Question about 2005 Chrysler Town & Country

1 Answer

Egr valve location on the motor for replacement

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 176 Answers

Unplug the connector and vacuum line. Then take out the two bolts. Clean the old gasket off and slap in the new one. In an hour you'll be done and down the road.



egr valve location - 78377811.gif
Additional Information provided courtesy of ALLDATA

Posted on Jul 15, 2010

  • stubby01 Sep 03, 2010

    Where is the EGR valve located on the engine?

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

What is a EGR valve & IAC valve & where are they located?


Here's a picture of your egr valve,located by firewall.Here's your iac.

Jan 17, 2013 | 2000 Chrysler Concorde

1 Answer

Erg flow insufficient


  • The DPFE (differential pressure feedback EGR) sensor is faulty and needs to be replaced
  • There is a blockage in the EGR (tube), most likely carbon buildup
  • The EGR valve is faulty
  • The EGR valve may not be opening due to a lack of vaccuum
It is quite common for people to just replace the EGR valve only to have the OBD code return. The EGR valve is not always the culprit.
  • Use a vacuum pump and pull the EGR valve open while monitoring engine RPM's & DPFE voltage. There should be a noticable difference in RPM's with the EGR open
  • Clean out the EGR valve and/or tubing to remove deposits
  • Check the voltage at the DPFE, compare to specified values (refer to a repair manual for your specific model)
  • Replace the DPFE sensor (with a good quality / OEM one)
  • Replace the EGR valve
The EGR valve is located in the engine compartment. Its should look this

2_7_2012_10_25_48_pm.jpg

Feb 07, 2012 | 2000 Mercury Sable

2 Answers

Engin light #po406 2005 ram quad cab


P0406 - Exhaust Gas Recirculation Sensor A Circuit High

Early Models : The EGR valve control the amount of exhaust gas routed to the intake manifold. Vacuum is applied to the EGR valve in response to the throttle opening. The vacuum control the movement of the taper valve connected to the vacuum diaphragm in the EGR valve.

zjlimited_230.gif

Late Models : The EGR volume control valve uses a step motor to control the flow rate of EGR from exhaust manifold. This motor has four winding phases. It operates according to the output pulse signal of the ECM. Two windings are turned ON and OFF in sequence. Each time an ON pulse is issued, the valve opens or closes, changing the flow rate. When no change in the flow rate is needed, the ECM does not issue the pulse signal. A certain voltage signal is issued so that the valve remains at that particular opening.

zjlimited_231.gif

Symptoms
- Engine Light ON (or Service Engine Soon Warning Light)
- Engine hesitation

Possible causes
- Harness or connectors (EGR volume control valve circuit is open or shorted.)
- EGR volume control solenoid valve
- EGR temperature sensor and circuit

Possible solution
- Repair EGR harness or connector
- Replaced EGR volume control solenoid valve
- Replaced EGR volume control valve
When is the code detected?
- An improper voltage signal is sent to ECM through the valve


Hope helps.

Mar 06, 2011 | 2005 Dodge Ram

1 Answer

How do I install an EGR valve for 2005 dodge durango?


To install the EGR Valve on a 2005 Durango first it is necessary to remove the air intake hoses and palce them to the side. Next, in order to get the EGR valve you will need to remove the windshield wiper motor, which is a pain but necessary to do get to the EGR valve. After removing all of the itemsthat are in the way you will be faced with a task that will try your patience, the EGR valve is located on the right side of the motor, (as if you were facing the motor from the front) just behind and to the rear of the throttle body. After you locate it you will need a rachet with a flexible head because it is fairly difficult to reach otherwise. A mirror and light will also help so you can see what you are doing since the EGR valve is located in such a hard place to see and get to that you will only be able to see part of it while you are removing the screws. After removing the EGR valve, simply reversethe procedure and your done. P.S. I own a 2005 Dodge Durango SLT with a 4.7L engine and I replaced mine this year after a check engine light came on and I checked the code on the OBD. By the way the EGR valve is a pain in the rear to change. Good luck!

Jun 29, 2010 | 2005 Dodge Durango

1 Answer

Were is the egr valve located for mazda rotege5


2002 Mazda Protege5 with the FS2.0 Motor. The EGR Valve is located below the throttle-body. You must take off the Intake tube to get a good view of it. To replace it I think you might have to take off the throttle-body.

0335fe8.jpg

Fig. Exploded view of the intake manifold assembly with 2.0L (FS) engine

Good luck (remember rated this).

Jun 25, 2010 | 2003 Mazda Protege

1 Answer

Were do i fine egr on the motor


I just replaced the EGR valve on my exact vehicle to yours. Everything perkins48 stated on the EGR location is good but let me add a few items if I can. The EGR valve looks like a flying saucer with a small hose attached to it. It has two bolts holding it in at its base.There is also a pipe screwed in from the lower front side base that leads to the exhaust manifold. There are a few sensors that have to be unplugged and the housing for the air filter assy. has to be unbolted but a relatively easy job once EGR is located. Hope this info helps you.

Mar 15, 2010 | 1996 Ford Windstar

2 Answers

Egr valve needs replacing


Get the correct egr valve and when You see how it looks like You will be able to identified it is on the top some where on the side

Jan 22, 2009 | 1991 Acura Integra Hatchback

Not finding what you are looking for?
2005 Chrysler Town & Country Logo

152 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8269 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...