Question about 1994 Chrysler Concorde

1 Answer

Where is the coolant fan switch located on 1994

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 68 Answers

On or near the thermostat housing


Posted on Jul 13, 2010

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: where is the coolant sensor switch ??

FAN SENSOR SWITCH IS LOCATED ON ENGINE BLOCK BELOW THE ALTERATOR , IT HAS A 2 WIRE PLUG ATTACHED TO IT.

Posted on Jun 24, 2009

projdoc
  • 2237 Answers

SOURCE: coolant fan switch

it's hooked up to the temperature sensor. if you don't get a temp light on, the sensor might be bad. it's usually located where the upper radiator hose goes into the engine. also check your thermostat.

Posted on Aug 12, 2009

duane_wong
  • 6826 Answers

SOURCE: location of coolant temperature sensor and

Removal & Installation To Remove:

  1. Before servicing the vehicle refer to the precautions at the beginning of this section
  2. Remove or disconnect the following:
    • Engine coolant into a suitable container to a level below the ECT sensor gm_car_cad_sev_ect_loc.gif

    • ECT sensor harness connector (A)
    • ECT sensor
To Install:
NOTE: Use care when handling the coolant sensor. Do not drop damage to the coolant sensor will affect the operation of the fuel control system.
NOTE: Replacement components must be correct for the application. Components requiring the use of the thread locking compound, lubricants, corrosion inhibitors, or sealants are identified in the service procedure. Some replacement components may come with these coatings already applied. Do not use these coatings on components unless specified. These coatings can affect the final torque which may affect the operation of the component. Use the correct torque specification when installing components to avoid damage.
  1. Coat the sensor threads with GM P/N 1050805 sealer or equivalent
  2. Install or connect the following:
    • ECT sensor
      1. Torque to: 15 lb-ft. (20 Nm)
    • ECT sensor harness connector
    • Engine coolant
  3. Start the engine then idle until normal operating temperature is attained.
  4. Recheck coolant level and top off as needed.
  5. Test drive the vehicle.
--- I couldn't find a reference for the 'fan coolant relay switch' although I'm sure there is one on this car.

Posted on Sep 01, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why is are the electric fans always on?


Probably a stuck cooling fan switch, or relay. The fan switches on most Chryslers are screwed into the radiator, and easily accessed. Make sure you have a catch pan for your coolant, and wait till the system is completely cold.

Feb 17, 2013 | 1994 Chrysler New Yorker

1 Answer

Where is cooling fan relay andcooling fan temp switch


The coolant fan relay is located on the Right Hand front of the engine compartment on the relay bracket. Your temp sensor is located on bottom part of radiator. Hope this helps.

Aug 16, 2011 | 1994 Buick Century

2 Answers

The fan that is behind the radiator isnt turning on and my 1994 chevy cavalier keeps overheating


test your fan motor.run b+ and ground to your motor and see if it runs.if it doesnt it is probably your coolant fan switch located on the cylinder head or the coolant fan relay.hope this helps.keep posted.

Feb 23, 2011 | 1994 Chevrolet Cavalier

2 Answers

Hello my 1994 camry toyota has a problem holding the water. We replaced the thermostat,fan switch,radiator cap, and it keeps comsuming the water. What do you think the problem might be? Javier


Javier, have you checked the coolant overflow tank for holes, cracks, or loose hose? When the engine in your car heats up, the coolant expands. The coolant overflow tank (located near the radiator) takes up any coolant that is forced out of the radiator. If the tank is damaged or not connected to the radiator correctly, the coolant will not siphon back into the cooling system when the engine cools off.

Dec 07, 2010 | 1994 Toyota Camry

1 Answer

How do you replace the coolant tempature switch on a 94 Ford Escort wagon, 1.9 Liter


The coolant temperature switch and fan control switch are located sie by side, mounted in the steel portion of the heater hose that runs from the thermostat housing to the firewall, it is underneath the air intake tube and the ignition coil pack, mounted to the back of the cylinder head. Either drain out some coolant or be very quick, and you can unplug and unscrew each switch from the hose and replace it with a new one. Make sure the engine is cold. After replacing make sure to check the coolant level add as neccessary. The single wire connector switch is for the guage, and the other is for fan control. Hope this helps, let me know.

Jun 11, 2010 | 1994 Ford Escort

1 Answer

1994 buick paqrk avaune fan dosnt come on


the cooling fan will only run when the vehicle reaches a certain temperature around 100 degrees Celsius. it does this using a temperature switch (usually the coolant temp sensor or a temperature switch located on the radiator). the switch sends power to a relay in the engine compartment (should be marked or you can trace the wires from the fan directly to it). the relay, when activated, sends power to the fan. you should be able to figure it out using a test light. check fuses first though. probably a bad temperature switch. if you do not know how to figure out this problem with the information provided you should probably have a technician check it out for you.

Mar 23, 2010 | 1994 Buick Park Avenue

1 Answer

Coolant fan switch


it's hooked up to the temperature sensor. if you don't get a temp light on, the sensor might be bad. it's usually located where the upper radiator hose goes into the engine. also check your thermostat.

Jan 13, 2009 | 1994 Toyota Camry

Not finding what you are looking for?
1994 Chrysler Concorde Logo

Related Topics:

40 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...