Question about 2005 Lincoln LS

1 Answer

Etc fail safe mode codes p2104 2107 2110 2111 2112

Etc fail safe mode appears on dic. had the codes ran and this is what they gave me, codes p2104 2107 2110 2111 2112

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Lincoln Master
  • 6,826 Answers

P2104 Throttle Actuator Control System - Forced Idle
P2107 Throttle Actuator Control Module Processor
P2110 Throttle Actuator Control System - Forced Limited RPM
P2111 Throttle Actuator Control System - Stuck Open
P2112 Throttle Actuator Control System - Stuck Closed

Seems like Throttle Actuator is the problem.

Good luck on this repair.

Posted on Jul 13, 2010

  • mikkisarabia Sep 08, 2010

    I too had the same codes on my 2004 Lincoln LS 3.0. But how could it be the throttle actuator if I had just replaced the entire throttle body before I got the diagnostic from the dealership? Yet they told me I need to replace all 6 ignition coils, when none of the 300 codes even came up. Because its time to renew my tags, I took my car to get smogged even though my check engine light is on. I read on the internet that ignition coil failure does cause emission failure, so I was hopinhg to qualify for the government assistance to fix the coils. Only to find out that I passed emissions, and failed the function light test. In addition to the previous throttle actuator codes, the smog place gave me about 6 new codes. My car is currently at Meineke (obviously the dealership prices are ridiculous), and after originally agreeing with the dealership about the coils, Meineke is now telling me that after driving my car, no codes showed up at all. Therefore, they don't believe it is the coils, and think it may be some bad wiring with the PCM. The symptoms of my car consists of the wrench light turning on while sometimes accelerating, and the car seems to bog out. I basically then have to pull over and re-start my car. After restarting, the car is fine until I accelerate abnormally again. The check engine light always stays on. Can someone please prevent me from not getting inevitably screwed over?

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What causes my 1998 Jaguar XK8 not to start when initially cranked and the Fail Safe message is displayed?


Is the check engine light displayed? If it is, that's where you start, by retrieving the fault code(s). If not, then you could have a security system fault, fuel system breakdown, etc. All codes, regardless of the systems affected, will cause the vehicle computer to immediately default to a failsafe mode, till the problem has been fixed, and this drastically affects driveability, causing no-start issues, idle problems, etc.

Mar 03, 2015 | 1998 Jaguar XK8

1 Answer

Safe mode car radio


To unlock your VW factory radio from "SAFE" mode, you will need to enter the radio code. Typically, the code is written on a radio card included with the documentation for the vehicle when the car is first sold.

If you don't have the code, or have lost it, you can retrieve it by visiting your VW dealer. You will need the car's VIN number and the serial number of the radio (located on the body of the radio).

The procedure to enter the code is as follows:

Press the "MODE" and "SCAN" buttons simultaneously and hold them until "1000" appears on the radio display. Release the buttons as soon as this number appears.

Refer to your Radio Card and use the station preset buttons ("1", "2", "3" and "4") to input the code. Press the "1" button repeatedly to input the first digit, the "2" button to input the second digit, etc.

Press and hold the "MODE" and "SCAN" buttons simultaneously until "SAFE" appears again. Release, and the radio should be unlocked.

Do not enter the wrong code more than three times, or the radio will lock itself. Note the dealer can also enter the code for you (they may charge a small fee).

Oct 17, 2013 | Volkswagen Cars & Trucks

1 Answer

05 mini cooper S went into limp home mode, warrning lights blinking, shut off and re-started. Stopped for a bit then back into limp home ? what might be causing this


Look in the owners manual

There is usually only a couple choices
when you go into Fail Safe

ETC Fail Safe -- for ignition problems,to protect the converter
Overheating Fail Safe
Transmission Limp Mode or Overheat

Just examples
Don't know your vehicle systems

Check for codes as ALWAYS WITH ALL
VEHICLE PROBLEMS first thing you do,
don't need to ask any questions

Check for codes-- then google them

Sep 14, 2013 | 2005 Mini Cooper S

1 Answer

Fail safe mode


ETC Fail Safe or Temp Fail Safe


ETC-- you spray the throttle plate,then
check for really bad COP Ignition Coils

Jun 09, 2011 | 2006 Ford Expedition

2 Answers

Fail safe mode came on what can we do


when a car goes into fail safe or limp mode it is caused by an inportaint sensor the car needs to either run the motor or shift the trans..ikt then runs or operates on the driving info that the ecu has stored to be able to get it home or to a shop..youj will need to have a diagnostics ran on it and have the cars computer read to retrieve the code to idenify the problem and once the problem componet is replaced the car will automaticly return to normal operation

Feb 21, 2011 | 2005 BMW X5

1 Answer

My 1998 beetle is stuck in 3rd gear. the engine and coolant light is on any suggestions?


This just happened to me. I drove the beetle in the snow and slid up to a stop sign. The slide engaged the anti-lock brakes. After that, the car was sluggish starting out and would not shift into 4th gear.
Turns out, the transmission was stuck in 3rd gear. If you can believe it, this is by design! It's a fail safe mode that gets triggered by the wheels spinning out of sync.
According to my mechanic there are wheel speed sensors on each wheel. If the computer senses the wheels moving at different speeds it will drop into fail safe mode. This requires a special scan tool to clear the codes.
Once the codes were cleared, ran like new.

Oct 24, 2010 | 2006 Volkswagen New Beetle

2 Answers

What causes 2004 Lincoln LS with V8 to go into


Over heating causes it to shut down 2 cyl n run on 6 cyl to help cool it down but once that happens the best is to shut it off check the cooling system check for antifreeze make sure its full then take the ground off the battery that's in the trunk beside the spare tire n leave the postive on but take off negative n leave it off for 5 mins then hook it back on it will turn the safe mode off back to normal. That's what I did to my 04 lincoln LS v8 3.9l... hope this helps ya

Mar 06, 2010 | 2004 Lincoln LS

1 Answer

ETC fail safe mode appeared on screen-what is this?


Electronic Timing Control. Has to do with your coil packs/spark plugs. There was a recall on this, check with your dealer for a TSB on the issue. Car running rough?

Oct 01, 2009 | 2003 Lincoln LS

Not finding what you are looking for?
2005 Lincoln LS Logo

3,899 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lincoln Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

fordexpert

Level 3 Expert

5501 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Lincoln Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...