pulley is bad then unbolt it and while you're at it replace the power steering belt.

REMOVAL & INSTALLATION Because serpentine belts use a spring loaded tensioner for adjustment, belt replacement tends to be somewhat easier than it used to be on engines where accessories were pivoted and bolted in place for tension adjustment. Basically, all belt replacement involves is to pivot the tensioner to loosen the belt, then slide the belt off of the pulleys. The two most important points are to pay CLOSE attention to the proper belt routing (since serpentine belts tend to be "snaked'' all different ways through the pulleys) and to make sure the V-ribs are properly seated in all the pulleys. Although belt routing diagrams have been included in this section, the first places you should check for proper belt routing are the labels in your engine compartment. These should include a belt routing diagram which may reflect changes made during a production run.
  1. Disconnect the negative battery cable for safety. This will help assure that no one mistakenly cranks the engine over with your hands between the pulleys, and that the cooling fan cannot activate while servicing the belt(s). NOTE: Take a good look at the installed belt and make a note of the routing. Before removing the belt, make sure the routing matches that of the belt routing label or one of the diagrams in this book. If for some reason a diagram does not match (you may not have the original engine or it may have been modified), carefully note the changes on a piece of paper.
  2. For tensioners equipped with a 1⁄2 in. (13mm) square hole, insert the drive end of a large breaker bar into the hole. Use the breaker bar to pivot the tensioner away from the drive belt. For tensioners not equipped with this hole, use the proper-sized socket and breaker bar (or a large handled wrench) on the tensioner idler pulley center bolt to pivot the tensioner away from the belt. This will loosen the belt sufficiently that it can be pulled off of one or more of the pulleys. It is usually easiest to carefully pull the belt out from underneath the tensioner pulley itself.
  3. Once the belt is off one of the pulleys, gently pivot the tensioner back into position. DO NOT allow the tensioner to snap back, as this could damage the tensioner's internal parts.
  4. Now finish removing the belt from the other pulleys and remove it from the engine. To install:
  5. While referring to the proper routing diagram (which you identified earlier), begin to route the belt over the pulleys, leaving whichever pulley you first released it from for last.
  6. Once the belt is mostly in place, carefully pivot the tensioner and position the belt over the final pulley. As you begin to allow the tensioner back into contact with the belt, run your hand around the pulleys and make sure the belt is properly seated in the ribs. If not, release the tension and seat the belt.
  7. Once the belt is installed, take another look at all the pulleys to double check your installation.
  8. Connect the negative battery cable, then start and run the engine to check belt operation.
  9. Once the engine has reached normal operating temperature, turn the ignition OFF and check that the belt tensioner arrow is within the proper adjustment range. Fig. 1: Often the underhood label will display the serpentine drive belt routing 88231p43.gif
    Fig. 2: Relieve the belt tension by pivoting the automatic tensioner away from the belt, then remove the belt 88231p44.gif
    Fig. 3: Verifying serpentine belt alignment in the pulley 79244g60.gif
    Fig. 4: Fig. 1 Accessory V-belt routing — Tracker 1.6L engine with A/C 93024g03.gif
    Fig. 5: Fig. 2 Accessory V-belt routing — Tracker 1.6L engine with A/C and P/S 93024g04.gif
    Fig. 6: Fig. 3 Accessory V-belt routing — Tracker 1.6L engine with P/S 93024g05.gif
prev.gif next.gif

Jun 26, 2010 | 2000 Chevrolet Tracker

2 Answers

Looking for timing belt diagram on 97 Geo Tracker

Click on the following free, direct Link. It has the Timing Belt Diagrams, including Marks and Instructional Diagrams.

Let me know if this helped...

Apr 08, 2010 | 1997 Geo Tracker 2 Door

1 Answer

I need a serpentine belt/routing diagram 2000 chevy tracker.

For the 2000 Chevrolet Tracker:

Most modern vehicles have the Belt Routing Diagrams on the undeside of the Hood. But the sometimes disappear.

I do not know if you have the 1.6L In-Line 4-Cylinder, or the 2.0L DOHC In-Line 4-Cylinder. Nor what Engine Options you have (AC/No AC, etc.).

Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at!

Mar 27, 2010 | 2000 Chevrolet Tracker

1 Answer

How do i change the serpentine belt on my 1999 chevy tracker

First, keep this diagram around as you will need it to route the serpentine belt when you reinstall it. There may also be a diagram under the hood by the radiator.
7e98dff.jpg Next, follow this link and watch the video that shows you how to replace a serpentine belt...

Nov 14, 2009 | 1999 Chevrolet Tracker

Not finding what you are looking for?
2000 Chevrolet Tracker Logo

Related Topics:

173 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts


Level 3 Expert

79186 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides