Question about 1997 Ford F350 Crew Cab

1 Answer

Door adjustment for a 96 f350 dropped about 1/2"

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 6,826 Answers

Here's the solution: You might want to park it under a tree and tie a rope to the door to pull it up when loosened.
ADJUSTMENT Fig. 1: Door hinge adjustment door adjustment - 84920001.gif
Fig. 2: Rear door hinge adjustment, F-350 Crew Cab
NOTE: Loosen the hinge-to-door bolts for lateral adjustment only. Loosen the hinge-to-body bolts for both lateral and vertical adjustment.

  1. Determine which hinge bolts are to be loosened and back them out just enough to allow movement.
  2. To move the door safely, use a padded prybar. When the door is in the proper position, tighten the bolts to 19–25 ft. lbs. (25.5–34.5 Nm) and check the door operation. There should be no binding or interference when the door is closed and opened.
  3. Door closing adjustment can also be affected by the position of the lock striker plate. Loosen the striker plate bolts and move the striker plate just enough to permit proper closing and locking of the door.
prev.gif next.gif

Posted on Jul 13, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

96 ford f350 7.5l no start.


map sensor, make vacuum longer, twice as long...

Feb 26, 2014 | 1997 Ford F350 Crew Cab

1 Answer

Adjust hinge on a 96 acord drivers door


Where the door is bolted to the "A"post is the adjustment point,slacken off top and bottom bolts adjust and re-tighten bolts..Simple yea!!!

Jan 06, 2013 | 1994 Honda Accord

1 Answer

1995 f350 powerstroke wont start one other time had to drop shifter and put back to park before it started now it wont start the lights elect windows and glow plug cycles but no clicking noise just nothing


replace the transmission range sensor. Adjust the new sensor by loosening the bolts slightly, turning the key on, putting the truck in reverse, and turning until reverse light come on.

there are 2 possible sensors, depending on which transmission you have.

jturcotte_2379.gif

jturcotte_2380.gif

Oct 06, 2011 | 1995 Ford F350

1 Answer

I have a 96 ford f350 with a 7.3 diesel. The


You may have spun the speedometer cable gear off in the transmission. Try replacing the speedometer cable.

Jul 10, 2010 | 1993 Ford F350

1 Answer

I have a 96 F350 7.3L turbo diesel. The brakes work sometimes but become very hard. The brake light comes on and stays on but goes off within about 5 to 10 minutes. Is this a vaccum pump problem or is it a...


The hard braking sounds like a faulty master cylinder and the light problem if I understand your explanation correctly is a brake light switch problem that may just need an adjustment or if corroded or very dirty may need replaced.

Dec 03, 2009 | 1996 Ford F350 Crew Cab

1 Answer

Is their a down shift or kick down adjustment on a 96 F350 with a 460 engine.


i believe this is done electronicly with the throttle position senser. i would suggest you buy an after market repair manual

Nov 08, 2009 | 1996 Ford F350 Crew Cab

1 Answer

How do you change the glow plugs and relay in a F350 1997


Hello, here is the proceedure. Any questions please ask. Good luck. CAUTION The red-striped wires on the 1994-96 DI Turbo engine carry 115 volts DC. A severe electrical shock may be given. Do not pierce the wires.
  1. Make sure the ignition switch is OFF.
  2. For 1994-96 engines, remove the valve cover.
  3. Disconnect the wire connector from the glow plug.
  4. Using a 10mm deep socket, with enough clearance as to not break or bend the wiring connector, unscrew the glow plug from the manifold.
To install:
  1. Place anti-seize on the threads of the glow plug and screw it into the manifold.
  2. Tighten the glow plug to 12 ft. lbs. (16 Nm).
  3. Plug the wiring connector.
  4. Connect the negative battery cable.
  5. For 1994-96 engines, install the valve cover.
0900c152801cd773.jpgFig. 4: Disconnect the wire, then remove the glow plugs as shown

Jan 23, 2009 | 1995 Ford F350

Not finding what you are looking for?
1997 Ford F350 Crew Cab Logo

1,058 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

77186 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

fordexpert

Level 3 Expert

5575 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...