Question about 1992 Ford Tempo

1 Answer

Need to run a scan on 92 ford tempo. How do I hook a code reader up. I know where the test site is but there is a hard plastic cover and wondering if I need to remove it to hook device up

Posted by on

  • kap Jul 14, 2010

    figured it out. please disregard

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 659 Answers

Yes you have to remove the cover

Posted on Jul 15, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 1986 ford tempo GL 2.3L throttle body injection vin with a X my problem is when I make a right turn my car tries to stall and when I slow down to stop then it only goes 35 up steep hills


You need to check the fuel pressure and run an EEC-IV fault code tests both the running test and the passive key on engine off test. To run the fault code test using the check engine "blink" method go to the link below. The diagnostic connector is under the hood it is a red triangle shaped connector, it may have a cover on it that is black, it just pulls out of the cover.

EEC IV Self Test Ford Fuel Injection and EEC IV Electronic Engine Control...

Nov 17, 2016 | Ford Cars & Trucks

1 Answer

Where do i hook up the engine code reader on 89 ford tempo.t


The universal OBDII code reader came out in 1996 per government mandate. Before that time, OBDI was the first vehicles with computers, and every manufacture was doing their own thing and creating their own vehicle specific testers or using lights on the computer to read codes. So you will not be able to ready the codes on your pre '96 vehicle. You would have to take it to a shop that has the special equipment to read the codes or get a service manual with flow charts to walk you through reading the codes off the side of the computer. Hope this helps. Good luck :O)

Feb 17, 2011 | 1989 Ford Tempo

1 Answer

I own a 1992 ford tempo gl 6cyclinder.First notice proble" 2months ago on a sudden take off engine light came on.All maintance on car get serviced on time.Now after a few minutes engine light just...


A quick take off can "blow the cobwebs out" on older motors. Chances are if the car still runs good it is an O2 sensor on your exhaust. Wouldn't worry about it other than having to pass smog tests. Over heating problems could be a thermostat or head gasket problem that could ruin your motor. If you don't have a temp gauge talk to a parts store about having a code reader hooked up, most will do it for free.

Feb 13, 2011 | 1992 Ford Tempo

1 Answer

Replaced neutral switch in 92 ford tempo. now the


Did you knock the linkage off from the throttle body to the transmission right above the neutral safety switch?

May 17, 2010 | Ford Tempo Cars & Trucks

1 Answer

Need to know where the temperature wire hooks up on the 92 ford tempo engine


The sender should be near the thermostat housing on the cylinder head.

Sep 25, 2009 | 1992 Ford Tempo

1 Answer

Need ignition key code lost keys in my house fire burnt to the ground cnt find the spares


key code is on metal tag or plastic tag in glove box with owner manual packet. Also, dealer who sold car new has code in sales folder.
ALso, call Ford Customer service. They may have it. Kind of old though, but try.

May 12, 2009 | 1992 Ford Tempo

1 Answer

Ford code reader won't fit test plugs on my 1990 F250


under dash by steering column past the plastic that covers lower dash and get a code reader .

Dec 31, 2008 | 1990 Ford F250

1 Answer

Battery draining fast


I would check the alternator again, it apparently isn't charging the battery with engine running. You need a volt meter or amp meter to test this. Also does the battery discharge when the car is not running?

Aug 07, 2008 | 1992 Ford Tempo

3 Answers

F150 1992 check engine light


On a Ford system you need a code reader, no other way. The plug is under the steering column.

Aug 04, 2008 | 1992 Ford F150 SuperCab

Not finding what you are looking for?
1992 Ford Tempo Logo

Related Topics:

113 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5467 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...