Question about 1989 Dodge Ram 50

1 Answer

Got 1989 dodge ram van 5.2 at idel it run rought

Got 1989 dodge ram van 5.2 at idel it run rought did pugs wires cap rotor and replaced carb

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that gotĀ 5 achievements.

    Vice President:

    An expert whose answer gotĀ voted for 100 times.

    Champion:

    An expert who has answered 200 questions.

  • Contributor
  • 245 Answers

Check for a leak at the intake manifold you can use some soap in a spray bottle spray along the intake and heads it will change the idle if its leaking
let me know if this helps

Posted on Jul 13, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Miss fire #6 cyl 2000 dodge 3500 van 5.9 egine


100 PSI is way to low, I think you have a burnt valve. Check the cylinder compression on all cylinders, no cylinder should be 5% lower than the highest cylinder pressure measured or the engine will run rough or misfire.

Jan 31, 2017 | 2000 Dodge Ram 3500

1 Answer

How to replace a 1989 Dodge Ram d100 distributor cap and rotor


Label or mark the wires before removing the cap, this is very important. Make sure the new cap goes on just like the old cap came off. The rotor is under the cap and should slide off by pulling up on it again make sure the rotor goes on the same. The rotor should be able to be put on only 1 way but make certain. Good luck.

Nov 27, 2015 | Dodge Cars & Trucks

1 Answer

I have 2000 ram 1500 van, had the idler pully seize and made the serpentine heat up and fall off. drove the van about 5 minutes and turned it off. Got parts to to repair the problem, when I went to start...


Try disconnecting the battery

You do know that the rotor,cap,cam
sensor etc wasn't the way to start a
diagnostic process?

Did it go into Fail Safe from over heating?

Mar 03, 2011 | 2000 Dodge Ram 1500 Truck

1 Answer

How do I replace magnetic pickup in my 1989 dodge ram 150


Remove cap rotor disconnect wires from distributor remove one screw on each side of distributer and lift out

Feb 08, 2011 | 1989 Dodge D150

1 Answer

P1281 on a 2000 dodge 3500 van I have replaced the fuel pump crank sensor plugs wires cap rotor running out of $$$$ fast


My resources say P1281 is engine is cold too long. That would lead me to possibilty of faulty thermostat, or something else in cooling system. What exactly are you getting for symptoms? No start, poor starting, poor running, ?

Nov 28, 2009 | 2000 Dodge Ram 3500

2 Answers

We replaced the distributor cap and rotor on our Dodge Ram Van 1500, but one wire popped off as we were working and we aren't sure they are in the right order anymore. How do we find a diagram to help us...


the firing order is usually stamped on the engine itself. Take off the distributer cap and turn the ignition to see which direction the rotor is turning.

The distributer cap has the number 1 plug marked . After finding the firing order, place the wires 1 where the cap is marked then in the direction the rotor is turning (ie:clockwise or couterclockwise). Keep looking . Most every motor I have seen has the firing order maked right on the engine.Or the owners manual ?

Oct 28, 2009 | 2001 Dodge Ram 1500 Truck 2WD

1 Answer

Our 1998 Dodge Ram 1500 van won't start arfter it has sat over night and it has rained. It takes an hour of trying to start it before it will fire up again. Any theories or solutions?


I've got a 95 Dodge 1500 Ram pickup. It has the same problem. I've got a 5.9 engine in it and the distributer is located right under the seam where the hood closes against the cowl panel. I suspect moisture is somehow working it's way into the distributer cap. Try replacing the distributer cap & rotor. If at night when you open the hood with engine running and don't see a "Light Show" from the wires I would spray the ends going in the cap with WD 40. If you do see a "Light Show" replace the wires, and then spray the ends with WD 40. It displaces water and moisture. This should cure your problem.

May 04, 2009 | 1999 Dodge Ram

1 Answer

Need a distributor wiring diagram for a 1989 dodge 150 van 3.9L


The firing order is 1-6-5-4-3-2 in a clockwise direction. Number 1 should be marked on the cap. 1 3 5 are on the driver side, 2 4 6 on the passenger side. I hope this helps.

Apr 10, 2009 | 1989 Dodge D150

1 Answer

ROTOR CAP


firing order is 1 8 4 3 6 5 7 2 (clockwise)

Please rate this solution.

Jul 04, 2008 | 1989 Suzuki Samurai

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

222 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

77169 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...