Question about 1997 Chevrolet Lumina

1 Answer

The bar just on the inside of the rear passenger wheel going from the middle of the wheel toward the front up onto the frame. What is it called

Posted by Anonymous on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 326 Answers

Lower trailing arm or lower control arm

Posted on Jul 13, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Lower part of wheel is bending under car


The sway bar gives from side to side so I doubt your problem is in that. Of course it is really hard for me to pinpoint your problem without inspecting the vehicle, how hard did the vehicle hit the curb? If it hit it pretty hard and severely bent the lower control arm, I would suspect that you have some frame damage.

You need to really inspect the frame where the lower control arm mounts, it may help to look at the other side and compare it to the damaged side. You'll be looking for slight wrinkles or bends in places near where the control arm mounts or follow back and keep looking for any signs of slight signs of damage.

And, are we talking about the front, rear or both on the vehicle?
If it's the rear, the rear is weaker than the front. Follow the frame rail all the way towards the middle and look for signs of damage.

If you look closely, you should be able to find the damaged area.
It being a '94 it doesn't take much damage for your insurance to total the vehicle out, (if you happen to have full coverage insurance and file it.)
I hope this may help.

Dec 23, 2017 | 1994 Honda Accord

1 Answer

Bushing near passenger side rear wheel is worn out. what is this rod called on a 2001 buick lesabre custom?


most likely called a control arm bushing. yes some can be replaced and others the whole are is replaced.

Sep 01, 2017 | Cars & Trucks

1 Answer

Condensation water from air conditioner soaking front and rear passenger carpets. Where is drain located?


98 grand cherokee limited 5.2L same problem found leak not from heater box but from drain mount on firewall under the glove box not behind it. drain line should be located behind right front tire in the frame. Turn your wheels hard left look inside fender well right side towards back side. hole in frame where drain line should come out.

Sep 10, 2012 | 1997 Jeep Grand Cherokee

1 Answer

Piece that goes from rear brake drum to frame got bent. what is this part called and what does it do?


There are three, we'll call them bars, that go to the rear spindle on your century. The one that goes forward toward the rear door of the car is called a trailing arm. The other two which goe towards the center of the car are called lateral arms, and there is a front and rear. The rear lateral arm is usually the one that gets bent. These three arms position the lower end of the strut/spindle assembly, and if one or more are bent, your rear wheel alignment will be out of whack, and your car will drive funny and you will wear out your tires.

Aug 19, 2011 | 2002 Buick Century

2 Answers

Where is the fuel filter located on a 1997 S-10 Chevrolet pickup?


On the frame rail running under the driver side, between front & rear wheels.

Aug 25, 2010 | 1997 Chevrolet S-10 Pickup

1 Answer

Replace broken sway bar for a 1996 ford windstar


Section 04-01: Suspension and Wheel Hubs, Front 1996 Windstar Workshop Manual REMOVAL AND INSTALLATION Stabilizer Bar Removal
  1. Raise and support the vehicle. Refer to Section 00-02 .
  1. Support vehicle with hoist or safety stands behind front sub-frame (5C145).
  1. stw~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: To avoid damage to the 6 mm drive hole in the front stabilizer bar link ball stud, do not use an Allen wrench to break loose or tighten or final tighten the front stabilizer bar link-to-shock absorber nut.
    Using care not to damage the front stabilizer bar link ball stud seal, remove the RH and LH front stabilizer bar link-to-front shock absorber nut.




  1. Using care not to damage the front stabilizer ball link stud seal, remove the RH and LH front stabilizer bar link-to-front stabilizer bar nut.
  1. stw~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Use extreme care not to damage the ball joint boot.
    With another set of support safety stands under front sub-frame, remove two rear sub-frame retaining bolts. Lower rear of the front sub-frame to obtain access to stabilizer bar brackets (5486).
  1. Remove front stabilizer bar bracket bolts, stabilizer bar brackets, stabilizer bar bracket insulators and front stabilizer bar (5482) as required.
Installation
  1. Clean front stabilizer bar to remove dirt and contamination in area of stabilizer bar bracket insulator installation position.
  1. Lubricate inside diameter of new stabilizer bar bracket insulator with Rubber Suspension Insulator Lube E25Y-19553-A meeting Ford specification ESF-M99B112-A or equivalent. Do not use any mineral or petroleum based lubricants as they will deteriorate the rubber stabilizer bar bracket insulators.
  1. Install new stabilizer bar bracket insulators onto front stabilizer bar and position them in approximate location.
  1. Install stabilizer bar bracket on stabilizer bar bracket insulators and install new bolts. Tighten to 55-63 Nm (40-46 lb-ft).
  1. Raise front sub-frame and install new front sub-frame-to-body retaining bolts. Tighten to 115-132 Nm (85-97 lb-ft).
  1. Install front stabilizer bar link (5K483) to front shock absorber. Use care not to damage link ball joint boot seal.
  1. stw~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: To avoid damage to the 6 mm drive hole in the front stabilizer bar link ball stud, do not use an Allen wrench to break loose or tighten or final tighten the front stabilizer bar link-to-shock absorber nut.
    Install a new front stabilizer bar link-to-shock absorber nut. Tighten to 90-100 Nm (66-74 lb-ft).

  2. 66a0f1a.gif

Apr 28, 2010 | 1996 Ford Windstar

3 Answers

Where is a fuel fliter on a 2003 ford crown victoria police car?


Go under the car and follow the gas lines coming off the top of the fuel tank back towards the fromt of the car and you will run into it.

Sep 30, 2009 | 2003 Ford Crown Victoria

1 Answer

Front Sway bar(Stabilizer bar)


please give good rating if this helps


Section 04-01: Suspension and Wheel Hubs, Front 1996 Taurus, Sable Workshop Manual REMOVAL AND INSTALLATION Stabilizer Bar Removal
  1. Raise vehicle on a hoist. Refer to Section 00-02 .
  1. Support vehicle with hoist or safety stands behind front sub-frame (5C145).
  1. sth~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Use extreme care not to damage boot seal. Do not use power tools to tighten nut, or bearing and seal damage will result. Install nut using hex hold feature to prevent the stud from rotating.
    Remove and discard nuts retaining stabilizer bar link (5K484) assembly to front stabilizer bar (5482) and front shock absorber (18124) with an 8 mm closed-end wrench and an 18 mm open-end wrench.


    ccf2026.gif

  1. Remove nuts retaining steering gear (3504) to front sub-frame, and move steering gear off the front sub-frame.
  1. With another set of support safety stands under front sub-frame, remove two rear subframe retaining bolts. Lower rear of the front sub-frame to obtain access to stabilizer bar brackets (5486).




  1. Remove front stabilizer bar U-bracket bolts and replacestabilizer bar brackets and/or front stabilizer bar as required. Discard lower suspension arm stabilizer bar insulator (5493) and bolts.
Installation
  1. Clean front stabilizer bar to remove dirt and contamination in area of stabilizer bar insulator installation position.
  1. Lubricate inside diameter of new lower suspension arm stabilizer bar insulator with Rubber Suspension Insulator Lube E25Y-19553-A or equivalent meeting Ford specification ESF-M99B112-A. Do not use any mineral or petroleum based lubricants as they will deteriorate the rubber lower suspension arm stabilizer bar insulators.
  1. Install new lower suspension arm stabilizer bar insulators onto front stabilizer bar and position them in approximate location.
  1. Install stabilizer bar bracket on front sub-frames and install new bolts. Tighten to 30-40 Nm (22-29 lb-ft).
  1. Raise front sub-frame and install new front sub-frame-to-body retaining bolts. Position steering gear onto front sub-frame and install retaining nuts. Tighten to 115-135 Nm (85-99 lb-ft).
  1. sth~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Use extreme care not to damage boot seal. Do not use power tools to tighten nut, or bearing and seal damage will result. Install nut using hex hold feature to prevent the stud from rotating.
    Install stabilizer bar link to front shock absorber and to front stabilizer bar, making sure that the stabilizer bar link is properly positioned. The letters "Top LH" and "Top RH" are moulded into the stabilizer bar link for correct assembly to the front shock absorber strut.
  1. Install new nuts and secure stabilizer bar link assembly to front stabilizer bar and front shock absorber. Tighten to 77-103 Nm (57-75 lb-ft) at front shock absorber strut and 47-63 Nm (35-46 lb-ft) at front stabilizer bar.
  1. Remove safety stands.
  1. Lower vehicle.

Apr 11, 2009 | 1995 Ford Taurus

1 Answer

Rear passenger side wheel facing inward


oh ok rear a frame ,rear tortion bar, rear srut rod ,hard to say with out looking at it the best way to find out is get the vin number call your local dealer and ask for parts and explain to them what it is and they even might send you a fax if you have a fax machine then you can call the local junk yard and get one or the dealer can order you one they are very helpfull

Jul 19, 2008 | 2001 Chevrolet Monte Carlo

Not finding what you are looking for?
1997 Chevrolet Lumina Logo

Related Topics:

113 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

Marvin
Marvin

Level 3 Expert

81400 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...