Question about 1998 Isuzu Rodeo

2 Answers

How do you remove old u-joint from driveline? on 1998 isuzu rodeo,i have tryed the hammer, its press on tight.

Posted by on


2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert who has written 7 tips or uploaded 3 video tips

  • Master
  • 642 Answers

Nothing wrong with the above advise. Just one more thing. Hopefully you first tried removing the circlips that hold the joint in place. Some units' circlips are obvious as they sit on the outside of the u-joint's cup. Certain models do however have a circlip between the u-joint centre piece and the inside of the driveshaft.

Posted on Jul 20, 2010

  • Level 1:

    An expert who has achieved level 1.


    An expert that has over 10 points.


    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 8 Answers

I use heat, use torches to heat the area around the ujoint, then use the hammer again, be careful where you are hitting you can knock the alignment of the shaft out & you will have to replace the shaft. The weld linnes on the shaft are a good spot, also use extreme care not to heat the ujoint its self up too much, they have been know to explode with heat. Wear googles!!! Good luck

Posted on Jul 13, 2010


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

I have a 2004 Isuzu Rodeo and developed tight spots in the steering. Is there a way to tell if it's the steering pump or rack?

have your mechanic check the small U joint in the lower part of column close to axle . My toyota just had similiar problem and that U joint was seized up . non greasable u joint and cost 300 to replace it .steers like a new truck now tho with 1 finger

Apr 25, 2015 | 2004 Isuzu Rodeo

2 Answers

How to fix a 2003 Isuzu Rodeo Sticking Shifter

finesse! seriously, I'm the only one who can get my rodeo out of park... try pulling the shifter SLIGHTLY towards you and left BEFORE you push in the button. works everything's for me. good luck!

May 17, 2014 | 2003 Isuzu Rodeo

1 Answer

Isuzu rodeo troubleshooting

Sounds like a ball joint seeing that the cv joints were replaced, have you had it aligned?

May 07, 2014 | 1998 Isuzu Rodeo

1 Answer

I need a digram showing me how to change the shocks on my 1999 isuzu rodeo

It is quite easy really, Remove the wheel on the corner you want to change, The back ones have one bolt at the top and one at the bottom, Simply unbolt the old one and fit the new one, The front ones are pretty much the same but they may have 2 bolts at one or both ends, Simply unbolt and fit the new ones, just make sure the replacements are bolted in tightly.

Mar 06, 2012 | 1998 Isuzu Rodeo

1 Answer

How do i replace the cv joints on a 1998 isuzu rodeo?

I have a '97 Rodeo and attempted to change the cv joints myself. Unfortunately, they were assembled through brackets that were bolted to the frame, and could not just be pulled straight out without taking the brackets off. The bolts were extremely rusted and would not budge. I ended up paying a local garage to change them for me ( and I NEVER let a garage touch my vehicles) as it was impossible to tackle without car lifts and air compressor tools. Was well worth the $500 to pay someone else to change them.

Mar 29, 2011 | 1998 Isuzu Rodeo

1 Answer

It's getting harder to shift gears for my 1998 isuzu rodeo. All gears 1 2 3 4 5 and reverse .What can i do to fix it? The fluid looks dark and dirty in the place that you put fluid in . I have tried to add...

problem is caused by shifter linkage bushings swelling causing joint to become tight and siezedto fixbuy linkage bushings and pins dissasemble pry old bushings clean sand journals of rust install new bushings use grease replce the pin/bolt check to see if the joints move freely

plz leave me a comment if you need more info reply

Jan 19, 2011 | 1998 Isuzu Rodeo

1 Answer

2001 isuzu rodeo has intermittent starting problems

check battery cables & terminals for tightness & corrosion.also check at starter.check starter bolts & actual starter for looseness.if no problems found your starter may be on its way time it happens hit starter with hammer or heavy object if it starts right up get ready to replace it.good luck

May 20, 2009 | 1999 Isuzu Rodeo

2 Answers

Cv joints wont come out of diff housing (95 Rodeo 4x4 diesel)WHY

You might have to remove the diff cover and remove the lock rings from inside the diff.

Feb 15, 2009 | 1995 Isuzu Rodeo

1 Answer

Ball joints

I attempted that once, but I had to take mine to a professional as the joint is pressed in place with a special tool.

If you don't mind a little risky work here is a method with a hammer and a jack you can try.

Jack Ball Press

Jul 11, 2008 | 2000 Isuzu Rodeo

Not finding what you are looking for?
1998 Isuzu Rodeo Logo

Related Topics:

177 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts


Level 3 Expert

81342 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14423 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides