Question about Mazda 626

2 Answers

Check engine light on

Where do I find the OBD1 codes for Mazda626

Posted by on

  • nellwyn49 Jul 12, 2010

    I also have a code 69

×

2 Answers

yadayada
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points
    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.
    Superstar:

    An expert that got 20 achievements.
    All-Star:

    An expert that got 10 achievements.

  • Mazda Master
  • 75,005 Answers

Diagnostic Trouble Codes OBD1
Mazda 02 Crank Position Sensor (NE Signal). 03 Cam Position Sensor (SGC Signal). 05 Knock Sensor. 08 Air Flow Sensor. 09 Engine Coolant Temperature Sensor. 10 Intake Air Temp. Sensor (Air Flow Sensor). 12 Throttle Position Sensor. 14 Barometric Absolute Press. Sensor. 15
and/or
23 Heated Oxygen Sensor (Inactivation). 16 EGR Function Sensor. 25 Pressure Regulator Control Solenoid Valve. 26 Purge Control Solenoid Valve. 28 EGR Vacuum Solenoid Valve. 29 EGR Vent Solenoid Valve. 34 Idle Air Control Valve. 41 VRIS 1 Solenoid Valve. 46 VRIS 2 Solenoid Valve.

Posted on Jul 12, 2010

  • yadayada
    yadayada Jul 12, 2010

    code 69 is the coolant temp senor open or disconnected

  • yadayada
    yadayada Jul 12, 2010

    Below is a link to the diagnostic routines for OBD1 Mazda fault codes, go to page 21 of the PDF file for the troubleshooting of code 69. this is a fairly large file so be patient when downloading, it is safe.



    http://eunos.com.au/data/30x/codes/CEL%2...

×

  • Level 2:

    An expert who has achieved level 2 by getting 100 points
    All-Star:

    An expert that got 10 achievements.
    MVP:

    An expert that got 5 achievements.
    Habit-Forming:

    Visited the website for 3 consecutive days.

  • Expert
  • 195 Answers

Sounds like you might need a new oxygen sensor and possibly a crank sensor. but that's a lot of codes if the engine runs without overheating it might be the computer or something along those lines.

Posted on Jun 21, 2015

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

6ya.com

Download 6ya

6ya.com

Need repair answers fast Use 6ya to...

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Check engine light on ford Taurus OBD1 scanner code 332 ERG
No such DTC for that vehicle

Oct 10, 2016 | 1999 Ford Taurus

2 Answers

Can I retrieve codes manually from a 95 bonneville
Only with a code reader.

............ and then I read this



Is it possible to read engine codes in 95 Bonneville with no scan tool

Apr 01, 2016 | Cars & Trucks

1 Answer

Ive hada code test that confirmed my 97 mazda626 needsa map sensor ive changedit and my check engine light still on is there a reason why?
Codes have nothing to do with changing any parts

OBD Fault codes are used in testing vehicle systems

You have to understand how the system that set the code
works & how the components work & how to test them, to
see if they have failed & separate the possibility of a mechanical
problem & not a sensor

Sep 22, 2014 | 1997 Mazda 626

1 Answer

What could cause a truck to run rough when there is no check engine light on it?
Multiple things depending on the year. Valve adjustment is one of those things including a damaged camshaft. Low compression is one of the cylinders is also a possibility. OBD1 is less advanced and does not monitor as many operating aspects of the engine as OBD2. OBD1 is vehicles prior to 1996 and OBD2 is vehicles produced 1996 and later. Bad spark plugs on a OBD1 system will not illuminate a check engine light while on a OBD2 system you will get a misfire code.

Jul 29, 2014 | Cars & Trucks

1 Answer

Check engine light
Go to the web site below and run a fault code test.

http://www.extreme-check-engine-light-codes.com/check-engine-light-codes/GM-1983-1995-OBD1-Decoder.html

Nov 05, 2012 | 1988 Chevrolet C1500

1 Answer

Dies driving f150 1994
The engine in this year is controlled by a computer (called the ECM), the system is called the OBD1 electronic engine control system or EEC IV by Ford. Whenever you have a problem like yours the system will store a fault code in the memory of the computer, what you need to do now is have the OBD1 system tested for codes, you can do this using the Check engine light blink out code. Go HERE to learn to run a fault code test on the EEC IV system.

Jan 31, 2012 | Cars & Trucks

1 Answer

O/d light blinks when driveing o/d seems to be engaged car has 198000 miles and runs very good also engine light is on
O/D light blinks, but with that the check engine light is ON.--- This will make your troubleshooting easier.When the check engine light comes on, and remains on, this indicates that there is error stored in your cars computer.---- Once the computer is scanned, you will get error codes, as per that error code it will point towards faulty part, which is causing the O/D light to blink.-------- Most probably the O/D light blinks, If a problem exists in No. 1 or No. 2 solenoids or speed sensors .
--------------- For car after 1995 it requires OBD2 tool and for car before 1995 it requires OBD1 tool.------- --------- You car will require OBD1 tool.There are very few auto parts store and repair centers who have OBD1 tool.In your case you required OBD1 tool.------ You can just contact local auto-parts store and they will guide you to the nearest store who has OBD1 tool.There you can get your car scanned.If there is error set in your cars computer, then you will receive the error code.As per error code it will point towards the faulty part causing this problem in your car.------------- -------------- The codes which you get is scanning will be mostly any of this following codes:--- DTC P0500 - Vehicle Speed Sensor Malfunction
. DTC P0750 - Shift Solenoid "A" Malfunction
. DTC P0753 - Shift Solenoid "A" Electrical Malfunction
. DTC P0755 - Shift Solenoid "B" Malfunction
. DTC P0758 - Shift Solenoid "B" Electrical Malfunction
. DTC P0770 - Shift Solenoid "E" (SL) Malfunction
. DTC P0773 - Shift Solenoid "E" (SL) Electrical Malfunction
. DTC P1520 - Stop Light Switch Signal Malfunction
. DTC P1705 - Direct Clutch Speed Sensor Circuit Malfunction
. DTC P1765 - Shift Solenoid Valve SLN Circuit Malfunction
. DTC P1780 - Park/Neutral Position Switch Malfunction --------------- Now it all depends on what code you get, as per that you can replace the following part.------- This will help.Thanks.Helpmech.

Jul 07, 2011 | 1995 Toyota Camry

2 Answers

Where is the code reader plug on a 1995 ford contour?
Underneath the steering wheel.

Mar 04, 2011 | 1995 Ford Contour

1 Answer

Corvette 85 light red check eng intermittent
run the trouble code test with the procedure at the link below. then post the trouble code back on fixya.

http://check-engine-light-codes.blogspot.com/2006/03/gm-1983-95-vehicles-obd1-codes-self.html

May 05, 2009 | 1985 Chevrolet Corvette

1 Answer

Check engine light, but no code
first what year it may be obd1 system roll key on and off 3 times if it is obd1 it will start flashing first code will be 1 flash then 2 quick flashes this is code 12 thta means computer is reading codes then just start counting flashes they will be intermitant ie 1 flash then 3 quick flashes means 13 and so on when you get to the end of codes it will flash 5 quick then 5 quick again that is the end of your codes

Apr 02, 2009 | 1996 Jeep Cherokee Sport

Not finding what you are looking for?

View Most Popular

Cars & Trucks

Related Question

Check engine light on ford Taurus OBD1 scanner code 332 ERG

  • 1999 Ford Taurus

Open Questions:

0 Answers

engine removal for mazda b2300 1995 modelpickup

Aug 16, 2017 | Mazda Cars & Trucks

0 Answers

I have a1998 Mazda 626 I lost the key fob but bought another one but I can't seem to program it to work need your help

Aug 15, 2017 | Mazda Cars & Trucks

0 Answers

mazda mpv can move with reverse but can't move forward with gear on. Why?

Aug 15, 2017 | Mazda Cars & Trucks

0 Answers

2002 mazda protege DX: I have the sending unit out. I need to know how to disassemble it so I can replace only the fuel pump. Never mind. Figured it out on my own.

Aug 14, 2017 | Mazda Cars & Trucks

Cars & Trucks Logo

Related Topics:

742 people viewed this question

Ask a Question

Usually answered in minutes!

Popular Questions

1995 Mazda 626

2000 Mazda 626

1996 Mazda 626

1995 Mazda 626

1998 Mazda 626

Check Out the Latest Top Trucks Report!
Check Out the Latest Top Trucks Report!

View all Fixya Reports

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7710 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

PDF Manual
Http://bisalarmes.com/fichas/MAZDA/626...

2001 Mazda 626

PDF Manual
Http://www.mazdamotorsports.com/pdfs/c...

1993 Mazda 626

PDF Manual
Http://www.mazdamotorsports.com/pdfs/c...

1997 Mazda 626

Loading...