Question about 2000 Chevrolet Silverado 1500

1 Answer

I have a 2000 silverado with the 5.3 engine and the small belt broke not the big serpetine belt just the small belt is it ok to drive it.

Posted by Anonymous on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,608 Answers

Yes you can still drive it.You just will not have any air conditioning.The small belt runs the a/c compressor.Hope this helps.Good luck.

Posted on Jul 13, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2001 eclipse serpetine belt broke put new ones on now car turns over but won't start.


2001 GT Eclipse Spyder..cranked this morning, both drive belts broke, harmonic balancer came apart..replaced balancer, belts, now it won't fire. I did find a piece of one of the drive belts intertwined in the timing belt. Thing is absolutely not getting any fire.

Sep 23, 2015 | Cars & Trucks

1 Answer

I need a digram so i can install a serpetine belt in a 2000 hydaui sonata


Below is a diagram for a 2000 Sonata with a 2.5L engine. No diagram for a 2.4L engine is available.

2000 Hyundai Sonata 2.5L

greg_margo_14.jpg

Jul 06, 2011 | 2000 Hyundai Sonata

1 Answer

2004 ford taurus chirping noise when engine revs


Hello, There are several things which can do this. First, cut off the A/C and then rev the engine as before. If the chirping goes away, the noise was either the A/C clutch or the Serpetine belt slipping with the load. For the A/C clutch, you can try a little rust removal between the drive plate and the pulley with the engine OFF. You can use sandpaper and try to knock off the rust. Then put a little oil on to condition the metal. Then try it with the A/C on.

If the chirp is still there, you have to check bearings on the Pulley tensioner, Alternator, Water pump, and Power steering. It is possible for the Pulley tensioner to have a weak spring or you may have a stretched Serpetine belt. This condition would cause the belt to skip under a load. If the belt is checked with small cracks, just replace the belt. Take off the tensioner and compare the spring tension and wobble in the pulley to a new unit at the Autoparts store.

If still no success, the chirp could be a water pump bearing. The old way off using a piece of wood on the housing of a part while the engine is running is dangerous, but effective. I believe you should have already found your problem before this measure is needed. Dry Serpetine belts make quite a lot of noise and is probably your problem.

I hope my Solution is very helpful to you.

Jun 28, 2011 | 2004 Ford Taurus

1 Answer

Need diageam on how to replace serpetine belt


im assuming you have a 4.3L?
but this will also work for the 5.0 and 5.7
28fe391.gif

Jan 23, 2010 | 2000 Cadillac DeVille

1 Answer

Power steering loss, overheating, dash board power


It sounds to me like the serpetine belt broke, DO NOT continue to drive it. The water pump (for engine cooling), the power steering pump, and the alternator (electrical system) are no longer operating. Have it towed to a shop or have someone put a new belt on it.

Jan 04, 2010 | 2000 BMW 5 Series

2 Answers

Need diagram how to install serpetine belt for my 1997 pontiac


CLICK HERE - as you did not indicate the accessories installed.

Thanks for using FixYa - a FixYa rating is appreciated for answering your FREE question.

May 27, 2009 | 1997 Pontiac Bonneville

2 Answers

What is the serpetine belt routing for a 97 chevy tahoe 5.7 ?


looking down onto engine feed belt down to your left around crank pulley, route up putting back side of belt around w/pump then continue rest of belt around outside of remanning acc. leaving top idler last. put 3/8 drive ratchet into tensioner and rotate down slipping belt over idler

Dec 21, 2008 | 2004 Chevrolet Tahoe

1 Answer

Drive belt tensioner pulley


the tensioner pulley is a small plastic or metal wheel about 3 inches big ...center of engine....

Dec 11, 2008 | 2006 Hyundai Sonata

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

111 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8172 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...