Question about Cars & Trucks

Open Question

How to replace a knock sensor in a pt cruiser

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

66 chrgr
  • 1011 Answers

SOURCE: where is the crank sensor located on 2005 chrysler pt cruiser?

the crank sensor is located on back right side of engine by were the trans. bolts up.is the no start when could or hot?

Posted on Jan 25, 2009

BCAS1298
  • 3092 Answers

SOURCE: replacing a starter in a PT. Cruiser 2001

Remove battery and battery support you'll be able to undo starter bolt's trough there and slip starter out.

Posted on Dec 08, 2009

Testimonial: "This didn't help, because you had to remove the engine structural collar under the starter to get at the starter bolt. It was more complicated."

  • 615 Answers

SOURCE: '05 PT Cruiser O2 sensor problems.

I had a similar problem with my car. It turned out the O2 sensors were fine and the issue was a leak in the throttle body causing the engine to run lean. If you have an ODB2 scanner you can look at fuel trims, etc and will be able to tell.

Posted on Mar 28, 2010

  • 2309 Answers

SOURCE: 2007 PT Cruiser basic RAD fan battery relay feed replacement

grt one at any parts store, it should be in the fuse or electrical box, look in the owners manual, pull out the the ole and plug in the new

Posted on May 08, 2010

BCAS1298
  • 3092 Answers

SOURCE: how do I replace a 2005 pt cruiser camshaft sensor

Camshaft sensor sit in the end of the cylinder head, drives side, just unscrew both little bolt's from sensor, remove sensor, and install new cam sensor, no reprogramming needs to be done.

Posted on Sep 09, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a PT 2010 & the diagnostic codes are PO340, PO344 and PO325. mechanic is suggesting replacing the cam shaft post sensor & didn't even mention the knock sensor. Am I dealing with 1 or 2 issues


you are dealing with 2 issues
code p 0325 refers to knock sensor (KS) 1 bank 1--circuit malfunction ====causes ---wiring ---poor connection ---KS
code p 0340 refers to camshaft position sensor(CMP) sensor A bank 1--circuit malfunction===causes wiring--- CMP sensor ---ECM
code p 0344 refers to CMP sensor A bank 1 --circuit intermittent===causes --wiring --poor connection---CMP sensor --ECM
check wiring and connections before replacing the CMP as the wiring may be the cause of all the codes

Oct 21, 2016 | 2010 Chrysler PT Cruiser

1 Answer

My 2003 PT Cruiser has a engine light on that said knock sensor was bad I replaced and the car is still doing the same thing


try disconecting battery to reset computer ,if does not change go to auto parts store and have them check computer for codes, this should narrow down problem

Mar 05, 2013 | 2006 Chrysler PT Cruiser

1 Answer

Need to install knock sensor on a 2004 pt cruiser turbo


It is located below intake manifold, in front of your oil dip stick. It will be screwed into the front of the block.

Mar 27, 2011 | 2004 Chrysler PT Cruiser

1 Answer

Where is the knock sensor for a 2003 pt cruiser 4 cyle. standard


look in engine block kindly behind the oil dip stick tube

Mar 30, 2010 | 2003 Chrysler PT Cruiser

1 Answer

I have a 2003 PT cruiser w/ the check engine


It senses when the engine pings and the computer will adjust the timing accordingly. It is located in the block.

Jun 26, 2009 | 2003 Chrysler PT Cruiser

3 Answers

Code 344 camshaft sensor ciurcut intermitint 05 pt cruiser


im having exactly the same problem with a 2004 pt. took it to a dealer they told me ecm, replaced it and still the same problem. i changed out the cam knock sensor and the crank sensor. same thing. if i erase the code it will run perferct for an hour sometimes then same thing, light comes on and wont accelerate, over 2000 rpm. weird. im lost, it makes no sence.

Jun 03, 2009 | 2005 Chrysler PT Cruiser

1 Answer

Knock Sensor location on a 2004 Dodge ram 1500 5.7 hemi


2 knock sensors are used..small black plastic sensor bolted into engine block below each exhaust manifold..be careful not to over torque bolts upon installation

Feb 24, 2009 | 2003 Chrysler PT Cruiser

1 Answer

Where is the knock sensor located


its loacted on the front of the engine block just above the oil pan.. it has a bolt thru the center of it and a single connector

Jan 20, 2009 | 2003 Chrysler PT Cruiser

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

429 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...