Question about 2001 Ford Mustang

1 Answer

Have power to starter continously, have replaced starter, and ignition

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 39 Answers

Sounds like ur ignition barrell wiring switch (inside the car where u put the key in, theres a wiring block on the other side behind the cowelling). dont know much about mustangs to be fair, if theres a relay relating to the starter/ignition it may be worth checking out. hope this helps

Posted on Jul 13, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Lots of power, dash lights up but no ignition power to starter, relay changed, neutral start switch changed, fuses good.


Well, looking at the schematic, there is the IGN A (Fuse 6) in the under-hood fuse block feeding power to both the ignition switch and to the NO contact of the starter relay. Turning the ignition switch to the START position sends this voltage thru the CRANK (Fuse 8) in the instrument panel fuse block and thru the PARK/NEUTRAL position switch, thru the starter relay coil to ground. This should activate the Starter relay and pass voltage to the starter solenoid to ground, activating it. One the starter solenoid activates, batter power is sent to the starter motor, activating it. If, as you say, the fuses are good, the starter relay was replaced and is good, and the Park/Neutral position switch was replaced and is good, then then only items left are the ignition switch itself, the starter solenoid/motor, or the wiring of the circuit.

Mar 12, 2015 | 2000 GMC Yukon XL

2 Answers

My mitsubishi diamnte starter will not shut off


the start relay is sticking or the selenoid on the starter is stuk

Nov 28, 2013 | 1997 Mitsubishi Diamante

2 Answers

Replaced starter and ignition relays under hood on my 99 chevy silverado and to wont do anything no security light no nothing is on everything good on all connections replaced wiring harness...


Is power getting to the ignition switch? Do the warning lights and gauges come on when key is turned to on? That would verify power in and power out at the switch. Then you would need to check the start circuit. A single start wire comes out of the switch, the signal travels through the neutral safety switch and a starter relay and then to the starter solenoid mounted on the starter. Solenoid closes contacts so battery power can operate the starter. If new starter doesn't work, power has been lost between the ignition switch and the starter.
If no power to the ignition switch check maxi fuses, all fuses in fact, and possibly a fusible link from the battery that may be the feed for the switch.

Sep 22, 2013 | 1999 Chevrolet Silverado 1500

1 Answer

Power to starter wire with ignition off


main wire supposed to have power. ignition feeds the solenoid engage wire when ignition is turned on

Jan 17, 2013 | 2004 GMC Envoy

2 Answers

2000 saturn LS1...ignition seems to be locked up. Battery functions, as well as the fuel pump, ignition coil, replaced the starter and crank sensor, and timing gears chain and water pump were all replaced...


Check power to starter motor and solenoid. If no power present on engine crank, then check ignition barrel, key and main fuses.If power present on cranking, but starter motor does not energize, then check starter connections and replace starter motor and solenoid if necessary.
Double check starter motor operation with starter removed from the engine. If it works, then check engine condition as this may be seized.

Nov 03, 2012 | Cars & Trucks

1 Answer

Will not start up or crank over


check for a starter motor or solenoid failure. Also check for a ground wire,for no good contact. also is possible the ignition switch for not sending a message for crank start.Also check for any fuse or relay.

Sep 15, 2012 | 1986 Jaguar XJ6

1 Answer

When I replaced ignition switch in a 2000 buick centery I stll cannot get power to starter and power windows ,gas guage and radio don't work


Sounds like the Ignition switch wasn't the problem, check your fuse links at starter, they are soft fuseable wire that will burn if shorted or even when they get old over time they will go bad. they are the smaller like #10-12 ga. wire , should be at least 1 maybe 2 of them at harness connection to starter.

Aug 30, 2012 | Buick Century Cars & Trucks

3 Answers

Starting difficulty. When I turn the ignition


Check your battery terminals and the hot lead on the starter make sure they are clean and tight. If they are you are most likely will need a starter.

Feb 14, 2010 | 1991 Toyota Pickup

2 Answers

1996 ignition switch-what wires to check power on


ignition switch may be worn or a loose exciter wire [to starter] thats the small terminal on starter motor you can bridge it to the posative [power] on the starter it should start!
if it does start just work back from there to ignition look for broken or loosse connection
if that all is ok it will need ignition switch

Jul 18, 2009 | 1996 Chevrolet Blazer

1 Answer

WONT START


Thai is either ignition cylinder or starter coil, or a problem with starter motor/wirings to starter motor.

The starter motor must be energized directly (in neutral, and possibly using a remote switch) to check that is working.

If the starter motor is fine, check that there is power coming to starter motor when you ignite.
If there is no power, test power at ignition and eventually replace ignition.

Feb 18, 2009 | 1998 Ford Escort

Not finding what you are looking for?
2001 Ford Mustang Logo

Related Topics:

93 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5470 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...