Question about 2000 Honda CR-V

2 Answers

On a 2000 Honda CRV, how do you reset the service light?

Posted by on

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Use your honda crv key and insert it in the black push button on where you speedometer is and all.

Posted on Aug 09, 2010

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 3,092 Answers

Needs to be done with a scaner to reset light, most repair shop can do this, you could also try autozone, they can do this for free, do not disconnect battery or it could ask you for a radio code, and if you don't have the code, your going to have a hard time getting it.

Posted on Jul 14, 2010

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

  • 79 Answers

SOURCE: honda crv engine light

I would go to your local Honda dealership and tell them the engine light came on. They will hook it up to a special computer and they will be able to tell you why the engine light came on and what's wrong with the car. Not sure what the cost will be to get it checked out. If you don't have the money for that right now.

Posted on Jan 23, 2009

  • 275 Answers

SOURCE: honda crv 2000 computer reset

Ok,
1. ensure ignition off
2 . bridge the 2 pin connector, Put a piece of wire across both terminals
3.switch ignition on
4. SRS lamp should illuminate for 6 seconds
5.disconnect the bridge wire within 4 seconds of the warning lamp extinguishing
6.SRS lamp should illuminate 2 times, Codes erased
7.switch ignition off
8 Wait 10 seconds. switch ignition on and check SRS warning lamp operation.
hope this helps

Posted on Feb 19, 2009

  • 77 Answers

SOURCE: need to put transmission fluid in my crv honda 2000 i would like to know what is the best type of fluid

You should just go to Honda and purchase it from them. You can go up to the parts counter and either give them your year/make/model or your vin and they will give you exactly what fluid(its the same on all A/T honda's) and the correct amount need. They made the car, they know best.

Posted on May 07, 2009

  • 26 Answers

SOURCE: 2003 honda crv. how do i remove light bulb cover

you have to go under the bumper and and look behind then look for the back of the lightbalb connection. if you see that. pull on it carefully. if rusted, spray some wd forty on it but make sure you dont get the wires with the wd forty

Posted on Aug 05, 2009

  • 90 Answers

SOURCE: honda crv Mki 2001 engine management light has

Hi,
Honda mki2001
The engine chipset computer must have sensed the timing belt too tight or not in line or or the timing not set after the new belt put. You will HAVE to go back to rectify this problem.
A word of advise.... dont loose time... go ASAP to avoide costly damage to the bearings...
Regards
Berry

Posted on Jan 31, 2010

Testimonial: "i will get this checked out and will post if problem rectified ? homer"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why my 2000 honda crv doesnot have heat on the winter time?


check the controls that open the heater lines . vacuum loss or control module is faulty.

Sep 10, 2014 | 2000 Honda CR-V

1 Answer

How to reset service A15 on Honda CRV 2007


On most Japanese cars you can reset the service light using the button on the odometer. Try holding down the button until the service light goes out.

Sep 22, 2013 | 1991 Volkswagen Passat

1 Answer

Fuse diagram 2001 honda crv


On this website, you find fuse box diagram and description Honda CR-V (2000 -2001)

Honda CR 2000 2001 fuse box diagram Auto Genius

Oct 14, 2012 | 2001 Honda CR-V

3 Answers

How do you reset a 2005 Honda CRV airbag light?


with a SCANNER.
your mechanic or Honda Dealer will provide this service....
Disconnecting the battery won`t do you any good.
You will have to fix the air-bag problem first before you can erase the airbag light...

Mar 02, 2011 | 2005 Honda CR-V

1 Answer

Maint req light flashes when i turn on my 2005 honda C.R.V. It has been serviced today by independant garage.


They must have forgotten to reset the light. If you take a look in the service manual it should tell you how to reset it. With most hondas you simply hold the trip reset button and turn the ignition on. Continue holding the trip reset button until the light turns off.

Apr 16, 2009 | 2005 Honda CR-V

1 Answer

Honda crv 2000 computer reset


Ok,
1. ensure ignition off
2 . bridge the 2 pin connector, Put a piece of wire across both terminals
3.switch ignition on
4. SRS lamp should illuminate for 6 seconds
5.disconnect the bridge wire within 4 seconds of the warning lamp extinguishing
6.SRS lamp should illuminate 2 times, Codes erased
7.switch ignition off
8 Wait 10 seconds. switch ignition on and check SRS warning lamp operation.
hope this helps

Feb 18, 2009 | 2006 Honda CR-V

Not finding what you are looking for?
2000 Honda CR-V Logo

325 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...