Question about 2004 Pontiac Grand Prix

1 Answer

What is 2004 grand prix gt 3.8 engine head torque table

Whaat is 2004 grand prix gt 3.8 engine head torque specs table

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Champion:

    An expert who has answered 200 questions.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 200 Answers

Go to autozone.com create a free account put in you cars model year etc... then look at the free manual for replacing head gasket it will have a bolt tightening sequence diagram. also they usually have to be taken off in a paticular sequemnce to avoid warping the head. If aluminum heads they usually recommend new head bolt set and having the head shaved (Leveled)

Posted on Jul 13, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Cylinderhead torque settings


I'm not sure what engine you have in your 95 grand am SO I will give you both the 4cyl and 6cyl Specs. Also you didn't ask for the torque sequence. I will include that as well for both. 2.3 DOHC Quad 4cyl: Torque sequence---> front ' 7 3 1 5 9 ' of engine ' 8 6 2 4 10 ' Step 1: torque bolts 1 thru 6 (26 Ft/Lbs & 90 degree turn) Step 2: torque bolts 7 & 8 (15 Ft/Lbs & 90 degree turn) Step 3: torque bolts 9 & 10 (22 Ft/Lbs & 90 degree turn) Recheck final torque in sequence *** CAUTION *** This engine uses "Torque To Yield" (TTY) head bolts that means they permanently stretch during the initial installation. New head bolts must be used when cylinder head is replaced or re-installed in order to obtain proper torque. 3.1 liter V6 Torque sequence--> ' 6 2 3 7 ' ' 5 1 4 8 ' Step 1: torque bolts in sequence to 33 Ft/Lbs Step 2: turn an additional 90 degrees Recheck final torque in sequence *** CAUTION *** This particular engine uses "Torque To Yield" head bolts(TTY) (that means the bolts permanently stretch during the initial installation.) You MUST use NEW head bolts when replacing or reinstalling the cylinder head in order to obtain the proper torque.

Aug 22, 2014 | 1995 Pontiac Grand Am

1 Answer

Wheel bearing torque spec for a 2006 Pontiac grand prix gt on the front wheel bearing hub assemnbly


It shouldnt have torque spec more of press preference to press the bearing in
the bolt should be put on with codder pin to follow

May 17, 2014 | Cars & Trucks

1 Answer

Where is the knock sensor


There are two of them, they are screwed into the engine blocks cooling water jacket (where the drain plugs would have gone for the block without sensors) below the spark plugs and cylinder heads on the front and rear of the engine. See picture below. One note knock sensors seldom fail, also if you do replace it it must be carefully torqued to the proper spec (12 foot lbs I think) or it will not work correctly and that can trigger a fault code once again.

emissionwiz_231.jpg

Sep 21, 2011 | 2004 Pontiac Grand Prix

1 Answer

1999 grand am gt 3.4 head torque


requires new head bolts. also requires thread sealant to be applied to bolts because they go into coolant passages. The torque spec is 60 n.m (44 lb ft) and then and additional 95 degrees. It suggests using a torque angle meter however its just slightly more than one-quarter turn the sequence is as follows. 5 3 2 8
7 1 4 6

May 25, 2011 | 1999 Pontiac Grand Am GT

1 Answer

Front spindle nut torque spec?


Hello Gadd.
The Grand prix axle nut torque is 118 ft lbs.
It is the same torque value for the three different engines that came on the Grand Prix that model year.
There you are, thank you for using FixYa.

KL

Nov 13, 2010 | 1999 Pontiac Grand Prix

1 Answer

Head bolt torque specs


i'm guessing this is a V6 3400 since the headline is a 2000 Grand Am GT
44 LB FT plus 95 degrees

Apr 05, 2010 | 2000 Pontiac Grand Am GT

4 Answers

Need the head bolt torque specs for a 1999 grand am - i am trying to replace the heads on 1999 grand am with 3.4 engine


Fig. Cylinder head bolt tightening sequence-3.1L engines & 2001-04 3.4L engines

7245611.jpg


Fig. Cylinder head bolt tightening sequence-2005 3.4L engines

5579e52.jpg

Hope this help (remember rated and comment this).

Mar 30, 2010 | 1999 Pontiac Grand Am GT

1 Answer

Head bolt torque specs for 1992 Pontiac 3.1 ltr


the last time i did the same job the gasket kit had the specs inside the box. the parts store should have a book/reference manual

Dec 09, 2008 | 1992 Pontiac Grand Prix

Not finding what you are looking for?
2004 Pontiac Grand Prix Logo

1,263 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8180 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...