Question about 1997 Mercury Grand Marquis

1 Answer

Parts and picture to rebuild a 1997 mercure grand marquis front end. ball joint,tie rod ends ect.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I have the book for the 98 and it says to check the corect wheel bearing adjustment first. or you can do what I did and take it to sears and have then do a free check to tell you what you need.

Posted on Jan 15, 2012

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

SOURCE: 2000 Mercury Sable Ball Joint?

wheel bearing. Lift the car so the wheel is not supported and twist it up nd down,, then right and left. You will feel the play.

Posted on Aug 05, 2008

keemo68
  • 1263 Answers

SOURCE: Tie Rods?? Ball Joints??

at such low milage i seriously doubt that it is the tie rods unless you have a problem with the vehicle wandering down the road. with loose ball joints you would have a alignment problem as well and you would notice a cupping on the tires which you did not mention. I would start by looking at eithere the strut or strut mounts and or the shock and shock mounts for looseness or cracks. also make sure your tires are not over inflated this would cause the shock of the ruts to be amplified to the frame.

Posted on Nov 06, 2008

  • 3 Answers

SOURCE: I want to know how to repair inner and

you have to have a press for the ball joints the tie rods just unscrew once you loosen the adjusting sleeve

Posted on Jun 20, 2009

  • 36 Answers

SOURCE: play in steering wheel replaced upper and lower

raise the truck and have some one rock the steering wheel back and forth while you look for excessive movement at the idler arm - also check is the input shaft on the steering gear box rotating more than the output(pitman arm side) i've seen more steering box failure in the last several years especially true with big tires or boggy road driving, a rebuilt box can be bought at a local parts store- o'reillys, advance, napa etc.

Posted on Nov 23, 2009

reisdos
  • 1297 Answers

SOURCE: need the torque specs for

hope this helps...

4c17033.jpg

2c46aed.jpg

Posted on May 11, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I have a 2003 Grand Marquis with a steering problem, When you turn hard to the right the steering seems to float on them shortly after straightening out makes a hard turn right without turning the ste


Immediately take the vehicle out of service until you can repair it! You may have a dangerously worn or cracked tie rod end or ball joint. Jack up the front end, put blocks or jack stands under the frame (but not the moveable parts of the suspension), and manually try to move the suspension parts. If you detect slop at the moveable connections, that's part of the problem. As part of this, rock the wheels back and forth to check for bad ball joints or control arm bushings.

Another possibility is a bad seal or check valve in the power steering actuator.

Feb 10, 2015 | 2003 Mercury Grand Marquis

1 Answer

How to change front end on 94 gran marquis


Front end is a pretty vague description of what you are trying to do. There are - shocks -lower ball joints -upper ball joints -inner tie rod ends -outer tie rod ends -idler arm -pitman arm -center link -stabilizer links -stabilizer bars It is not likely that all of those need to be replaced at the same time?

Apr 10, 2013 | Cars & Trucks

1 Answer

Need to know the size of the socket needed to remove the front hubs on a dodge ram 3500 1 ton 4 x 4 with cummins engine?


Removing Tie Rod End Attaching Nut Nut is to be removed from tie rod end using the following procedure, hold tie rod end stud with a 11/32 socket while loosening and removing nut with wrench Removing Tie Rod End Attaching Nut
Remove the tie rod end from steering knuckle arm, using Remover, Special Tool MB-991113 Tie Rod End Removal From Steering Knuckle .
Remove the upper ball joint stud from the steering knuckle using Puller, Special Tool, C3894-A Ball Joint Stud .----------------------- The procedure is :-- Do NOT pound on the outside of the hub. First you will need a 5 inch long half inch drive socket extension. Start the 4 hub bolts about half way, then witha helper hold the extension between one of the 4 bolts and the axle housing then have the helper turn the steering wheel to push on the bolt and hub. If it is really rusted in you might have to start the truck to get more pressure on it while turning. Thanks. Keep updated for any more query. You can rate this solution and show your appreciation.

Jul 11, 2010 | 1997 Pontiac Grand Am

2 Answers

My 2001 Mercury Marquis has a sqeeking sound coming from front end, however there is no grease fittings to grease to reduce noise


That sound is a sign of rusted parts. You need to get the front end checked and may as well get an alignment. The manufactuers have reduced the number of grease fittings for years.

All the car makers, not just Mercury claim the parts are lubed for life. The parts would last longer if they could get fresh grease, but most people blow out the rubber boots by overfilling them anyway.

If the alignment shop doesn't find a problem with your car about all you can do is use a light oil or spray Lithium grease into the squeeking part.

Jan 18, 2010 | 2001 Mercury Grand Marquis

1 Answer

How do you change outer tierod ends on a 1996 dodge grand caravan


jack vehicle up in front and make sure its secure. remove front wheels. tie rod is bolted thru steering knuckle. remove the cotter pin from tie rod end. remove the nut from tie rod end. use a small ball joint splitter and small sledge to release tie rod end from knuckle. if you dot have splitter a good hard hit with small sledge on steering knuckle where tie rod attaches will usually release it. b careful not to bend backing plate. loosen the lock nut on tie rod and spin old end off. try to install new end as close as possible to same position as old end. you will need a front alignment after replacement.

Oct 03, 2009 | 1996 Dodge Caravan

2 Answers

95 ef ford sedan suspension problem


What was said about the wear of the front end part when the alignment was given? I could be wrong but, I would say, Not likely for the tie rod ends and definately not the shocks for knocking sounds.. It sounds more like bad ball joints poping, although the idler arm and tye rod ends could be worn also .

Dec 09, 2008 | 1983 Ford Fairmont

1 Answer

1995 Mercury Grand Marquis Suspension


JacDempsey, how about shocks/struts? If they are bad, that could be what u need to cruise the highway nice and smooth the way a Grand Marquis should.

Dec 08, 2008 | 1997 Mercury Grand Marquis

1 Answer

I can feel every crack I roll over 1995 Mercury Grand Marquis.


i see you have replaced everything on front end but one thing, the shocks,a good set of gas filled shocks will give you a better ride..

Dec 08, 2008 | 1997 Mercury Grand Marquis

Not finding what you are looking for?
1997 Mercury Grand Marquis Logo

Related Topics:

163 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

fordexpert

Level 3 Expert

5495 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...