Question about 1995 Ford F250

1 Answer

How do you remove the dash in a 1995 ford f-250

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 17,970 Answers

1992-96 Vehicles

how do you remove the dash in a 1995 ford f-250 - 41443a4.jpg

Fig. : Instrument panel installation-1992-96 vehicles

CAUTION On vehicles equipped with air bags, please refer to Chassis Electrical for arming, disarming and precautions. Accidental deployment of the air bag system can cause serious personal injury.

  1. Disconnect the negative battery cable.
  2. Unplug the connectors from the instrument panel rear lamp wiring and the engine control sensor wiring in the engine compartment by loosening the bolts and separating the connectors.
  3. Remove the radio as outlined
  4. Remove the right and left side windshield side garnish moldings.
  5. Remove the 4 screws attaching the top of the instrument panel to the cowl.
  6. Remove the 2 screws attaching the instrument panel steering column opening cover assembly to the underside of the instrument panel.
  7. Remove the cover by pulling up at the top of the cover and unsnapping the 4 retaining clips.
  8. Pull the antenna lead-in cable down and unsnap the wire from the bottom of the instrument panel and lay the wire down on the floor out of the way.
  9. Remove the bolt attaching the instrument panel to the panel brace. Some vehicles may have 2 lower braces.
  10. Remove the screw and washer assembly located at the lower corner on the right side of the instrument panel.
  11. Unplug the wiring connectors from the main wiring harness at the right cowl side panel.
  12. Unplug the wiring connector from the parking brake control.
  13. Remove the 3 nuts attaching the parking brake control to the left side cowl panel and lay on the floor. Do not disconnect the parking brake cable.
  14. On vehicles with column shift; disconnect the shift cable from the steering column shift cable bracket.
  15. Unplug the wiring connector from the brake light switch.
  16. On vehicles with manual transmission; unplug the wiring connector from the clutch interlock switch.
  17. Unplug the wiring connectors from the main wiring harness at the left cowl side panel.
  18. Remove the pinch bolt from the steering column to the lower steering column shaft. Move the lower steering column shaft toward the engine and separate from the column U-joint.
  19. With the aid of an assistant, support the instrument panel and remove the 3 bolts and 1 nut attaching the left side of the instrument panel.
  20. With the aid of an assistant, pull the instrument panel rearward and disconnect the heater controls and air conditioner vacuum line connector, if equipped. Unplug any remaining wiring harnesses.
  21. With the aid of an assistant, carefully remove the instrument panel through the front door.
To install:
  1. With the aid of an assistant, carefully position the instrument panel through the front door.
  2. With the aid of an assistant, position the instrument panel forward and connect the heater controls and air conditioner vacuum line connector, if equipped. Engage any wiring harnesses
  3. With the aid of an assistant to support the instrument panel, install the 3 bolts and 1 nut attaching the left side of the instrument panel.
  4. Move the lower steering column shaft toward the column U-joint and install the the steering column pinch bolt to the lower steering column shaft. Tighten to 30-42 ft. lbs. 41-57 Nm).
  5. Engage the wiring connectors to the main wiring harness at the left cowl side panel.
  6. On vehicles with manual transmission; engage the wiring connector to the clutch interlock switch.
  7. Engage the wiring connector to the brake light switch.
  8. On vehicles with column shift; connect the shift cable to the steering column shift cable bracket.
  9. Install the 3 nuts attaching the parking brake control to the left side cowl panel.
  10. Engage the wiring connector to the parking brake control.
  11. Engage the wiring connectors to the main wiring harness at the right cowl side panel.
  12. Install the screw and washer assembly located at the lower corner on the right side of the instrument panel.
  13. Install the bolt attaching the instrument panel to the panel brace. Some vehicles may have 2 lower braces.
  14. Position the antenna lead-in cable up and snap the wire to the bottom of the instrument panel.
  15. Install the 2 screws attaching the instrument panel steering column opening cover assembly to the underside of the instrument panel.
  16. Install the top of the instrument panel to the cowl with the 4 retaining screws.
  17. Install the right and left side windshield side garnish moldings.
  18. Install the radio as outlined
  19. Install the connectors to the instrument panel rear lamp wiring and the engine control sensor wiring in the engine compartment by engaging the connectors and tightening the retaining bolts.
  20. Connect the negative battery cable and arm the air bag system

Hope helps (remember rated this).

Posted on Jul 14, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

No lights in any dash board cluster


In the fuse panel, check 15A FUSE 4 and 4 A FUSE 10.

Nov 17, 2016 | Ford F-250 Cars & Trucks

1 Answer

I want to remove the seat belt chime in 1995 ford f 250


I was not able to find this car in a 75-mile radius from the ZIP code given. -----------------------------------------------------------------------------
vas 5054a v19

Nov 26, 2012 | 1995 Ford F250

1 Answer

Rapid water leak from 1995 Ford F-250


Remove the motor mount for another freeze plug is behind it

May 15, 2010 | 1995 Ford F250

1 Answer

Got a 250 supper duty looking for elertic brake controler harness.found a bundle of wires by emergency brake but no 4 prong gray plug.but a lot of wiers with no ends.


it under the dash to the right hand side. must remove lower dash panel to acess. and i think its a 6 pin harness your lookin for in the ford.

Feb 24, 2010 | 2007 Ford F-250 Super Duty Lariat

1 Answer

I need to remove the dash from because its got too many cracks. I am going to replace it , but i don't know how to do it. Its a 1978 Ford F-250


pick up a haynes manule there are a couple of great dash covers on the market
have a look at jegs and autozone

Jan 23, 2010 | 1982 Ford F 250

1 Answer

Were is flasher in ford 1995 econoline 250


flasher unit is under dash by your left foot on drivers side

Jan 04, 2010 | Ford E-250 Cars & Trucks

1 Answer

How do i get to my heater core 1995 ford crown vic


Your heater core is located behind the dash. You need to remove the dashboard and your heater core will be located on the passenger side along the firewall. It will look like a small radiator. Get yourself a haynes manual for good step by step instructions and pictures to remove your dash.

Jan 03, 2010 | 1995 Ford Crown Victoria

1 Answer

Removal of dask so I can repair heater unit


you can remove the outer heater box and sneak in the new door its a little tricky but a lot easier than removing the whole dash and box

Dec 07, 2009 | 1995 Ford Explorer

1 Answer

How do you change the serpentine belt on a 1995 f-250 Diesel


e-mail me at berrydalewolf@yahoo.com and i will scan you a copy to put up. berrydalewolf

Oct 27, 2009 | 1995 Ford F250

Not finding what you are looking for?
1995 Ford F250 Logo

2,166 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5471 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...