Question about 1999 Lincoln Town Car

Open Question

Removal of intake manifold on 1999 lincoln town car

How do I get to the rear bolts on the intake manifold of my 99 Lincoln Town Car. I have all the top accessories removed, and evidently all but a couple of manifold bolts. There is a bracket over the rear of the fuel rail on the driver side, and a manifold bolt under the bracket. Where
are/is the bolt holding the bracket, and/or how do I work around the bracket?

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
Mr BrokRench
  • 1623 Answers

SOURCE: heat wont work 2001 lincoln town car cartia

Hello Callahan5922....this sounds like a stuck blower motor resistor. I assume the blower won't function in the a/c mode either? If you have a digital multimeter you can check this. I believe it's fuse #2....if the digital indicator goes up or down when you increase or decrease the fan speed thats good. Locate the blower motor resistor....you wil find it located on the fire wall behind the right valve cover hiding behind the heater hose, it's about the size of a cigarette pack. With the engine off, and key in on position, turn the A/C on High, and rap a tap tap tap on the resistor. You might be suprised when the blower motor takes off a runnin,
I hope this is the answer you need and i was able to help solve this for you. Good luck...

Posted on May 13, 2009

Ad
  • 5 Answers

SOURCE: 1997 lincoln town car 4.6 with a p0430 fault code

I will make an assumption here, we know what the root word means. This code was extracted from the computer by? What this is telling you one of 2 things: The Bank 2 oxygen sensor down stream of the catalytic converter (there are 2 converters, one for each bank of cylinders on the 4.6ltr engine) is bad and/or that the Bank 2 catalytic converter is no longer doing the job it was designed to do. Simply, Catalysts wear out. They are good for approx 100,000 miles (as required by Federal Law). Again, I assume that the reason the intake manifold was replaced was because it had a crack in one, or more, of the runners? (part that feeds the head of a manifold). It may have taken a while to find this as being the cause of why the car running incorrectly, maybe rough. This means, that during the time the car was being driven with the problem, the amount of unburned, or not within spec exhaust gases, coming off the side of the engine affected by the intake issue was higher than normal. This out of balance level of exhaust gases were being dumped into the converter on that side of the engine, thus causing the converter to have to run hotter, work harder, or even at the time the gas was being processed through, causing deposits to be formed in the converter, thus shortening it's life span. The Bank 1 side of the engine, apparently, did not have the issue and it's catalytic converter's life was not affected. I hope this makes sense to you.

Posted on Aug 19, 2009

old marine
  • 1983 Answers

SOURCE: need routing diagram for 2000 lincoln town car serpentine belt

There's a diagram at this link.

Posted on May 11, 2009

co7196
  • 3433 Answers

SOURCE: 2002 Lincoln Town Car AC Blower Motor Relay Location

Relays are normally located under the hood in a protective plastic box. Good Luck Ned

Posted on Oct 06, 2009

centralvalle
  • 386 Answers

SOURCE: HOW TO REPLACE INTAKE MANIFOLD ON A LINCOLN

answer , very carefully ...

drain coolant , remove and mark all vacuum lines , make a schematic to diagram your hose routing, disconnect and plug all fuel lines, remove distributor and mark location of rotor, disconnect battery, remove any necessary cables, brackets and or accesseries, remove intake mounting bolts, note length of bolts and reference location, pry up on intake , remove intake, scrape old gasket off , must be very clean to reinstall new gasket or you will cause a leak..

Posted on Nov 02, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Location of throttle body vaccum 1999 lincoln town car, what goes to where I'm pointing?


to the intake manifold I have the same car I will take a picture if you do not find it

Feb 07, 2017 | 1999 Lincoln Town Car

1 Answer

99 Lincoln Town Car....how to replace the driver's door on the town car?


All vehicles are pretty much the same with replacing a door. There will be bolts holding it on when you open the door, unplug the electrical and take off the bolts.

Nov 03, 2016 | 1999 Lincoln Town Car

1 Answer

How do you remove a fuel injector on a "99 lincoln town car,


no for the injectors you need a special tool to remove the fuel lines

Oct 20, 2014 | 1999 Lincoln Town Car

1 Answer

1999 lincoln town car jerks when driving help


I have already answered this on a duplicate post of yours.

Jun 25, 2012 | 1999 Lincoln Town Car

1 Answer

I need to know the torque for an intake manifold for a 86 lincoln town car


The torque specification for the intake manifold retainer bolts on a 1986 Lincoln Town car equipped with a 5.0L or 5.0L HO V-8 engine is 23 - 25 Ft. Lbs. ( 31 - 34 N.m)

Jun 02, 2012 | Lincoln Town Car Cars & Trucks

1 Answer

What size wrench do I need to remove the rear bolt on the bracket over the fues rail replacing the intake manifold?


I'm sorry but I do not know what size wrench you need for that. You might call a Lincoln dealership and see if they know. A workshop manual might also have that information. Good luck!

Dec 26, 2011 | 1999 Lincoln Town Car

2 Answers

HOW TO REPLACE INTAKE MANIFOLD ON A LINCOLN


answer , very carefully ...

drain coolant , remove and mark all vacuum lines , make a schematic to diagram your hose routing, disconnect and plug all fuel lines, remove distributor and mark location of rotor, disconnect battery, remove any necessary cables, brackets and or accesseries, remove intake mounting bolts, note length of bolts and reference location, pry up on intake , remove intake, scrape old gasket off , must be very clean to reinstall new gasket or you will cause a leak..

Nov 02, 2009 | 1999 Lincoln Town Car

1 Answer

How do i pull my rear axle to change my wheel bearing in 99 lincoln towncar?


Besides removing the rear drum and taking out the bolts that hold the dust cover. You will have to remove the cover from the rear end housing. The axel has a retanning clip inside.

Oct 18, 2009 | 1999 Lincoln Town Car

1 Answer

1999 lincoln town car fuel gage not working


99% of the time this is due to a defective gas gauge sending unit, this is located in the gas tank.

May 01, 2009 | 1999 Lincoln Town Car

1 Answer

Where is the thermostat located on a 1996 Lincoln Town Car?


The thermostat is in the housing bolted to the intake that the upper radiator hose goes to. Check the Intake manifold for leaks, these are prone to cracking the Intake. Check the front crossover behind the alternator and check the rear where the heater hose is hooked.

Mar 11, 2009 | 1996 Lincoln Town Car

Not finding what you are looking for?
1999 Lincoln Town Car Logo

Related Topics:

264 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lincoln Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

fordexpert

Level 3 Expert

5520 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Lincoln Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...