Question about 1990 Eagle Talon

1 Answer

On the distributor how are plug wires numbered

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 68 Answers

Ok pending engine
2.0 without dis 1234
13
24
with 2.0 dis 4
3
2
1 4123

3.0 1 2 3
4 5 6 3
6 5
C
2
1 4
hope this helps you wasn't that specific



Posted on Jul 13, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace a distributor


disconnect the cable from the negative battry terminal. position the engine with number one cylinder at TDC on the compression stroke this mean you can take number one spark plug out with the engine cool place your thumb over the spark hole and have some one turn the engine over and and feel the presure by your thumb when you feel pressure stop turning engine take the distributor cap and make sure the rotor is pointing to number one spark wire in distributor cap if not you may have to turn the engine a little with your hand apply a paint mark on the edge of the distributor body directly below the rotor tip. also make a mark on the distributor base to the engine to ensure the distributor can be re-installed in exactly the same position as originally installed disconnected the coil wires from the distributor cap electrical connector, spark plug wires from the spark plugs remove the distributor hold-down bolt and pull out the distributor.

Jun 04, 2014 | 1995 Land Rover Discovery

1 Answer

Spark plug wiring from distributor cap to spark plugs on a 95 honda civic dx 1.5 liter 16 valve sohc


If you look at the distributor cap from the wires side carefully, you would find either a line mark on one of the outer side of four holes (where the spark plug wires are inserted) or the numbers printed on the top of distributor cap (1,3,4,2). Fix one end of the longest high tension plug wire into number 1 hole or the one marked with a line mark on the distributor cap and the other end on spark plug number 1 (the number 1 plug is toward the pulleys and the belts side, then No 2, No 3 and No 4). While standing in front of right wheel you will see the distributor cap in front of you. The rotor moves clock wise. After you fix the 1st cord, next comes number 3 plug wire. Insert one end of the cord into the next to 1 on the right hand side and press the other side of the cord on spark plug number 3. Next to 3 is the cord number 4 and the last one is number 2.

Mar 22, 2013 | Honda Civic Cars & Trucks

2 Answers

Not sure how to replce spark plug wires from the distributor need help please send info


change one spark wire at a time on the distributor.buy new set of spark plugs wires remove them from box.match old wires with new wires to use the correct length to each cylinder.now if you need to change distributor cap.mark location distributor cap.number tag plug wires on the distributor cap so you can remove plug wires on distributor cap so you can replace cap and rotor and put wires back on the distributor cap in correct place.remember change one plug wire at a time so you wont get confuse.

Apr 15, 2011 | 1992 Ford Tempo

1 Answer

I need to replace ,the rotor button...


TAG OR NUMBER ALL SPARK PLUG WIRES ON THE DISTRIBUTOR CAP BEFORE REMOVING CAP. SO YOU CAN PUT PLUGS WIRES BACK IN THE ORIGINAL POSITION. WHEN ALL PLUGS WIRES ON DISTRIBUTOR CAP BEEN NUMBER.REMOVE ALL PLUG WIRES ON CAP.THEN REMOVE THE DISTRIBUTOR CAP.THEN MARK ROTOR POSITION WITH SHARPIE MARKER THEN REMOVE THE ROTOR.

Mar 02, 2011 | Chevrolet 1500 Cars & Trucks

1 Answer

I need a wiring diagram for the ignition control module and distributor on a 2.8 litre v6 motor


OKAY STANDING IN FRONT OF ENGINE ON LEFT SIDE CYLINDERS FACING YOU IS 1 3 5 ON RIGHT SIDE DRIVER SIDE CYLINDERS FACING YOU IS 2 4 6 LOOKING AT DISTRIBUTOR CAP NUMBER 1 SPARK PLUG ON CAP IN THE 9 OCLOCK POSITION YOUR NUMBER 5 SPARK PLUG ON DISTRIBUTOR CAP IN 6 OCLOCK POSITION .STARTING AT NUMBER 1 SPARK PLUG ON CAP COUNTING CLOCKWISE COUNTING 1 2 3 4 5 6 THATS YOUR SPARK PLUGS WIRES ON CAP TO ENGINE PLUGS. 6 PLUG WIRE ON CAP IS AT 7 OCLOCK POSITION.

Feb 07, 2011 | 1988 Pontiac Firebird

1 Answer

How do i know in what order do the spark plug wires go in the the distributor cap?


Hopefully the number one wire is indicated on the distributor
cap with a 1. As you look at the engine from the front the
number one cylinder is the first on the right (4-3-2-1). Going
clockwise on the distributor connect the number 1 wire to the
number 1 cylinder spark plug. the next terminal on the distributor
is no 2 then 3 then 4 and your are done. Better yet always replace
or remove wires one at a time returning them to their original positions.

Jan 08, 2011 | 1998 Honda CR-V

3 Answers

I changed the spark plugs and wires on my chevy s10 2wd pick up, which is a 4 cylinder and now it will not turn over. I might have the wires mixed up on the distributer cap. Can someone show me a picture...


GET A PIECE PAPER DRAW A LARGE CIRCLE TOP UPPER HALF CIRCLE LEFT TO RIGHT WRITE NUMBERS 1 AND 3 BOTTOM HALF CIRCLE LEFT TO RIGHT RIGHT NUMBERS 2 AND 4 THAT YOUR DISTRIBUTOR SPARK PLUGS WIRES LOCATION.STANDING ON SIDE OF ENGINE WHERE DISTRIBUTOR IS LOOKING DOWN AT DISTRIBUTOR 1 AND 3 FIRST TWO SPARK PLUGS TERMINALS NEXT TO ENGINE. AND 2 AND 4 SPARK PLUGS TERMINAL ON CAP FACING YOU. THIS IS CYLINDERS LOCATIONS STANDING IN FRONT OF ENGINE.RUN WIRES FROM DISTRIBUTOR CAP TO PLUGS TO THE ENGINE SPARK PLUGS.

Oct 17, 2010 | Chevrolet S 10 Cars & Trucks

2 Answers

I took of*** my spark plug wires working on my small block 350 pickup and I don't remember the the firing order to put the new wires back on. Is there a diagram anywhere or is it even that difficult to...


Next time number each lead before you remove it and no. the dissy cap as well

The firing order, which should be cast into the intake manifold, for the chevy small block V8 is 1-8-4-3-6-5-7-2. The firing order is the numerical sequence in which the spark plugs are fired. The insertion position of each spark plug wire around the circumference of the distributor cap can be found according to a clock face. The insertion sequence determines the firing order. The firing order is followed clockwise around the distributor cap starting from the 6:30 position with the 6:30 position being the number one cylinder spark plug wire.
On classic chevy small block engines that use ignition breaker points instead of electronic ignitions, the number one cylinder is the one immediately clockwise of the small metal sash cover on the distributor cap. The firing order starts here. There is no sash cover on the distributor cap for GM HEI electronic ignitions, and the firing order is the same, but starting at the 5:30 position.
The firing order makes sense if you know how the cylinders are numbered. The number one cylinder is the front most on the drivers side and 2 being the front most on the passenger side. From front to back, the cylinders are odd numbered on the drivers side, and even numbered on the passenger side.
See the diagram; Click to open a printable larger image in a new window. The firing order starts with the number one cylinder. We would connect the number one spark plug wire to the distributor cap terminal in the 6:30 position. distributor.pngSince the next cylinder in the firing order is 8 (passenger side rear), we connect the number 8 spark plug wire to the next distributor cap terminal (approximately 7:30 position) in the clockwise direction from number one. You need to be sure you continue the firing order in the clockwise direction around the chevy small block distributor cap from the last installed spark plug wire. Setting the rest of the firing order is just a matter of repetition. Be sure to count the spark plugs from front to back on each side of the motor to identify the correct cylinder number in the firing order.

Jun 21, 2010 | Cars & Trucks

1 Answer

In what order do yu arrange the plug wires on the distributor cap or a 1990 gmc 350


1-8-4-3-6-5-7-2 Distributor turns clockwise Number one should be in the 5 oclock position. You should be able to draw an imaginary straight line between the coil tower and number one tower on the cap and the number one spark plug.

May 15, 2009 | 1990 GMC Sierra

2 Answers

1987 GMC Jimmy Distributor cap and Rotor replacement


A diagram may not be needed as its a reasonably easy fix to do on your own.the distributor ca p will only fit on properly one way because at the base of the cap locaters can only fit the distributor if they line up.When doing the spark plug leads do them one at a time and if nessecary write or mark leads as 1,2 etc .The rotor can only fit on one way but put a mark on the distributor to show where the rotor was pointing when you took it off and if it still points there when the new one is fitted.When changing distributor cap and leads they have to go to the correct place.Pays to mark the outside of distributor cap where the locating bits are On the new and old one.Fit the new cap and rotor then take a spark plug lead and fit to new cap 1 at a time.You can tell by lining up the marks on the outside of the distributor cap when you hold them one on top of the other.Good luck

Oct 20, 2008 | 1987 GMC Jimmy

Not finding what you are looking for?
1990 Eagle Talon Logo

Related Topics:

33 people viewed this question

Ask a Question

Usually answered in minutes!

Top Eagle Experts

yadayada
yadayada

Level 3 Expert

76118 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Stewart Dibbs

Level 2 Expert

308 Answers

Are you an Eagle Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...