Question about 1997 Chevrolet Monte Carlo

1 Answer

Failure to stay running

Ill start my car and within ten seconds it will just shut down. chech engine light came on the other day and hesitated the day before it shut down on me. obvioulsy have gas and my oil levels are ok

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 973 Answers

First you need to hook up a OBD II scanner to your car to find the Trouble Code for it, so a Mechanic or you can properly diagnose your car, so it can be repaired properly the first time around. You can go to any AutoZone and they can scan your car at no charge.

Posted on Jul 12, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Check Charging system light illuminates, all electrical shuts down and engine still runs on 2004 Ford Expedition 5.4l until battery dies. The opposite has also happened with the engine shutting down and...


Try replacing the "convinence control module" and bad board can cause all elec issues explained and also cause engine to cut out and other things but that is where I would start, hope this helps-

Nov 29, 2013 | 2004 Ford Expedition

1 Answer

Now my mechanic wants to know if i have another key to my car i dont can he get a key at the buick dealership a 1995 key


The Passlock family has two basic relearn procedures-a ten-minute procedure and a thirty-minute procedure-and which one you use depends on the system and what components have been replaced.

The ten-minute procedure involves trying to start the engine. If nothing happens or the engine starts and dies, the security light will be flashing. Wait ten minutes. The flashing light should go off or illuminate without flashing. When it does, turn the ignition off, wait twenty seconds, and then try to start the engine. If it starts and runs, everything is okay. If you get the same result as previously-nothing happens or the engine starts and dies with the security light flashing-wait ten more minutes.

You will now begin the thirty-minute relearn procedure, which is just the ten-minute procedure repeated three times. After turning the ignition off for the third time and waiting for twenty seconds, the engine should start and run. If it doesn't, there may still be something wrong with the system.

After the learn procedure is completed and the engine is running, the security light may stay on steady for a few minutes and then go off-this is normal. Depending on the system, replacement of key components will necessitate that a relearn procedure be completed. These include the ignition lock cylinder, Powertrain Control Module (PCM), Body Control Module (BCM), or Instrument Panel Cluster (IPC) ............ .Logic lock-up is an internal software issue within a control module which may be cleared by disconnecting and reconnecting the affected module (re-booting the system).

Electronic control modules can develop internal software issues which can cause erratic or no operation of the affected module. In most cases the module can be restored to proper operation by electrically disconnecting and reconnecting the affected module, just as you would reboot your home computer when it begins acting strangely.

Repeated Logic Lock-up failures of the same module would normally warrenty replacement of the affected module.

Aug 22, 2017 | 1995 Buick LeSabre

1 Answer

I just put a new steering column in my 200 saturn sl2 because my ignition lock was messed up. Now when whe try to start the car, it will start up but immediately shut off and then the security light...


Hello: Will try to give you instructions: Attempt to start car, leave key on (security light flashing) let set for 10 minutes, After 10 minutes security light out. Turn key off for ten seconds, turn key on, let set for 10 minutes, turn key off for 10 seconds. turn key back on let set 10 minutes, turn key off for ten seconds, the engine should now start and stay running.

Jan 14, 2011 | Saturn SL2 Cars & Trucks

1 Answer

How would I reset my 2001 Grand Am Gt! The security light stays on when I turn it to on....and no gas is getting to the engine! So everyone says that I need to reset it! BUT DONT KNOW HOW TO?


Turn key to run, click the engine but do not let it start then relax back to the run position. You will now see the security light on
After about ten minutes light will go off.
Turn key off and back on to run within 5 seconds

Repeat above procedure for a total of 3 ten minute relearns.

After done turn key off and Then start engine.

Dec 02, 2009 | 2001 Pontiac Grand Am SE

2 Answers

1997chevylumina3.1 check engine light on after


You can reset the light by disconnecting the negative battery cable for about 30 minutes. If there is still an issue with the car after running the car after reconnecting the battery it will come back on. You will need to have it checked with diagnostic tool.

Sep 06, 2009 | 1997 Chevrolet Lumina

3 Answers

2000 Jeep grand Cherokee will start then turn off


Replace the key Im the forman for a jeep dealership. The dealer should have told you that in the first place. there is no reason the key would unprogram itself unless the chip is intermitently shorting out. If you have another key start it if it stay running u know the key is at fault. hope this helps u out.

Jul 05, 2009 | 2000 Jeep Grand Cherokee

1 Answer

How do I program my key for my 2006 Chevy Impala?


Add Duplicate Key (PK3 or PK3+ key)
1. Insert an existing key into the ignition cylinder.
2. Turn the ignition cylinder to ON (RUN) and back to OFF.
3. Remove the existing key and, within fifteen seconds, insert the new key
and turn it to ON (RUN).
4. The security light will light up for two seconds to indicate success in programming
the key into the vehicle.
Originate New Master Key (PK3 or PK3+ key)

1. Insert new key into ignition cylinder and turn it to the ON (RUN) position.
The security light on the dash will illuminate and stay on for ten minutes.
2. When the security light goes out, you have one minute to start the next
step. Turn the ignition cylinder to OFF and then back to the ON (RUN)
position. The security light on the dash will illuminate and stay on for ten
more minutes.
3. When the security light goes out, you have one minute to start the next
step. Turn the ignition cylinder to OFF and then back on the ON (RUN)
position. The security light on the dash will illuminate and stay on for ten
more minutes.
4. After the security light has gone off the third time, the key has been programmed
into the vehicle’s computer and will operate the car. It has replaced ALL the
previous electronic key codes and is the ONLY key programmed into the
vehicle’s computer.

Add Duplicate Key (PK3 or PK3+ key)

1. Insert an existing key into the ignition cylinder.
2. Turn the ignition cylinder to ON (RUN) and back to OFF.
3. Remove the existing key and, within fifteen seconds, insert the new key
and turn it to ON (RUN).
4. The security light will light up for two seconds to indicate success in programming
the key into the vehicle.

May 20, 2009 | 2006 Chevrolet Impala

1 Answer

Sudden overheat


hi  ernie try changing the thermostate first as this can cause this  D

Jan 03, 2009 | 2001 Jaguar S-Type

Not finding what you are looking for?
1997 Chevrolet Monte Carlo Logo

Related Topics:

57 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8152 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...