Question about 1993 Chevrolet S-10 Blazer

1 Answer

93 blazer is mi9ssing an back floors very hot

93 blazer is missing an back floors very hot

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert who has answered 200 questions.


    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 200 Answers

Check catayatic converter usually after dark it will be very red if it is bad

Posted on Jul 13, 2010


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

On my 93 chevy s10 4x4 blazer, my instrument panel worked before new motor was put in, after having the new engine put in, my fuel gauge, oil pressure, voltmeter, rpm, and my temp gauge all quit worki

Look for a missing ground strap from the engine to the body or frame. Remember the engine sits on rubber mounts so that ground strap is essential.

Feb 21, 2014 | Cars & Trucks

1 Answer

When my 93 blazer sits while it runs it shakes really bad and it seems like its missing.

check that your plug wires are all seated properly. also use an oil and fuel stabilizer, this usually helps with older vehicles. recommend seafoam for engines

Jun 08, 2011 | 1993 Chevrolet S-10 Blazer

2 Answers

I need the firing order for a 93 chevy blazer distributor.where is number 1?

Firing order for a 4.3 liter v6 1-6-5-4-3-2

#1 piston is the first spark plug drivers side front of engine.
Passenger side cylinders are 2 4 6
Drivers side cylinders are 1 3 5
Distributor rotates clockwise and the starting spot is marked with a 1 on the top of the distributor cap.
Make sure you note the position of the 1 on the old cap before you take it off so you don't rotate the new one 180 out

Jun 09, 2010 | 1993 Chevrolet S-10 Blazer

1 Answer

Ive got a full size blazer its a 93 and its a manuel engaded i put it in four wheel drive high or low and the front wont spin what could it be the blazer runs fine in 2 wheel hi

your transfer case could be burned out for 4 wheel and thats why your only getting the back wheels to turn. when was the last dif service done?

Jul 19, 2009 | 1999 Chevrolet Blazer

1 Answer

93 Jimmy Electronic 4 Wheel Drive

If the Blazer is the same Year. I think the years are 1992 to 1994 will work as long as it's the 4L60E, and you have the manuel transfer case to activate the 4WD.
Good luck and keep me posted.

Jun 03, 2009 | 1994 Chevrolet S-10 Blazer

1 Answer

1993 s10 blazer has hesitation

Hi everyone,

I had a very similar problem with my 93 S-10 Blazer. I thought it was just cold blooded. I'd start it and it would idle so rough and spit and sputter and it seemed as though the fuel was dumping right out the tail pipe! I placed the computer on it as my engine light finally came on but all it said was that the exhaust was rich. Well I know that! Thanks computer. So then I heard about a product called "Seafoam." It will clean the engine of carbon build up. There are three ways to use it, let the PCV valve **** it up, add it to the oil, or add it to the fuel tank.
I pulled the PCV valve out of the valve cover, removed the valve from its stem. turned the engine on then I reved the engine a bit from the throttle body while I placed the PCV stem inside the can of seafoam. While the can is being emptied you will see and SMELL a huge white cloud of smokey fog coming from the tailpipe. As soon as the can is empty let go of the throttle. If the engine does not stall on its own shut it off. Let it sit for 4 or 5 hours. Then start the may start a bit hard....and PRESTO!!! I was skeptical of this product as there are so many out there that claim to be the best but this one actually works!! My truck now runs and idles like never before. It even increased my gas mileage considerably. I'm going to wait another week then add another can to my full tank of gas so it will do a job on cleaning my injectors. This can of seafoam cost me only $11.00 dollars Canadian. Thanks Seafoam!!

Jan 11, 2009 | 1993 Chevrolet S-10 Blazer

2 Answers

93 blazer runs better when check engine light's on

Could be a temp sensor or similar too, and believe it or not, the price to have the vehicle scanned for codes, and fuel pressure tested if necessary, usually ends up being cheaper in the long run, rather than play hit & miss, and replace a bunch of parts by guessing.

Dec 11, 2008 | 1993 Chevrolet S-10 Blazer

1 Answer

93 chev Blazer

perhaps i missed something here... lowbeams and daytime lights are about the same.... be that as it may... the merely obvious thing is that the low beams are burnt out.... next thing would be that the relay for the day time lights could be defective... it's often mounted on the firewall.


Nov 12, 2008 | 2001 Chevrolet Blazer

Not finding what you are looking for?
1993 Chevrolet S-10 Blazer Logo

Related Topics:

55 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts


Level 3 Expert

82188 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22382 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides