Question about Land Rover Range Rover

1 Answer

The transfer case .I bougth a transfer case motor and still lock on low and shift the gears fast on low whats the problem it's a96 4.6

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Land Rover Master
  • 11,800 Answers

I really don't understand your question. The transfer case doesn't have any motor attached to it, it's purely mechanical so if you have a problem with it then it must be a problem in the linkage - the shifting rod isn't adjusted properly so it doesn't go full course, so it can't shift to High.
The automatic gearbox is completely separate from the transfer case and if you have a problem with its shifting - too fast - then the problem is in the pressure regulator from the oil circuit of the gearbox: the pressure is too high, the relief valve is stuck shut. That can be fixed with the gearbox attached to the car but it would be better to completely dismantle it, the high pressure has done more damage that will become visible in the future.

Posted on Jul 13, 2010

  • a_aizu Jul 13, 2010

    transfer case shifth motor thats want is call

  • Azrael SRL Jul 13, 2010

    So you have an Range Rover 4.6 HSE auto with a Borg Warner transfer case that is locked on low and the new motor hasn't helped .   

    This is caused by a bunch of causes; the most common one is a faulty sensor inside the transfer box - remove the motor and pull the lever to High by hand, this is usually enough to reset it. But there could be other causes: 
     - the interlock solenoid that was added to prevent the transfer case being moved out of either High or Low range unless the main gearbox is in neutral and the ignition is switched on is faulty and must be replaced.Or it's not powered because the fuse has burned.
     -  the transfer case ECU is faulty and has stopped taking commands - the only remedy is to replace it.
     - the Borg Warner  the transfer case is basically just another automatic gearbox and as such it has failed - it must be checked by a specialist.

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I can here the tranfercase locking in but its not turning front tires at all ?


Your vehicle had option of two different 4x4 systems ,
New Venture Gear 263 Selectable Two Speed Transfer Case
The NVG 263 transfer case features a three button shift control switch located on the instrument panel. When the vehicle has the ignition key in the RUN position, the transfer case shift control module starts monitoring the transfer case shift control switch to determine if the driver desires a new mode/gear position. At a single press of the transfer case shift control switch, the lamp of the new desired position will begin flashing to inform the driver that the transfer case shift control module has received the request for a new mode/gear position. The lamp will continue to flash until all shifting criteria has been met and the new mode/gear position has been reached (or has been engaged). Once the new mode/gear position is fully active, the switch indicator lamp for the new position will remain ON constantly.
The NVG 263 transfer case provides the driver with 3 manual mode/gear positions:
• 2HI - 2 Wheel Drive high range
• 4HI - 4 Wheel Drive high range
• 4LO - 4 Wheel Drive low range
OR
The NVG 236/246 transfer case features a 4 button shift control switch located on the instrument panel. When the vehicle has the ignition key in the RUN position, the transfer case shift control module starts monitoring the transfer case shift control switch to determine if the driver desires a new mode/gear position. At a single press of the transfer case shift control switch, the lamp of the new desired position will begin flashing to inform the driver that the transfer case shift control module has received the request for a new mode/gear position. The lamp will continue to flash until all shifting criteria has been met and the new mode/gear position has been reached, or has been engaged. Once the new mode/gear position is fully active, the switch indicator lamp for the new position will remain ON constantly.
If there are problems with electronic part of the systems the shift control switch light will flash warning of a problem , If no lights you have a mechanical problem in the transfer case itself .
The front axle control circuit consists of an electric motor actuator which engages and disengages the front axle. The front axle actuator motor consists of a Permanent Magnetic (PM) motor, a worm gear controlled plunger, a front axle switch and an electronic control circuit all within the actuator assembly.
The front axle actuator has four circuits connected to it, a front axle feed circuit, front axle ground circuit, front axle control circuit and a front axle switch circuit.
Whenever a shift to AUTO 4WD, 4HI, or 4LO is requested, the transfer case shift control module engages the front axle by grounding the front axle control circuit through a current limiting driver. Test Description
The numbers below refer to the step numbers on the diagnostic table.
Tests the electrical function of the front axle actuator. Helps determine between mechanical and electrical malfunctions.
Tests for proper power and ground at the front axle actuator.
Tests the operation of the front axle control circuit.
Helps determine if the transfer case shift control module is able to monitor the front axle switch.
Tests the front axle switch circuit for an open or high resistance.
Measures the voltage between the front axle feed circuit and ground.
Tests the front axle control circuit for an open or high resistance.
Inspects the front axle for a mechanical malfunction.
Tests for open in the front axle feed circuit.

Feb 14, 2016 | 2001 GMC Yukon

1 Answer

4 wheel drive won't engage


Which do you have ?
Transfer Case - NVG 236 (Two Speed Automatic)
Transfer Case - NVG 233-NP1 (Two Speed Selectable)
The NV236 transfer case is an automatic transfer case with three drive ranges. Shifting from rear wheel drive to four wheel drive is done automatically when the transfer case shift control module receives wheel rotating slip information from the speed sensors. The transfer case shift control module then engages the transfer case motor/encoder to position the transfer case from rear to four wheel drive. When the transfer case shift control module receives information that the wheel rotation is the same on both axles, the transfer case shift control module sends position information to the motor/encoder to put the transfer case back into rear wheel drive. The three drive ranges are 2HI, 4HI, and 4LO. The 2HI position is for normal driving with the rear wheels pushing the vehicle. The 4HI, position is for driving through sand, snow, mud, gravel, or heavy rain at normal or slightly below normal speeds. The 4HI engages the front axle to allow for four wheel drive. The front axle is pulling the vehicle, and the rear axle is pushing the vehicle. The 4LO range is used for off road driving, heavy snow, deep mud, or shallow fording. The 4LO is similar to the 4HI except that the gearing in the transfer case is set for low speed and high torque. The NV236 is manufactured at Syracuse New York by New Venture Gear a division of New Process Gear for General Motors.
Is the switch light on or flashing ? If you have automatic 4x4 there are several DTC'S that can set >
DTC B2725 ATC Mode Switch Circuit Malfunction DTC C0300 Rear Speed Sensor Malfunction DTC C0305 Front Speed Sensor Malfunction DTC C0308 Motor A/B Circuit Low DTC C0309 Motor A/B Circuit High DTC C0310 Motor A/B Circuit Open DTC C0315 Motor Ground Circuit Open DTC C0323 T-Case Lock Circuit Low DTC C0324 T-Case Lock Circuit High DTC C0327 Encoder Circuit Malfunction DTC C0362 4LO Discrete Output Circuit High DTC C0367 Front Axle Control Circuit High DTC C0374 General System Malfunction DTC C0376 Front/Rear Shaft Speed Mismatch DTC C0387 Unable to Perform Shift DTC C0550 ECU Malfunction DTC C0611 VIN Information Error

Dec 01, 2015 | 2000 Chevrolet S-10

1 Answer

How do i replace shift motor in 2005 durango


I doubt if the encoder motor is causing the transfer case to stay in low 4WD. It is more likely a problem inside the transfer case.

Jun 04, 2013 | Cars & Trucks

1 Answer

Where is the transfer case shift motor located on 2004 dodge dakota


The transmission control module and the transfer case control module are separate parts. The transmission control module is mounted under the hood and controls only transmission functions. The transfer case control module controls only the transfer case, and is located inside the truck. If you remove the trim panel under the steering column you will find the transfer case control module mounted just to the right of the opening.


The shift motor is located just behind the axle tube to prevent damage.
There is a shift motor on the right front axle that is vacuum operated.
The shift motor (1) is an electromechanical device consisting of a DC permanent magnet motor, a motor brake, a gear train and an analog position sensor. The shift motors' overall function is to move and lock a gear that moves the mode fork found in the transfer case. This allows the transfer case to be shifted electrically to multiple operating positions (4LOCK and AWD). The operating current of the shift motor under
stall conditions is 30 amps maximum at 72° F with 13.5 volts, at the motor leads.
OPERATION
Shifting in the transfer case occurs when the shift motor brake is released and a Pulse Width Modulated (PWM) voltage is supplied to the shift motor by the Front Control Module (FCM). A linear analog position sensor located inside the shift motor, provides the FCM with the motors' angular, rotational position. With this information, the FCM
continuously knows the motors' position, and therefore allows it to accurately control the motors' operation, including voltage polarity which is used to control motor direction.

REMOVAL :---Note: New shift motor assemblies are shipped in the AWD position. If a new shift motor assembly must be installed, it will be necessary to shift the transfer case to the AWD position prior to motor installation.
Raise the vehicle on a suitable hoist.Remove the front propeller shaft. Disengage the wiring connectors from the shift motor and mode sensor.Remove the front output shaft companion flange from the transfer case.Remove the bolts (Remove the Shift Motor and Mode Sensor Assembly Bolts) holding the shift motor and mode sensor assembly onto the transfer case.Separate the shift motor and mode sensor assembly from the transfer case. See fig below:-- helpmech_19.gif
1 - TRANSFER CASE.2 - SHIFT MOTOR AND MODE SENSOR ASSEMBLY.3 - BOLT.-- This should help.Thanks.Helpmech.

Feb 26, 2011 | 2004 Dodge Dakota

1 Answer

My 1999 suburban also stuck in 4 wheel. when i push the button to go into 2 hi it flashes the acuator pulls in then goes back into 4 hi. it wont stay in 2 wheel drive. i have replaces the control on the...


Did you ever think of having it diagnosed by a qualified repair shop ? Thier are aspects associated with this system you have no clue about. That's the first thing every one goes for , changing the switch . It flashes because codes are stored .
DTC B0768 Service Indicator Circuit High
DTC B2725 ATC Mode Switch Circuit Malfunction
DTC C0300 Rear Speed Sensor Malfunction
DTC C0305 Front Speed Sensor Malfunction
DTC C0308 Motor A/B Circuit Low
DTC C0309 Motor A/B Circuit High
DTC C0310 Motor A/B Circuit Open
DTC C0315 Motor Ground Circuit Open
DTC C0323 T-Case Lock Circuit Low
DTC C0324 T-Case Lock Circuit High
DTC C0327 Encoder Circuit Malfunction
DTC C0357 Park Switch Circuit High
DTC C0362 4LO Discrete Output Circuit High
DTC C0367 Front Axle Control Circuit High
DTC C0374 General System Malfunction
DTC C0376 Front/Rear Shaft Speed Mismatch
DTC C0387 Unable to Perform Shift
DTC C0550 ECU Malfunction
DTC C0611 VIN Information Error
You need a professional scan tool to check for these codes an too view data parameters .
Transfer Case Shift Control Module
The transfer case shift control module uses the VIN information for calculations that are required for the different calibrations used based on axle ratio, transmission, tire size, and engine. The system does not know which calibration to use without this information.
The direct battery supply line (CKT 1640) provides the power to the module and motor circuitry.
Transfer Case Encoder Motor
The transfer case encoder motor consists of a permanent magnet (PM) DC motor and gear reduction assembly. It is located on the left hand side (drivers side) of the transfer case. When activated it turns the sector shaft of the transfer case (clockwise or counter clockwise) to shift the transfer case. The encoder motor is controlled with a pulse width modulated (PWM) circuit within the transfer case shift control module. This circuit consists of a driver on both the Motor A and Motor B circuits. The encoder motor is bi-directional to allow the motor to shift the transfer case from 2HI or 4HI to neutral and 4LO positions.
Transfer Case Encoder
Your best bet ,take it to a qualified repair shop .

Jul 18, 2017 | 1999 Chevrolet Suburban

1 Answer

99 Chevy Silverado 4x4 not working No light on 4x4 Selector Panel


Your brake an CV joint issue can't an won't cause your 4X4 problem . The 4x4 system has a control module which supply's B+ voltage to the switch . Checking for codes in the 4X4 control module should have been the first step . Your best bet , take it to a qualified repair shop . You don't have the knowledge or test equipment to fix this.
SERVICE indicator (4WD/AWD) Lamp
The SERVICE indicator (4WD/AWD) lamp is an integral part of the cluster and cannot be serviced separately. This lamp is used to inform the driver of the vehicle of malfunctions within the automatic transfer case (ATC) system. The SERVICE indicator (4WD/AWD) lamp is controlled by the transfer case shift control module via CKT 1567.

Transfer Case Shift Control Module
The transfer case shift control module uses the VIN information for calculations that are required for the different calibrations used based on axle ratio, transmission, tire size, and engine. The system does not know which calibration to use without this information.
The direct battery supply line (CKT 1640) provides the power to the module and motor circuitry.
Transfer Case Encoder Motor
The transfer case encoder motor consists of a permanent magnet (PM) DC motor and gear reduction assembly. It is located on the left hand side (drivers side) of the transfer case. When activated it turns the sector shaft of the transfer case (clockwise or counter clockwise) to shift the transfer case. The encoder motor is controlled with a pulse width modulated (PWM) circuit within the transfer case shift control module. This circuit consists of a driver on both the Motor A and Motor B circuits. The encoder motor is bi-directional to allow the motor to shift the transfer case from 2HI or 4HI to NEUTRAL and 4LO positions.
Do you know what DTC'S are ?
DTC B2725 ATC Mode Switch Circuit Malfunction
DTC C0300 Rear Speed Sensor Malfunction
DTC C0305 Front Speed Sensor Malfunction
DTC C0308 Motor A/B Circuit Low
DTC C0309 Motor A/B Circuit High
DTC C0310 Motor A/B Circuit Open
DTC C0315 Motor Ground Circuit Open
DTC C0323 T-Case Lock Circuit Low
DTC C0324 T-Case Lock Circuit High
DTC C0327 Encoder Circuit Malfunction
DTC C0367 Front Axle Control Circuit High
DTC C0374 General System Malfunction
DTC C0376 Front/Rear Shaft Speed Mismatch
DTC C0387 Unable to Perform Shift
DTC C0550 ECU Malfunction
DTC C0611 VIN Information Error

Aug 27, 2017 | 1999 Chevrolet Silverado 1500

2 Answers

My 4x4 is stuck in four wheel low it is shift on the fly and i have already replaced the transfer case motor


Ok here is a long shot but sometimes it will work. Put the 4wd position switch to 4wd Lo, put your transmission in reverse and back up for about 50 yards, stop and put your transmission in neutral, then shift the 4wd to 4wd hi, wait a few seconds and shift the 4wd to 2wd hi, Sometimes the t-case will get stuck and this is how you reset the computer. I have known people that really got their t-cases messed up because they thought that shift on the go meant that they could shift the t-case into 4wd LO while moving but shift on the go is only for 4wd hi the gears will not mesh up fast enough for 4wd LO because the ratio is 1 to 1 . I hope this helps you.

Feb 08, 2010 | 1990 Ford Bronco

1 Answer

I have a 1995 Silverado 4x4. The 4WD will not engage. Someone told me it may be the actuator for the transfer case. When I try to shift into 4hi, nothing happens. When I try to shift into 4lo, it grinds...


I HAD A BLAZER WITH THE SAME SYMPTOMS REPLACED THE TRANSFER CASE MOTOR AND SOLVED PROBLEM. TRANSFER CASE MOTOR SHIFTS FROM HIGH TO LOW GEAR IN THE TRANSFER CASE AND TELLS THE FRONT ACTUATORS TO INGAGE FRONT HUBS . MOTOR WON'T MOVE TO 4 HIGH AND GRINDS WHEN TRYING TO MOVE TO 4 LOW, TRANSFER CASE MOTOR FAILING . CHECK VACUUM LINES AND ACTUATORS ON FRONT DIFF THEY FAIL, CAN CHANGE TO CABLE ENGAGEMENT INSTEAD OF FAILURE PRONE VACUUM ACTUATORS.

Jan 23, 2010 | 1999 Chevrolet Silverado 1500

1 Answer

1996 ford explorer 4wheel drive will not engage into the hubs need to know how it works


make sure your 4WD switch is working.and fuse is okay.because your 4WD is control by 4 electric shift motors in which drive a rotary cam which moves the mode fork and range fork inside the transfer case to select between 2WD HIGH A4WD - 4WD HIGH AND 4WD LOW RANGE.a shift motor sensing plate on the shift motor monitors the range in which the transfer case is operating a transmission range sensor monitors the gear position of the transmission.which must be in neutral to shift into low.a pair of solenoids one for 2WD one for 4WD.mounted on the upper right firewall route vacuum to the vacuum motor which engages and disengages the center axle disconnect collar in the front axle assembly.a 4 x 4 shift motor relay module contains two GEM controlled relays which shift the transfer case shift motor between 2WD and 4WD modes.a solid state clutch relay activates the A4WDclutch inside the transfer case.

Dec 13, 2009 | 1996 Ford Explorer

1 Answer

Denali slips in and out of 4x4


How may buttons for the 4X4 two , three , or four ? Do the lights flash ? Any messages - service four wheel drive system ? Which transfer case does it have ?

Transfer Case - NVG 246-NP8 (Two Speed Automatic)
The transfer case shift control module uses the VIN information for calculations that are required for the different calibrations used based on axle ratio, transmission, tire size, and engine. The system does not know which calibration to use without this information.
Transfer Case Encoder Motor
The transfer case encoder motor consists of a permanent magnet (PM) DC motor and gear reduction assembly. It is located on the left hand side (drivers side) of the transfer case. When activated it turns the sector shaft of the transfer case (clockwise or counter clockwise) to shift the transfer case. The encoder motor is controlled with a pulse width modulated (PWM) circuit within the transfer case shift control module. This circuit consists of a driver on both the Motor Feed A and Motor Feed B circuits. The encoder motor is bi-directional to allow the motor to shift the transfer case from 2HI or 4HI to NEUTRAL and 4LO positions.
Transfer Case Encoder
The encoder is mounted to the transfer case encoder motor assembly and is replaced as an assembly. The encoder converts the sector shaft position (representing a mode or range) into electrical signals inputs to the transfer case shift control module. The module can detect what position the transfer case is in by monitoring the 4 encoder channels (P, A, B, and C). These inputs translates into AUTO 4WD, 2H, 4H, NEUTRAL, and 4L or in transition between gears.
Transfer Case Motor Lock
The transfer case motor lock is used to provide a 2H, 4H, and 4L lock-up feature. When the lock circuit is energized, the transfer case encoder motor is allowed to turn. When the transfer case is placed 2H, 4H, or 4L the motor lock circuit has no power provided to it and the lock is applied. This assures that the transfer case remains in the current gear position. When AUTO 4WD is selected the motor lock remains applied until an adaptive mode (torque is applied to the front propshaft) is required. During an adaptive mode the motor lock circuit is energized and the motor lock is released, enabling the encoder motor to turn and apply torque to the front propshaft.


SERVICE indicator (4WD/AWD) Lamp
The SERVICE indicator (4WD/AWD) lamp is an integral part of the cluster and cannot be serviced separately. This lamp is used to inform the driver of the vehicle of malfunctions within the automatic transfer case (ATC) system. The SERVICE indicator (4WD/AWD) lamp is controlled by the transfer case shift control module via a Class 2 message or by a Sevice Indicator Control Circuit.

The first thing to do before assuming it's a loose wire would be to have it checked for codes , auto zone , advance etc... can not check this codes .
DTC B0768 Service Indicator Circuit High
DTC B2725 ATC Mode Switch Circuit Malfunction
DTC C0300 Rear Speed Sensor Malfunction
DTC C0305 Front Speed Sensor Malfunction
DTC C0308 Motor A/B Circuit Low
DTC C0309 Motor A/B Circuit High
DTC C0310 Motor A/B Circuit Open
DTC C0315 Motor Ground Circuit Open
DTC C0323 T-Case Lock Circuit Low
DTC C0324 T-Case Lock Circuit High
DTC C0327 Encoder Circuit Malfunction
DTC C0357 Park Switch Circuit High
DTC C0362 4LO Discrete Output Circuit High
DTC C0367 Front Axle Control Circuit High
DTC C0374 General System Malfunction
DTC C0376 Front/Rear Shaft Speed Mismatch
DTC C0387 Unable to Perform Shift
DTC C0550 ECU Malfunction
DTC C0611 VIN Information Error

If you know nothing about this , your best bet would be to take it to a qualified repair shop .

Apr 29, 2017 | 2000 GMC Denali

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

43 people viewed this question

Ask a Question

Usually answered in minutes!

Top Land Rover Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

yadayada
yadayada

Level 3 Expert

76846 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8560 Answers

Are you a Land Rover Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...