Question about 2000 Toyota Land Cruiser

1 Answer

What could be the viscosity of oil used in differential limited slip rear axle of prado

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Toyota Master
  • 22,156 Answers

80/ 90 EP oil its thick and a horrible smell

Posted on Jul 13, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 97 vzj95 prado 3.4lt v6 Recently the front diff seized and I've replaced it but now on turns while accelerating I'm hearing a clunk from the rear diff... Is this a wind up issue? Thanks


Yes it is a wind up of the axles and not the drive shafts. Your car has a limited slip diff and it is locking up.
When you are accelerating the diff locks up and your wheels are rotating at different rates while turning. This causes the axles to twist until the pressure causes the Limited Slip Diff to slip.
My guess would be that someone has changed the diff oil with non Limited Slip Diff oil.

May 12, 2015 | Cars & Trucks

1 Answer

I changed my Prado 2007 rear Differential LSD type, we have put Mobil 1 LS, 75W-90 diff oil. I used for 4 days and noticed some jerking when doing turns. Immediate drained and put Whiz synteq mt1 80W90...


II think I would try some Motorcraft XL-3 Friction Modifier. That is what Ford uses to fix the same problem in their Limited Slip differentials. You can find it online or at any parts house that carries Motorcraft.

dttech_13.jpg

May 04, 2011 | 1997 Toyota Land Cruiser

1 Answer

Where do I install the rear-end oil on a Dodge Ram 1500


I supose you are talking about the rear axle? if so, unscrew the bolts of the rear axle's cover and let the oil flow out into a container. once it's empty, clean the cover and the surface on the axle where the cover goes on to, apply a seal onto the cover and put the cover back on and screw al of the bolts back into place and tighten them. you will find a rubber plug in the cover, take it out and fill the rear axle untill the liquid comes out of the plughole. Put the rubber plug in and you're done! Watch out if you got al limited slip differential, you will need to put an additive into the oil so you won't burn the clutches of you limited slip differential.

Dec 09, 2010 | 2004 Dodge Ram 1500

1 Answer

How much oil do you put into the differential?


000 DODGE TRUCKS DURANGO 5.9L 8-cyl Engine Code [Z]
Limited Slip Differential, Rear 8.25-9.25 W/ TT......GL-5* All TEMPS......75W-140
Standard Differential, Rear 8.25-9.25 W/ TT......GL-5 All TEMPS......75W-140
Limited Slip Differential, Rear 8.25-9.25 W/O TT......GL-5* All TEMPS......75W-90
Standard Differential, Rear 8.25-9.25 W/O TT......GL-5 All TEMPS......75W-90
Note:Trak-Lok axles require Mopar limited slip additive limited slip additive 04318060 or equivalent
Differential, With 7.25 RingGear Rear..........1.4 liters Fill no higher then 3/4 inch below plug hole.
Differential, With 8.25 RingGear Rear..........2.1 liters Fill no higher then 1/4 inch below plug hole.
Differential, With 9.25 RingGear Rear..........2.3 liters Fill no higher then 5/8 inch below plug hole.
Thank you for using fixya and good luck

May 08, 2010 | 2000 Dodge Durango

1 Answer

Tring to find out what type oil goes in the rear axle of a 2003 dodge dakota 4x4 with a 4.6 engine


Mopart Synthetic Gear Lubricant 75W-90
NOTE:
Trac-Lok T differentials require Limited Slip Additive in the lubricant.
Trac-Rite differentials DO NOT require Limited Slip Additive.

Nov 28, 2009 | 2003 Dodge Dakota Club Cab

2 Answers

What kind of ATF goes in my 1992 cherokee?


Use ATF+4

Do not use Dexron or Mercon

Aug 08, 2009 | 1992 Jeep Cherokee Sport

2 Answers

Rear axle seal leaking how difficult would this be to fix


Not that difficult, raise and support the rear of the truck and remove the wheels. Might as well replace both sides so you know you have new seals, remove the differential cover and drain the fluid. Once differential is opened and cleaned , remove the axle "C" clip that hold the axle in place and slide the axle out. Once the axle is out remove the wheel seal and clean around the area. This would be a good time to replace the wheel bearing too since you have access to them and there not that expensive. Install the new bearing and seal, note make sure you oiled the bearing and seal before installing it back and take care when installing the axle back in and "C: clip. Use RTV silicon gasket maker to seal the differential cover and wheels back on and lower. If your lazy like i am, you can drain the differential fluid and replace it with a 50/50 mix with gear oil and Lucas engine oil additives. That may stop the leak and get you a few more miles. You gear oil is 75W-90 and the capacity is 2.6 liters and 3.6 liters if you have the 11.50 Ring gear. Good luck and hope this helps. 

Jul 03, 2009 | 2002 Chevrolet Tahoe

1 Answer

Dont know what lube to put in camaro limited slip rearend


Differential Fluid Type


Grade Synthetic
Viscosity 75W-90


Limited-Slip Differential Only
With Complete drain and refill, add 4 ounces (118 ml) of Locking Differential Axle Lubricant Additive, GM P/N 1052358 in Canada use P/N 992694 or equivalent

May 13, 2009 | 2001 Chevrolet Camaro

1 Answer

Replace left rear axle seal 1999 ford explorer


Axle Shaft Removal
  1. Raise and support the vehicle. For additional information, refer to Section 100-02 .
  1. Remove the wheel and tire assembly. For additional information, refer to Section 204-04 .
  1. Remove the differential housing cover (4033).
    1. Loosen the bolts and drain the lubricant from the rear axle housing (4010).
    1. Remove the bolts.
    1. Remove the differential housing cover.
Remove the rear brake disc (2C026). For additional information, refer to Section 206-04 .
  1. sxn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Turning the differential case (4204) or an axle shaft (4234) with the differential pinion shaft (4211) removed will cause the differential pinion gears (4215) to fall out of the assembly and damage the components.
    Remove the differential pinion shaft.
    1. Remove the differential pinion shaft lock bolt.
    1. Remove the differential pinion shaft.
  2. sxn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage the rubber O-ring in the U-washer groove.
  3. Remove the U-washer (4N237).
  4. Push the axle shaft inboard.
  5. Remove the U-washer.
Reinstall the differential pinion shaft.
  1. Install the differential pinion shaft.
  2. Install the differential pinion shaft lock bolt finger-tight.
  3. sxn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage the wheel bearing oil seal (1177).
    Remove the axle shaft.
-----------------------------------------------------------------------------------------------------------------
Seal Removal
  1. Remove the axle shaft (4334). For additional information, refer to Axle Shaft in this section.
  1. sxn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Never remove the wheel bearing oil seal (1177) by itself. Always remove the rear wheel bearing (1225) and the inner wheel bearing oil seal at the same time.
    NOTE: If the wheel bearing oil seal is leaking, the axle housing vent may be plugged with foreign material.
    Using the special tools, remove the rear wheel bearing and wheel bearing oil seal together.
6c7eb46.gif Installation
  1. Lubricate the new rear wheel bearing.
    • For 4.0L SOHC and 4.0L EI with limited slip rear axles and 5.0L vehicles, use SAE 75W-140 High Performance Rear Axle Lubricant F1TZ-19580-B or equivalent meeting Ford specification WSL-M2C192-A.
    • For 4.0L SOHC and 4.0L EI with conventional rear axles, use SAE 80W-90 Premium Rear Axle Lubricant XY-80W90-QL or equivalent meeting Ford specification WSP-M2C197-A.
  1. Using the special tools, install the rear wheel bearing.

ece7d89.gif
  1. Lubricate the lip of the new wheel bearing oil seal.
    • Use Premium Long-Life Grease XG-1-C or equivalent meeting Ford specification ESA-M1C75-B.
  1. Using the special tools, install the wheel bearing oil seal.
c21e27d.gif
  1. Install the axle shaft. For additional information, refer to Axle Shaft in this section.

Feb 22, 2009 | 1999 Isuzu Rodeo

Not finding what you are looking for?
2000 Toyota Land Cruiser Logo

115 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8172 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...