Question about 1999 Pontiac Grand Prix

1 Answer

How to replace the starter? Please provide answer in Spanish

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Pontiac Master
  • 17,970 Answers

1999 Pontiac Grand Prix 3.8L SFI OHV 6cyl

Podrian haber algunos errores de gramatica ya que se uso un traductor para esta descripcion.

Extracción e instalación
3.1L, 3.4L (VIN X) y motores de 3.8L

How to replace the starter - 38e577d.jpg

La figura. motor de arranque típico de montaje del motor 3.1L-muestra

34aa630.jpg

La figura. Desconecte las conexiones eléctricas de arranque. . .



La figura. . . . a continuación, afloje los tornillos de fijación y extraer el motor de arranque del vehículo

1d47bb3.jpg

La figura. La mayoría requiere la eliminación de arranque aflojando los tornillos del volante. . .

141c7f1.jpg

La figura. . . . luego retirar la cubierta plástica del volante

b26944b.jpg

La figura. Una llave de tubo de extensión es a menudo necesaria para conectar con el motor de arranque pernos de retención

144d66c.jpg

La figura. Al retirar el motor de arranque, mantener la cuña delgada chapa (s) ya que pueden ser requeridos en la instalación
How to replace the starter - ab622a4.jpgrel='nofollow' href="http://repairguide.autozone.com/znetrgs/repair_guide_content/en_us/images/0900c152/80/21/7a/ef/medium/0900c15280217aef.gif">ab622a4.jpg

La figura. motor de arranque típicos motores de 3.8L de montaje-se muestra

ADVERTENCIA
Recuerde que el cable positivo de la batería al motor de arranque es eléctrico "calientes" todo el tiempo. Debe abrir el circuito desconectando el cable negativo de la batería antes de reparar el motor de arranque.

continua...

Posted on Jul 14, 2010

  • ZJ Limited
    ZJ Limited Jul 14, 2010




    1. Desconecte el cable
    negativo de la batería.


    2. Levante y con seguridad
    el apoyo del vehículo.


    3. Retire las conexiones
    eléctricas en el motor de arranque,


    4. Quite la cubierta del
    convertidor de par.
    Por lo general, esto es
    solo unos cuantos tornillos y tuercas pequeñas o pequeñas


    5. Retire el motor de
    arranque pernos de montaje.
    Tenga cuidado de que el
    motor de arranque es relativamente pesado.
    No permita que se caiga. Tome nota de cualquier
    cuñas de metal delgado entre el bloque de arranque y el motor.
    Pueden ser necesarios
    durante la instalación.


    Para instalar:



    6. Coloque el motor de
    arranque, incluidas las cuñas encuentra en retirada, al bloque del motor
    e instale los pernos de montaje.
    Apriete los tornillos a
    32 libras / pie.
    (43 Nm).

    7. Instale el convertidor de
    par cubierta y apriete los tornillos de la cubierta del convertidor de
    par a 89 pulgadas por libra.
    (10 Nm).

    8. Coloque los cables en el
    arrancador.
    Apriete el solenoide de
    arranque "BAT" (cable fuerte) la tuerca a 84 pulgadas por libra.
    (9 Nm). Apretar la tuerca del
    solenoide del motor de arranque terminal S a tan sólo 27 pulgadas por
    libra.
    (3 Nm).

    9. Bajar el vehículo.

    10. Conecte el cable negativo
    de la batería.
    Arranque el motor para
    verificar su correcto funcionamiento.




    Espero que esto le sea de ayuda (recuerde valorar este aporte).

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Donde seven cuentas el termostato de Isuzu rodeo 2003 2.2l


spanish on a english only forum. (usa forum it is)
if i answer in spanish , it wont post and spanks me.... spelling errors. or thinks spanish is profanity.. oddly.......

so it's a thermostat question (engine?-)
"where 7 accounts"
i translated this to that. and is no good.
7 what? days?

please post back in english
google translator will work ok.
do so.

Mar 09, 2015 | Isuzu Cars & Trucks

1 Answer

Replace starter cable


Take the ground wire - and positive wire + off. Get a replacement cable, take the nut off the holds the cable to the starter. Install the new cable on the starter, then install the other end to + of the battery. Finally install ground wire - on the battery. Please rate my answer so I am rewarded points for it.

Feb 01, 2012 | Chevrolet C1500 Cars & Trucks

1 Answer

Starter or solenoid


The Ford 7.3L diesel engines require a LOT of power to crank them over. The FIRST thing to check would be the battery and battery cables. If you are absolutely certain that these are in good condition, then you must check for power coming from the starter relay (mounted on the right fender apron) to the starter solenoid (part of the starter assembly)

The "click" you are hearing is either the starter relay or the starter solenoid, or BOTH at the same time. If the starter relay is providing the correct power to the starter solenoid, then the starter assembly must be replaced. If the starter relay is not providing the correct power, then most likely the starter relay is bad.

You just have to check for the proper current at the proper places and the problem will be found.
Please note that your truck is also most likely equipped with 2 batteries. One battery being bad can cause BOTH of them to not work properly. So when you test your batteries, it is best to disconnect them and test each battery on its own merit.

Oct 15, 2011 | 1997 Ford F350 Crew Cab

1 Answer

Car starting problem, but if I connected a wire from the starter to the battery it starts fine. Is there a security system in between the starter and battery that I can disable? Is it the security or...


I believe what you are looking at would be the starter solenoid. For the cost, you may want to replace the starter with the solenoid - depending upon the vehicle.You really should inquire on that.

Best regards
Ck
Please provide feedback

Oct 03, 2011 | 2001 Toyota Avalon

2 Answers

When it doesnt start I turn the ignition on and off serveral times then it starts


That would tell me that I may want
to check out the ignition switch

Do you agree,only a guess

May 28, 2011 | 1990 Toyota 4Runner

3 Answers

I have a 1991 nissan king cab and when i turn the key to on, all electronics in the cab work, fan lights radio ect, then i turn it to start and nothing happens, not a click not turning over nothing....


You could be correct, if the starter solenoid is bad and not making contact it will kill the entire electrical system and also not engage the starter motor. I would replace the solenoid. Please rate this answer, thanks.

Feb 01, 2011 | 1991 Nissan King Cab

3 Answers

Starter clicks but engine does not trun


see can jump start to the starter itself,not the battery.

Jul 25, 2009 | 1992 Oldsmobile Ninety Eight

1 Answer

I own a ford e-250 79. when cold it's start nice


Hello tchuire13: My name is Roger and I will help you. The problem you describe is that of a bad starter. When the bushings wear down the armature will touch the fields inside the starter case. This happens when the starter is warm. Starter will generally work fine cold. After a heat soak the starter acts up. Replacement of the starter should cure your problem. SHould you need further help please just ask. Please rate the answer you received. This is how we know you received the correct answer to your question. Thank You for using Fix Ya. Roger

Jul 08, 2009 | 1983 Ford Econoline

1 Answer

Need to replace starter need info on how to do it.


chb725: If you go to mybunkey solutions and see the heading " "Starter, battery and alternator ok", you will find that I have given instructions for the removal and installation of a starter for a 1995 Nissan Maxima, in great detail.
The instructions include the tools needed, proceedures in a sequence more detailed (which you will not find in any book) and precautions to be taken during the removal and installation of the starter.
I hope this will provide the answer you are looking for. If not, I will await a more detailed request from you.

Apr 20, 2009 | Nissan Maxima Cars & Trucks

Not finding what you are looking for?
1999 Pontiac Grand Prix Logo

652 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8201 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...