Question about 1993 Ford Bronco

1 Answer

Can I eliminate the pollution pump and hardware on a 93 ford bronco. Just rebuilt it and want to put on headers, would like to take off all of the pollution, will it effect anything like the computer or efi

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 27 Answers

Yes, the computer has several points that it uses from the pollution items it uses to adjust air fuel mixture ect. you should be able to do it but you will always have codes from the missing items and it may not run as smooth as it should.

Posted on Aug 01, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do u change a starter in a 93 ford bronco


The first thing you want to do is disconnect the battery cables. the starter is going to be on the passenger side where the transmission mates to the engine. You will remove two bolts that hold the starter in. I would definitely have the starter tested or tested myself which is very common and very simple to do. Prior to replacing with a new or rebuilt model

Jul 12, 2014 | 1993 Ford Bronco

1 Answer

88 Ford Bronco II 2.9L I'm replacing my water pump


Buy a gallon of 100 percent,mix it 50-50 with water to make 2 gallons,may be enough.

Dec 22, 2012 | Cars & Trucks

1 Answer

Need spark plug diagram for 93 Bronco


Hi there:
You have several engine sizes there:

1993 Ford Bronco Full Size 4.9 liter L6 VIN "Z"

6_3_2012_1_09_49_pm.gif



1993 Ford Bronco Full Size 5.0 liter V-8 VIN "N"

6_3_2012_1_10_39_pm.gif



1993 Ford Bronco Full Size 5.8 liter V-8 VIN "H"


6_3_2012_1_11_20_pm.gif



Hope this hesl; remember to rating this answer.

Jun 03, 2012 | 1996 Ford Bronco

2 Answers

What parts of the engine does the serpentine belt drive?? alternator ect.


Power steering, water pump, a/c, altenator, & pollution pump if equipt

Mar 30, 2010 | 1990 Ford Bronco

1 Answer

1990 Ford Bronco, 302 v8 (5.0), AOD Auto Transmission, Edelbrock Intake, headers, 23Lb injectors. Truck will start anr seems to run fine but dies when put into gear, acts like there is a dead spot when I...


is your computer inside the engine compartment? if so i am geussing it got coolant on it also and is keeping the injectors open and running the pump when it should be off.

Jan 25, 2010 | 1990 Ford Bronco

4 Answers

Engine turns over but does not start .how to change the fuel pump?


does it start if you spray starting fluid down the intake?

Nov 08, 2009 | 1993 Ford Bronco

1 Answer

302 v8 on a 76 ford bronco just rebuilt has


sounds like your timing is way off,if no timing gun and you dont have specs,loosen your distributer a bit and rev your engine to about3000 rpm and just listen to the engine while you slightly turn the distibuter until it is the smoothest sounding with no sputtering then tighten your distributer back up or pay the bucks get it timed at a shop its cheap

Oct 19, 2009 | 1981 Ford Bronco

1 Answer

Bought a 88 Ford Bronco 2 yrs ago, 302 FI running rough again.


Put some ethernol treatment with stabilzer in it..
Change the fuel filter, air filter and give it an oil change...
If you can do it yourself do a trani service..

Sep 21, 2009 | 1988 Ford Bronco

1 Answer

I have a 1975 Ford Early Bronco that has been sitting for 20 yrs


Change plugs & wires, New battery , Install radiator. Crank it over if it starts and is smoking needs new vale guide seals and maybe new rings. But try to get it started first then go from there. If it wont turn over try to turn over by hand from front crank pully with socket and breaker bar to free up motor.

Mar 30, 2009 | 1981 Ford Bronco

1 Answer

1994 Bronco Egr valve doesnt fit into new ****** headers


They sold you a set of headers that don't accommodate the EGR valve line. You can buy headers that have the bung welded into them for the connection. If you do not connect the EGR then you exhaust gas temps will run high and pinging will likely be the result. Excessive preignition can cause valve and piston damage. The lack of the EGR valve may cause you to not pass your states emissions test. I would purchase a set of headers that have the hook up on them. Try Gibson headers. They sell these.

Feb 17, 2009 | 1994 Ford Bronco

Not finding what you are looking for?
1993 Ford Bronco Logo

Related Topics:

103 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...