Question about 2004 Honda Odyssey

Open Question

How to remove sliding door trim to grease door track

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Drivers door glass DOSENT drop quick enough when opening door, making the glass spring off the seal on opening


Whenever a power window opens & closes slowly it's usually one of two things. It could be that the window is sticking in the forward vent glass trim (or whatever trim is holding your window while raised), or a sign that the tracks and slide mechanism are getting gummed up. You can lube the channels holding the raised window with silicone - I use a product called Shin-Etsu developed by Honda. It's available on Amazon and other online stores.

For the mechanism and rollers you usually need to remove the door card to get at them. If mechanics have kept adding more and more grease over the years you might need to clean it all out and apply a fresh coat of grease. You can again use Shin-Etsu or the more commonly available white lithium grease.

May 10, 2015 | 2002 Peugeot 307

2 Answers

Why does the sliding back door always sticks and won't open in the winter?


grease will get hard like wax in the cold spray areas that are greased with carb or brake cleaner to remove the grease and relube those areas with a teflon or silicone type of lube spray

Nov 18, 2014 | 1999 Dodge Caravan

1 Answer

Need to replace sunroof..


you need to replace glass or is it leaking if leaking then you have to remove upper seat belt covers pop off remove bolt 14mm and the trims on upper pillars pry off carefully held in by clips remove covers on interior light at front where sunroof switches are there are screws by bulbs disconnect connector remove center light cover and screws disconnect connector with clean hands remove rbber trim around sunroof opening and plastic cover on each side of sunroof glass held on with plastic screw clips then remove four 10mm nuts lift sunroof glass out of car remove cover and screws from rearview mirror all plastic trims around headliner move pass seat forward most and flip back rest all way down roll pass window fully down then slide headliner out of car now you can remove electrical connectors and remove water flow hoses from sunroof unit remove 8 12mm nuts holding frame to roof remove through door you will see the track sunroof slides on remove nuts along problem is silicone between track and frame is deteriorated lift track clean replace silicone reattach frame to roof dont put trims or liner in till test connect switches and glass to frame make sure sunroof works and closes fully then go through car wash to see if leak is fixed

Jan 13, 2011 | 2001 Subaru Legacy

2 Answers

How do i change my driver side door my van is a 1994 plymouth voyager


first you go to local book store or dealer or ebay and pick up a chilton or haynes book it will come in handy for the wiring and the hinge torque and allinment specs and tricks

Jan 23, 2010 | 1994 Plymouth Voyager

1 Answer

Removing exterior panel covering track for center roller on sliding door


exterior panel is not removable. to access center roller,remove screws & clips from interior door trim panels remove roller cover panel inside door.loosen bolts to adjust roller,remove bolts to replace it.

Oct 13, 2009 | 1992 Plymouth Voyager

1 Answer

Fallen driver's side window


probably need a new window regulator. ebay. 93 to 98 should fit.

Section 01-05: Trim, Interior 1998 Villager Workshop Manual
REMOVAL AND INSTALLATION Trim Panel(s), Door Front
Removal
  1. Disconnect the battery ground cable (14301) if equipped with power locks or power windows.
  1. swv~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Use care when removing the front door inside handle escutcheon (22620). Failure to do so can result in damage to the component.
    Carefully pry off the front door inside handle escutcheon by inserting a standard 1/4 inch screwdriver between the top rear portion of the front door inside handle escutcheon and the front door trim panel (23942) .




  1. If equipped with manual windows, slip a clean shop rag between the window regulator handle (23342) and the front door trim panel .
  1. Pull the shop rag back and forth to release the window regulator handle clip.




  1. Remove the three cover caps and front door trim panel screws.
  1. Remove the one front door trim panel capped screws from the door pull handle.
  1. If equipped with power windows, remove the door pull handle. Disconnect the electrical connectors.
  1. Slide a flat-bladed tool behind each of the retainers and twist the tool to disengage the front door trim panel from the front door (20124) .
  1. Remove the front door trim panel.
Installation
To install, reverse the removal procedure.
---------------------------------------------------------
Window Regulator, Power Front Door
Removal
  1. Disconnect the battery ground cable (14301) .
  1. Remove the front door window glass (21410) . Refer to the front door window glass removal procedure in this section.
  1. Remove the two front door brace bolts and the front door brace.


    415712f.gif

  1. Disconnect the front window regulator electric drive electrical connector.
  1. Remove the four front door window glass regulator track bolts.

    67b6136.gif


  1. Remove the three front window regulator electric drive bolts.
  1. Remove the front door window glass regulator track and the front window regulator electric drive (23394) as an assembly through the opening in the front door (20124) .
Installation
  1. Install the front door window glass regulator track and the front window regulator electric drive as an assembly through the opening in the front door .
  1. Install the three front window regulator electric drive bolts. Tighten the front window regulator electric drive bolts securely.
  1. Install the four front door window glass regulator track bolts. Tighten the front door window glass regulator track bolts securely.

Apr 29, 2009 | 1998 Mercury Villager

1 Answer

The seat belt gets stuck and makes a loud and distracting noise


The system can be operated manually by removing round cover cap on the B pillar (Just behind door). manually turn crank knob on top of motor.

There is a limit switch on the A pillar to turn off the motor for forward movement. There is a limit switch on the B pillar to shut off the motor for rearward movement.

You may need a B pillar limit switch if the belt is going all the way back but not shutting off. Unfortunately the rear limit switch is serviced with the track & motor assembly. Get a used one at car-part.com. Page with * is cheapest part.


You need to remove A pillar trim, B pillar lower trim, B pillar upper trim, and front door opening upper trim.

disconnect front limit switch
disconnect rear limit switch
disconnect motor electrical connector
remove 3 motor bolts
remove 2 limit switch bracket bolts
remove screw at A pillar near limit switch
remove 3 screws at track assy to roof.
pull back carpet & remove 4 screws at floor where you step into car.
remove track & motor assy.

Apr 10, 2009 | 1993 Mercury Villager

1 Answer

Front door panels


yes you need to remove the door panel and here is the instructions via TIS (Toyota info system)

DISASSEMBLY
1. REMOVE THESE PARTS:
HINT:
Tape a screwdriver tip before use.
(a) Door inside handle bezel
(b) Armrest
(c) Armrest panel base upper
(d) Courtesy light
(e) Lower frame bracket garnish
2. REMOVE DOOR TRIM
(a) Remove the 3 screws from the door trim.
(b) Using a screwdriver, remove the clip and remove the trim
by pulling all of the trim up.
HINT:
Tape the screwdriver tip before use.
(c) Remove the 11 screws and armrest base from the door
trim.
(d) Remove the inner weatherstrip from the door trim.
(e) Remove the 8 screws and door pocket from the door trim.
3. REMOVE THESE PARTS:
(a) Door belt moulding
HINT:
Pry out the clip from the edge of the panel, and remove the
moulding .
(b) Door weatherstrip
NOTICE:
Do not pull strongly on the weatherstrip as it may tear.
(c) Door inside handle
(d) Door lock control relay
(e) Service hole cover
BO2455
Cotton
Tape
Panel
Cover
BO−10
BODY − FRONT DOOR
NOTICE:
Do not block the trim clip sealing with the tape.
(f) Outside rear view mirror
(g) Door glass run
(h) Rear lower frame
HINT:
Adjust the equalizer arm up to down and tighten if where dimensions
A and B, as shown are equal.
(i) Door glass
(j) Window regulator
Torque: 5.0 N·m (50 kgf·cm, 43 in.·lbf)
HINT:
Apply MP grease to the sliding surface and gears of the window
regulator.
NOTICE:
Do not apply grease to the spring.
(k) Locking and opening control link
(l) Door lock
HINT:
Apply adhesive to the 3 screws.
Part No.08833−00070, THREE BOND 1324 or equivalent
Torque:5.0 N·m (50 kgf·cm, 43 in.·lbf)
BODY − FRONT DOOR
BO−11
HINT:
At the time of reassembly, apply MP grease to the sliding surface
of the door lock.
(m) Door outside handle
(n) Door lock cylinder
(o) Door speak

Mar 08, 2009 | 1997 Toyota Land Cruiser

1 Answer

How do you remove the door panels on a 1995 mercury villager


http://autos.groups.yahoo.com/group/villagerquest/

you have to remove the cup behind the door handle. rmove screws aroun the door pull. get a screw driver and pry the trim panel away from the door carefully. There is a plastic christmas tree clip every 6 inches. when the bottom & sides are free, lift up the trim panel to get it out of the track at the base of the window.
--------------------------------------------------------------------------------------

Carefully pry off the front door inside handle escutcheon by inserting a standard 1/4 inch screwdriver between the top rear portion of the front door inside handle escutcheon and the front door trim panel (23942).

  1. Remove the three cover caps and front door trim panel screws.
  1. Remove the one front door trim panel capped screw from the door pull handle.
  1. If equipped with power windows, remove the door pull handle. Disconnect the electrical connections.
  1. Slide a flat-bladed tool behind each of the retainers and twist the tool to disengage the front door trim panel from the front door (20124).
  1. Remove the front door trim panel.

Jan 04, 2009 | 1995 Mercury Villager

Not finding what you are looking for?
2004 Honda Odyssey Logo

Related Topics:

311 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

77169 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22258 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...