Question about 2003 Dodge Intrepid

1 Answer

How do i change the cam positioning sensor on my 2003 2.7 dodge intrepid

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 10 Answers

Quick fix. No worries. There is 1 bolt and one wire connector for the camshaft postioning sensor. The sensor is located on the front of the block just slightly off center toward the drivers side. An easy to find out which one it is (because there are a few wierd little sensor things around it) is to buy the new one and look in that area until you find a match to the part in your hand. Be careful to not break the wiring harness when removing.

Step 1: Find the sensor (hardest part)

Step 2: Remove the (1) bolt holding it into the engine block

Step 3: Remove the wiring harness from the old sensor

Step 4: Plug the wiring harness into the new sensor

Step 5: Replace the bolt and snug the sensor in place

Step 6: Using an OBD2 (II) sensor. Turn your check engine light off.

NOTE: You must turn the check engine light off. Simply changing the sensor will not turn off the light.

Posted on Sep 29, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2001 dodge intrepid .sometimes will crank and then won't .changed crank sensor,cam sensor, fuelpump and computer.any ideas


it is cranking ( turning over ) but not starting
check the cam shaft position sensor wires . immobilizer operation

Apr 16, 2017 | Dodge Cars & Trucks

1 Answer

Cam sensor


On front of the timing covers...

Apr 21, 2014 | 2003 Dodge Intrepid

1 Answer

I have a 2001 dodge intrepid. I just replaced the output speed sensor. It is still stuck in limp in mode.


There is a recall on some intrepids for the cam position sensor. You may have to change the cam sensor, if you don't have a code for it, don't change it. You might have to go to the dealer and have them flash your computer with a scan tool. that may be covered under the recall. I would investigate if I were you.

I hope this helps

Aug 06, 2010 | 1998 Dodge Intrepid

1 Answer

How to change cam positiom sensor in 2000 dodge


The cam position sensor on the 2.7 engine is on the
driver side of your engine, right in the front of the head. there's a 10mm bolt. undo the bolt and pull it straight out. push the new one into the hole, and hold pressure on it until it's bolted back in.

If you have the 3.5, the cam position sensor is located on top of the timing cover. I just unbolt the upper intake just enough to lift it up a little. unbolt the cam sensor, pull it out and install the new one keeping pressure on it until it's bolted in.

I hope this helps

May 13, 2010 | 2000 Dodge Intrepid

1 Answer

Locate cam position sensor on 2004 dodge intrepid


The camshaft position sensor is mounted to the top of the timing case cover.

Oct 25, 2009 | 2004 Dodge Intrepid

1 Answer

Where is the camshaft position sensor on a dodge intrepid 2003


where is the camshaft position sensor on a 2000 dodge intrepid 2.7L V6

Oct 16, 2009 | 2003 Dodge Intrepid

1 Answer

Where is the camshft position sensor on a 03 dodge intrepid 2.7l Bank A


THE CAM SENSOR IS LOCATED IN LEFT(DRIVER'S SIDE) CYLINDER HEAD AT THE FRONT..1 BOLT AND A 3 WIRE CONNECTOR..REMOVE BOLT AND PULL SENSOR OUT TOWARD FRONT OF VEHICLE..YOU MAY HAVE TO WIGGLE SENSOR TO REMOVE..PICK UP A NEW ONE AND YOU WILL SEE WHAT IT LOOKS LIKE..PRETTY EASY TO REPLACE AND IS FAIRLY COMMON PROBLEM

Aug 29, 2009 | 2003 Dodge Intrepid

3 Answers

2002 dodge intrepid starting issue new water pump,new timing chain,new belts, good spart, valves are good Can it be a crankshaft sensor?


dear friend-if you are positive that all the repairs were carried out with great care,that the timing is right,and you got spark and fuel,all the valves close propely,then it should start,if the sensor was ok before you stripped the engine why should it be faulty now.

Jun 29, 2009 | 2000 Dodge Intrepid

1 Answer

Help 2003 dodge intrepid


i would check into the vehicle speed sensor and the gear shift lever position sensor

Jul 22, 2008 | 2003 Dodge Intrepid

Not finding what you are looking for?
2003 Dodge Intrepid Logo

192 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8172 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...