Question about 1997 Chevrolet Lumina

1 Answer

How to un ininstal the electric window motor on a 1997 lumina

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 17,970 Answers

Window Regulators and Motors - REMOVAL & INSTALLATION

NOTE Some window regulators are retained at least in part, by heavy-duty pull rivets. To remove these rivets, the center mandrel must be pushed through with a small punch, and the rivet(s) drilled out with a 3 / 16 inch drill bit. The factory recommended repair requires the use of the same quality of heavy-duty pull rivet.
Front
CHEVROLET


how to un ininstal the electric window motor on a - fd0e0d8.jpg
Fig. Typical W-Body power window regulator and bolt tightening sequence


293730c.jpg
Fig. Chevrolet models use a cross-arm type window regulator
Coupe and sedan front doors use a cross arm regulator. The following procedures are required for removal and replacement of both power and manual window regulators.

  1. Remove the door trim panel, as outlined in this section.
  2. Remove the plastic sheet water deflector and the energy absorber (foam pad).
  3. Remove the door window. Please see Door Window Glass, Removal and Installation in this section.
  4. Detach the electrical connector, if equipped.
  5. Remove the window regulator bolts and the regulator cam nut.
  6. Drill out and remove the pull rivets.
  7. Remove the window regulator cam bolt.
  8. Remove the window regulator from the vehicle.
CAUTION Do not attempt to service the window regulator motor separately. It is part of the window regulator. The regulator lift arm is under tension from the counterbalance spring and can cause personal injury if the motor is removed from the regulator. The door window regulator cannot be serviced separately. If defective, replace the regulator and motor as an assembly.
To install:
  1. Position the regulator by inserting the bottom through the access opening in the door, then rotate the top of the regulator through the opening while lowering the regulator to clear the top of the access opening. Align the holes in the regulator with holes in the door inner panel.
  2. Install the door window regulator bolts and tighten to 89 inch lbs. (10 Nm).
  3. Install new pull rivets. Install the upper left rivet first, followed by the lower right rivet.
  4. Install the door window regulator cam bolt and cam nut and tighten both to 89 inch lbs. (10 Nm).
  5. Attach the electrical connector, if equipped with power windows.
  6. Install the door window. Please see Door Window Glass, Removal and Installation in this section.
  7. Install the energy absorber (foam pad) and reposition the plastic sheet water deflector.
  8. Install the door trim panel, as outlined in this section.

Hope helps (remember rated this).

Posted on Jul 13, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Tail light schematic 97 chevy lumina


Follow the link for free diagrams of US sold makes http://bbbind.com/free_tsb.html

Dec 01, 2016 | 1997 Chevrolet Lumina

1 Answer

How do i replace left window switch on a 1997 chevrolet lumnia


the actual switch to roll your window up, or is it the window motor? window switch is easy. all you have to do is remove door panel and disconnect the connector from the switch and pop it out of the panel and install the new one. window motor, you have to remove panel and there is a metal frame on inside the door that is sometimes riveted. if that's the case, you may need to rivet it after you pop the rivets. or some make a hole around the motor specifically there to replace the motor. shouldn't be a bad job. all you have to do is get in there and see what you got. not that hard of a job.

Aug 24, 2014 | 1997 Chevrolet Lumina

1 Answer

Diver window wont go up it's electric


I have a 1988 GMC pickup sometimes one window or the other won't go up,it's usually in the switch,probably due to wear,i usually work the switch up and down making sure i have fully depressed it both up and down after awhile it begins to work
the switches need to be replaced ,if this doesn't work, you might check the wiring for lose connections,and finally if all else fails check window motor,and regulator

Sep 25, 2011 | 1997 Chevrolet Lumina

1 Answer

Hi, My friend has a 1997 lumina and did not pass inspection due to her brake light but it has to do with the turning signal. Is there a website that has instructions how to replace or resolve the...


YEP TO FIX BRAKE LIGHTS YOU HAVE TO REPLACE TURN SIGNAL SWITCH BECAUSE MY 98 LUMINA DID THE SAME THING.YOUR BRAKE LIGHT SWITCH AND TURN SIGNAL SWITCH SHARE THE SAME ELECTRICAL CIRCUIT.

Aug 21, 2010 | 1997 Chevrolet Lumina

1 Answer

Driver power window won't roll down or up


Assuming there is no noise like a motor running I'd say the power window motor has gone out and needs replaced.

May 10, 2010 | 1997 Chevrolet Lumina

1 Answer

WHERE IS THE HEATER BLOWER AND FAN SPEED RESISTOR ON A 1997 LUMINA


Should be in the blower motor housing next to blower motor. It is held in the case by small screws and will have an electrical connector going to it.

Nov 03, 2009 | 1997 Chevrolet Lumina

1 Answer

1990 chevy lumina euro 2-door. passenger window


Chevy cheeped out and has been using aluminum rivots to hold the motor in place. to remove the motor remove the rivets.

Apr 25, 2009 | 1990 Chevrolet Lumina

1 Answer

1997 Chevrolet Lumina stalled


I think they are 3 sets.

One on left side of motor
One on right side of motor
One at passanger side door once you open it!

Never hook both cables up to the main power sources car. just the red is needed always ground the ground out to metal on the engine not the battery!

Jan 17, 2009 | 1997 Chevrolet Lumina

Not finding what you are looking for?
1997 Chevrolet Lumina Logo

639 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

78267 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...