Question about 2005 Ford F-150

1 Answer

The Power door locks on my 2005 F150 won't lock with button,FOB or when you engage Drive on tranny but will unlock with fob or button.What's wrong.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 984 Answers

I would say a broken wire in the door to a-pillar harness.

I have seen it a few times.

If you pull the switch panel, and check for power on the Light blue w/ black stripe wire, you might find it is dead.

This is assuming you already checked the fuses and the accessory delay relay.

Posted on Jul 16, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How do I program fob for mabilu maxx 2005


You have to go to a Chevy dealer. They have a hand-held computer they plug into your car to get it into programming mode. Probably cost $50-$60. Call them for an estimate.

Feb 15, 2015 | 2005 Chevrolet Malibu

1 Answer

Key won t unlock doors


lost the other fob>>> ?????
never own a car with 1 fob.
and if one fob messes up, the battery inside is dead. (or worse)
if just lock fails the button is bad, if one fob false, and they do
its just cheezy switch. (can be cleaned)
use the other FOB, if it fails, post.

Jan 25, 2014 | 2007 Honda CR-V

1 Answer

05 dakota doors lock with fob but won't unlock with fob


Your FOB has gone bad. Try your other FOB just to make sure and let me know ....

Apr 14, 2013 | 2004 Dodge Ram 1500

1 Answer

Power door lock switch?


Sounds like the drivers door lock switch is bad an as far as the auto start remote the contacts under the button get dirty and won't make contact, open the remote like changing the battery and you can probably get at the contact button, if it's a little carbon button they can be cleaned with a pencil eraser and then paper tower with a bit of rubbing alcohol, if it's an actual switch you can try spraying some contact cleaner into the switch. let it dry before you put the battery back in.

Nov 11, 2012 | Ford F-150 Cars & Trucks

1 Answer

Sorry my car was not listed so picked Altima 2003 Micra Intelligent key fob not working properly. Can drive the car but cannot open or lock the doors. Did get fob wet. Now dried out. Worked for first few...


You are going to need to check the power lock control moduel on the inside of the door panel. If the FOB appears to be working but the doors are not unlocking, you need to check this. I would also replace all fuses that control the locks. If both of these devices check out ok, you may need to replace your FOB. To check your power lock control moduel, manually lock and unlock your doors by pressing the lock button on the inside of the door. If it does not work, it is either the fuses or the power lock control moduel. If it works, your FOB has gone bad. Hope this helps! Please rate 4 thumbs up!

Apr 18, 2011 | Nissan Altima Cars & Trucks

3 Answers

I need to reset my peugeot 406 key fob


Had same trouble with my 406, fixing no problem, with new battery in fob, insert into ignition, turn key, BUT DO NOT START ENGINE, hold button for about 10 seconds release button and remove key from ignition, then try and see if doors lock on remote, if not try again, had to do this a couple of times, and it worked, sorry to say that now my key fob button has completely fell apart, through ware and tare

May 19, 2009 | 2005 Peugeot 405

1 Answer

How to program a keyless entry fob for 2005 gmc envoy - i am replacing the battery in my key fob every 5 days. I have to be right next to the car for it to work. Any idea what would cause this. I ordered a...


Seating in the drivers seat , make sure all doors are closed.Insert key into ignition, don't turn on yet.
Wait for the dome light to go out, then press and hold the door unlock button , make sure it is UNLOCK, while turning the key ON OFF ON OFF Twice , do not engage the started, just on to the point of being on. Release the unlock button,and your doors should lock, then unlock indicating programming mode.At this point hold down both the lock and unlock button on the key fob. After 30 seconds your locks should lock and unlock, indicating the fob is programmed. This must be repeated for all remotes, whether or not it be new or old. After all remotes are programmed, turn the key off and on again to exit programming mode.

May 18, 2009 | 2005 GMC Envoy

Not finding what you are looking for?
2005 Ford F-150 Logo

137 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...