Question about 1998 Saturn SL

1 Answer

Just changed the left front caliper and now I can' get any petal and it doesn't want to bleed.

Posted by on

  • bsritchie Jul 14, 2010

    Will look for to see if I can find one of these tools

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Saturn Master
  • 6,826 Answers

There are also pressurized bleeding systems which force brake fluid through the master cylinder to the calipers' bleeding screws and this may help if there is a lot of 'air' in the system.

Hope this helps.

Posted on Jul 14, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to fix1977 corvette stuck front caliper?


replace both calipers and bleed system. remove wheel, unbolt brake flex hose where it mounts to the caliper,clamping hose to keep from losing brake fluid, unbolt caliper from caliper mounting bracket. and remove caliper. re-install in reverse order bleeding front brakes making sure master cylinder doesn`t run out of brake fluid.

Sep 03, 2014 | Cars & Trucks

1 Answer

How to bleed front caliper on 1981 Corvette


Fill master remove bleeder have somebody rapidly pump brake pedal while you hold your finger over the hole. within ten pumps (usually) fluid should come out.By holding your finger over the hole you will feel air pressure let that pass Then do your manual bleed.If still nothing check the rubber line sometime they get messed up inside and fluid will not go through

Aug 22, 2014 | 1981 Chevrolet Corvette

1 Answer

Need help bleeding brakes 2004 ford explorer


To bleed the brakes 1st make sure the fuild level is full ,and you will need a assistant . have your assistant pump the brake petal three to four times then hold presure on petal (pushing down ) then open the bleeder valve on the left rear caliper ,have assistant push petal towards the floor until it stops and then hold it there until you close the bleeder valve ,then repeat process four to five time recheck brake fulid level then repeat same process on right rear caliper next go to right front and end on left front ,keep a eye on the fuild level so that it is not allowed to run out or you will have to start over again ,there is no speical procedure ,any other questions just ask

Dec 29, 2010 | 2004 Ford Explorer

2 Answers

My brakes will not get hard. The pedal goes to the floor. I just changed rear caliper and rotor on the drivers side.


DId you bleed the system after you changed the caliper? If the Master cylinder lost it's fluid while you were changing the caliper, then there is air in the system and you need to bleed the entire system. start with the REAR RIGHT, then the REAR LEFT and then the FRONT RIGHT and last the FRONT LEFT. make sure the master cylinder NEVER runs low on fluid and DO NOT re-use any fluid that you get out of the calipers.

Dec 27, 2010 | 1992 Cadillac Seville

2 Answers

Changed break line but still have no pressure in breaks


to do a complete job. you need to bleed all 4 wheels, starting from Right Rear. Right front. Left Rear. Left Front.

Apr 07, 2009 | 1995 Chevrolet Silverado 2500

1 Answer

Air in front brake lines lexus gx470


If the bleed screws are on the lower side of the calipers, you have put the calipers on the wrong sides. Switch the calipers and rebleed

Mar 27, 2009 | 2003 Lexus GX 470

1 Answer

Brake petal goes to floor


if you cant find any leaks in lines or cylinders or calipers u probaly have a bad booster
see lots come threw my shop like that but also their is a vacum line that runs to the booster and it hooks to a plastic valve that goes in to the booster those get gloged and you loose pedal as well try replacing that before you bye a new boooster

Mar 26, 2009 | 2000 Jeep Grand Cherokee

1 Answer

98 Camry brakes


I would suggest replacing the caliper hoses and following a proper bleeding procedure before replacing the master cylinder

Nov 02, 2008 | 1998 Toyota Camry

Not finding what you are looking for?
1998 Saturn SL Logo

Related Topics:

24 people viewed this question

Ask a Question

Usually answered in minutes!

Top Saturn Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7710 Answers

Are you a Saturn Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...