Question about 1999 Chevrolet Monte Carlo

1 Answer

Need to know the torque specs for a rear wheel bearing on a 1999 monte carlo?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 6,826 Answers

Hub & Bearing 3.8L engine Removal & Installation To Remove:
Hub and bearing assembly mounting need to know the torque specs for a rear wheel - 88008g39.gif

All W-body cars are equipped with sealed hub and bearing assemblies. The hub and bearing assemblies are not serviceable. If the assembly is damaged, the complete unit must be replaced.

  1. Disconnect the negative battery cable.
  2. Raise and safely support the vehicle with jackstands.
  3. Remove the rear wheel and tire assembly.
  4. If equipped with rear disc brakes, remove the caliper, bracket and rotor.
  5. If equipped with rear drum brakes, remove the brake hose bracket and drum.
  6. If equipped, detach the ABS electrical harness.
  7. Unfasten the four hub/bearing-to-knuckle attaching bolts, then remove the hub/bearing assembly.
To Install:
  1. Install the hub/bearing assembly onto the knuckle. Install the four attaching bolts and tighten to 52 ft. lbs. (70 Nm).
  2. If equipped attach the ABS electrical harness.
  3. Install the rotor, caliper and bracket or drum and bracket, as applicable.
  4. Install the wheel and tire assembly.
  5. Carefully lower the vehicle.
  6. Connect the negative battery cable.

Posted on Jul 15, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need the Flywheel torque specs for a chevy 350


60 ft/pds. Check this out ,,,, http://www.chevellebigblock.com/intaketorquepattern.html

Sep 10, 2014 | 1999 Chevrolet Monte Carlo

1 Answer

Replace front hub bearings on 2002 chevy monte carlo


road wheel off, brake caliper removed from rotor disc, remove cap in middle of rotor exposing the bearing retaining nut, remove split pin that holds the nut from turning and wind off the large nut, once nut is removed you can remove the rotor and bearings, the rear roller bearing at the rear of the rotor may need to be levered off with a screwdriver, should come off easy, replace in reverse order

Jun 11, 2010 | 2002 Chevrolet Monte Carlo

1 Answer

What are the torque spec's for the exhaust


to torque nuts and bolts start in the center using a criss cross pattern working outward.. final torque is 12 ftlbs.

May 02, 2010 | 1996 Chevrolet Monte Carlo

1 Answer

2003 Chevy monte carlo 3.4L, need the torque


Check Autozone.com. There repair section should have the torque specs and order of tightening.

Mar 06, 2010 | 2003 Chevrolet Monte Carlo

1 Answer

Does the entire rear brake assembly need to be taken apart to install a wheel berring


you have to pull the rotor off and the bearings are on the spindle behind the rotor or the drum if they are drum brakes

Sep 25, 2009 | 1999 Chevrolet Monte Carlo

1 Answer

2000 monte carlo / noise from rear wheels


That's what it sounds like to me also. I would put the rear up on jack stands and spin the wheels to male shure wich side it is. Don't forget to block the front wheels for safety as you will not be able to set your e- brake for this test.

Aug 27, 2009 | 2000 Chevrolet Monte Carlo

1 Answer

2001 monte carlo ss. Rear wheel bearings making a grinding noise


It is pretty easy, there is not much labor involved if it has anti-lock brakes in the rear you will also have to un-plug the wire harness attached to hubs.

Nov 24, 2008 | 2001 Chevrolet Monte Carlo

1 Answer

1999 Chev. Monte Carlo steering wheel make's a scratchy slidding,


Either part you mentioned can cause this type of noise.

Apr 19, 2017 | 1999 Chevrolet Monte Carlo

Not finding what you are looking for?
1999 Chevrolet Monte Carlo Logo

391 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

77202 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...