Question about 1995 Ford F150 Styleside Regular Cab

1 Answer

Need to know where the number one plug is located on the distributer cap

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 394 Answers

Hi,A Lot of caps have the #1 molded right on the cap itself.
Good Luck !!!!!!!!!!!!!

Posted on Jul 14, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i find the posiyion of 1st cylinder to put in new distributer for a 98 4.3 blazer distributer wasnt marked when took out


pull out number 1 plug and put a straw or soft object in hole. turn engine by hand on front crank. when the straw or similar is on the very top, just before it goes down ! this is top dead center, then put in distributor with the rotor button facing the number 1 wire on distributor cap, replace number 1 plug and adjust the distributor, buy turning it after it is installed in vehicle.and vehicle is running. if you do not know where number 1 plug is. call the auto parts store. they should be able to tell you. auto-zone etc. good-day !

Jan 15, 2012 | Cars & Trucks

1 Answer

I need to know where the spark plugs and distributer cap is located on my 1998 Lexus es300


Hello,the Lexus 3.0 litre engine has no distributor or cap.There is an individual ignition coil on top of each spark plug,all of which are located on top of the engine.There may be a removeable trim cover over the engine making these harder to see untill you remove it for access.
John.

Sep 04, 2011 | 1998 Lexus ES 300

2 Answers

I mixed the distributor cables up,so i need the order to correctly connect


If the wires are still in the distributer, AND, if you have a stock intake manifold, the firing order is on the manifold. If it's a V-8, the number 1, 3, 5, & 7 plugs are on the drivers side of the engine. The number 2, 4, 6, & 8 plugs are on the passenger side. The number 1 plug wire can be located by looking at the distributer from the front of the engine and visually looking between the distributer and the number 1 plug. Visualize the distributer as a clock. The number one position should be located between 4 and 5 o'clock and should have the longest wire of those on that side of the distributer.

If the wires have been pulled from the distributer, then, then, remove the rotor cap, turn the engine over slowly until the rotor is pointing to the number 1 plug. Using the firing order on the intake manifold, starting with number 1, replace the wires going clockwise around the distributer.

Apr 09, 2011 | Chevrolet Chevy Cars & Trucks

2 Answers

I need to know where number one is on the distributer cap for the firing order on a gmc 350 1989 truck


The postion of the #1 plugwire may not be the same as factory origional location, and that is not necessarily an issue....
Pull the # 1 spark plug, ground coil wire, put your finger over the plug hole and have a helper bump the starter over in short bursts.

When on the compression stroke, lots of air wants to rush out of the plug hole. This may take a few times before you get it, then look at the timing marks, to be sure you are close.... Then pull the distributer cap and the rotor will be pointing to the #1 plug wire position.

Feb 07, 2011 | Chevrolet Chevy Cars & Trucks

1 Answer

How to replace distributer cap and rotor button on 96 Acura TL ?


Locate the distributer cap. Mark all your spark plug wires with some tape and number system so they go back in the same position (on the new cap). Remove the spark plug wires from the old cap (after marking them) and lay them to the side. Remove the 2 Torx or Phillips screws from the cap. Lift the cap up and off. The rotor will be directly under the cap. Lift it up and off. This may take a little rocking motion while pulling on it to get it off. Align the new rotor on the shaft and push it on firmly. Place the new cap on and install the 2 screws removed earlier. Install the plug wires on the cap in the order they come off. Ensure the wires are pushed in firmly.

Jan 30, 2011 | 1996 Acura TL Series

1 Answer

I need to know what the order on the distributor cap in for the plugs are I know the firing order I just go the last two wires mixed up on the drivers side so I know it's 1-3-5 but where are the locations...


You need to determin which direction the rotor button turns when the engine is running. Take the cap off and get someone to bump the starter . Watch the rotor. If it turns counter clockwise the fireing order will follow its order counter clockwise on the distributer .In other words # 1 wire on the distributer goes to # 1 spark plug. Then the next wire counting counterclockwise goes to # 3 plug . Follow the firing around the distributer for all the wires. counter clockwise is the oppisit to the rotation of the hands on a clock .

Oct 21, 2010 | Chevrolet C1500 Cars & Trucks

1 Answer

What are the numbers on a distributing cap


engines have a fireing order for each piston like 18436572 for an eight cylinder the distributer cap will have eight spark plug wire connections starting with number one connect plug wire to number one cylinder then moveing clockwise around the capconnect plug wire to the number eight cylinder untill all wires are connected in order to the right cylinder

Feb 16, 2010 | 1989 Saab 9000

1 Answer

Timing on distribuitor


turn the engine so the bottom pulley mark is on top dead centre make sure the piston is up check by removing number 1 spark plug remove the distributer cap and refit distributer with rotor button pointing to number 1 on the distributor cap that will fix your problem let me know if you get stuck

Jun 13, 2008 | 1994 Ford F150 Styleside Supercab

Not finding what you are looking for?
1995 Ford F150 Styleside Regular Cab Logo

Related Topics:

34 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...