Question about 2000 Buick LeSabre

1 Answer

WILL REPLACING A FRONT ROUND MOTOR MOUNT STOP MY 2000 LASABRE FROM STUTTERING AND MISSING

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 3,092 Answers

No you have a cylinder misfire, check for possible tune-up.

Posted on Jul 14, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you replace engine mount on 2000 buick


Put car on jackstands so you can work under car. Put 2 inch thick 5": x 5" wood board on jack under oil pan. Jack up slightly. Unbolt broken mount & replace with new one.

Oct 22, 2013 | 2000 Buick LeSabre

1 Answer

Engine vibrates when car is in gear


have you done any other work, trans mount, recheck all bolts, exhaust has its flex pipe? I may be wrong but front and rear mounts are sloted are they set properly, also top side mount have two big washers or insolators on each side are there missing? this will cause a vibration. good luck

Oct 10, 2012 | 1997 Toyota Tercel

3 Answers

Replace blower motor on buick lesabre 2004


It is located under the right side off the dash. Remove the plastic kick panel and you will see it. The screws to remove the panel are just under the glove box. Once the panel is removed you will see the motor housing it has an electric plug with three wires.

May 25, 2012 | 2004 Buick LeSabre

1 Answer

My car enginee virbrate what is the cause


If the motor seems to be running right, not missing or stuttering I would assume a worn or broken motor mount. At almost 9 years old if they are still OEM mounts that would be reasonable.

Feb 15, 2011 | 2002 Volkswagen Jetta TDI

1 Answer

2000 buick regal....The car seems like its either missing or loosing power when making a hard right turn and pressing gas. when i get off the gas its fine. It sometimes does this when driving straight, but...


A motoe mount would not let it loose power. It would however make the motor shake causing the eddect of it missing. Check the main motor mount that attaches the motor to the frame that is in front on the car just above the radiator. It has a large rubber bushing that sometimes goes bad on this vehicles. I have included a picture of what it would look like.

electricdime_3.jpg

Dec 06, 2010 | 1999 Buick Regal

1 Answer

Replacing serpentine accessory belt. Is it necessary to remove motor mounting brace to remove and install new serpentine belt?


From my understanding I think you have to remove the motor mount and mount the engine to remove it because I have been asking different mechanics about the serpintine belt on my 1998 Buick Lasabre.

Nov 28, 2010 | 1998 Buick LeSabre

2 Answers

My jeep starts shaking violently when it reaches 55 miles/hr.


no its your wheels well out of balance get them looked at first fitting a damper wont stop this shimmy

Jun 04, 2010 | 2000 Jeep Grand Cherokee

3 Answers

I have a 95 Buick LeSabre and it recently started vibrating when I accelerate. I started only happening when i got to about 50 MPH but has steadily gotten worse. If I let off the accelerator it stops....


check the tires for separations or bulges in the tread face also check the drive axles see if the boots are torn or missing all together,also be sure to check the ball joints and tie rod ends.

Dec 26, 2009 | Buick LeSabre Cars & Trucks

1 Answer

2000 buick lasabre misses when idling


Replace plugs and wires at the same time and avoid carbon tracking miss.

Mar 26, 2009 | 2000 Buick LeSabre

Not finding what you are looking for?
2000 Buick LeSabre Logo

Related Topics:

225 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8270 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...